Cisco Catalyst Express 520 Manuale utente
A-1
User Guide for the Catalyst Express 520 Switches
OL-12761-02
APPENDIX
A
Reference
Chapter Topics
•Technical Specifications, page A-2
•Location of the Switch Serial Number, page A-4
•Connector Specifications, page A-5
•Cabling Guidelines, page A-10
•Cable and Adapter Specifications, page A-13
Appendix A Reference
Technical Specifications
A-2
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Technical Specifications
This section lists the switch technical specifications in Table A-1.
Table A-1 Specifications for the Catalyst Express Switches
Environmental Ranges
Operating temperature 32 to 113°F (0 to 45°C)
Storage temperature –13 to 158°F (–25 to 70°C)
Relative humidity 10 to 85% (noncondensing)
Operating altitude Up to 10,000 ft (3049 m)
Storage altitude Up to 15,000 ft (4573 m)
Power Requirements
AC input voltage Catalyst Express 520-8PC-K9:
100 to 240 VAC, 2.5 to 1.3 A (autoranging), 50 to 60 Hz
Catalyst Express 520-24TT-K9:
100 to 240 VAC, 1.3 to 0.8 A (autoranging), 50 to 60 Hz
Catalyst Express 520-24LC-K9:
100 to 240 VAC, 2 to 1 A (autoranging), 50 to 60 Hz
Catalyst Express 520-24PC-K9:
100 to 240 VAC, 8 to 4 A (autoranging), 50 to 60 Hz
Catalyst Express 520G-24TC-K9:
100 to 240 VAC, 1.3 to 0.8 A (autoranging), 50 to 60 Hz
DC input voltages for RPS 6751+12 V @14 A, –48 V @7.8 A
Power consumption Catalyst Express 520-8PC-K9: 204 W or 696 BTUs per hour
Catalyst Express 520-24TT-K9: 30 W or 102 BTUs per hour
Catalyst Express 520-24LC-K9: 110 W or 375 BTUs per hour
Catalyst Express 520-24PC-K9: 460 W or 1570 BTUs per hour
Catalyst Express 520G-24TC-K9: 45 W or 154 BTUs per hour
Power dissipation Catalyst Express 520-8PC-K9: 80 W or 272 BTUs per hour
Catalyst Express 520-24TT-K9: 30 W or 102 BTUs per hour
Catalyst Express 520-24LC-K9: 45 W or 153 BTUs per hour
Catalyst Express 520-24PC-K9: 90 W or 307 BTUs per hour
Catalyst Express 520G-24TC-K9: 45 W or 153 BTUs per hour
A-3
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Appendix A Reference
Technical Specifications
Power rating Catalyst Express 520-8PC-K9: 0.2 KVA
Catalyst Express 520-24TT-K9: 0.050 KVA
Catalyst Express 520-24LC-K9: 0.120 KVA
Catalyst Express 520-24PC-K9: 0.460 KVA
Catalyst Express 520G-24TC-K9: 0.075 KVA
Power over Ethernet 15.4 W per port maximum
Catalyst Express 520-8PC-K9: Up to 124-W switch maximum
Catalyst Express 520-24LC-K9: Up to 62-W switch maximum
Catalyst Express 520-24PC-K9: Up to 370-W switch maximum
Physical Dimensions
Weight Catalyst Express 520-8PC-K9: 5 lb (2.3 kg)
Catalyst Express 520-24TT-K9, Catalyst Express 520-24LC-K9,
and Catalyst Express 520G-24TC-K9: 8 lb (3.7 kg)
Catalyst Express 520-24PC-K9: 12 lb (5.5 kg)
Dimensions (H x D x W) Catalyst Express 520-8PC-K9:
1.73 x 9.1 x 10.6 in. (4.4 x 23 x 26.9 cm)
Catalyst Express 520-24TT-K9, Catalyst Express 520-24LC-K9,
and Catalyst Express 520G-24TC-K9:
1.73 x 17.5 x 9.9 in. (4.39 x 44.45 x 25.15 cm)
Catalyst Express 520-24PC-K9:
1.73 x 17.5 x 14.4 in. (4.39 x 44.45 x 36.58 cm)
Acoustic Dimensions2
ISO 7770, bystander position: Operating to an ambient temperature of 86ºF (30ºC)
Catalyst Express 520-24TT-K9, Catalyst Express 520-24LC-K9, and
Catalyst Express 520G-24TC-K9: 40 dBa
Catalyst Express 520-24PC-K9: 48 dBa
1. Not all Catalyst Express 520 models have an RPS connector.
2. Not applicable to the Catalyst Express 520-8PC-K9 switch.
Table A-1 Specifications for the Catalyst Express Switches (continued)
Appendix A Reference
Location of the Switch Serial Number
A-4
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Location of the Switch Serial Number
If you contact Cisco Technical Assistance, you need to know the serial number of
your switch. See Figure A-1 to locate the serial number on your switch. You can
also find the switch serial number from the device manager Dashboard
(Figure A-2).
Figure A-1 Serial Number Location on the Catalyst Express 520-8PC-K9
Switch
Figure A-2 Serial Number Location on the Catalyst Express 520 Switches
Except the Catalyst Express 520-8PC-K9 Switch
SN: XXXNNNNXXXX
201710
SYST
ALR
PoE
ADMIN
Catalyst Express 520
Series
POWER
OVER
ETHERNET
12345678
1
202294
SN: XXXNNNNXXXX
A-5
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Appendix A Reference
Connector Specifications
Connector Specifications
This section describes the connectors on the switch.
•10/100 and 10/100/1000 Ports, page A-5
•SFP Module Ports, page A-8
•Dual-Purpose Ports, page A-9
10/100 and 10/100/1000 Ports
The 10/100 and 10/100/1000 Ethernet ports use standard RJ-45 connectors and
Ethernet pinouts with internal crossovers. These ports have the send (TD) and
receive (RD) signals internally crossed so that a twisted-pair straight-through
cable and adapter can be attached to the port. Figure A-3 shows the pinout for a
10/100 port.
Figure A-3 10/100 Port Pinouts
H5318
231 45678Pin Label
1
2
3
4
5
6
7
8
RD+
RD-
TD+
NC
NC
TD-
NC
NC
Appendix A Reference
Connector Specifications
A-6
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Figure A-4 shows the pinout for a 10/100/1000 port.
Figure A-4 10/100/1000 Port Pinouts
Caution PoE faults are caused when noncompliant cabling or powered devices are
connected to a PoE port. Only standard-compliant cabling can be used to connect
Cisco pre-standard IP Phones or wireless access points or
IEEE 802.3af-compliant devices to PoE ports. A cable or device that causes a PoE
fault must be removed from the network.
When connecting 10/100 and 10/100/1000 ports to compatible devices such as
servers, workstations, and routers, you can use a two or four twisted-pair
straight-through cable wired for 10BASE-T and 100BASE-TX. Figure A-8 shows
the two twisted-pair straight-through cable schematics. Figure A-10 shows the
four twisted-pair straight-through cable schematics.
When connecting the ports to other devices, such as switches or repeaters, you can
use a two or four twisted-pair crossover cable. Figure A-9 shows the two
twisted-pair crossover cable schematics. Figure A-11 shows the four twisted-pair
crossover cable schematics.
60915
231 45678Pin Label
1
2
3
4
5
6
7
8
TP0+
TP0-
TP1+
TP2+
TP2-
TP1-
TP3+
TP3-
A-7
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Appendix A Reference
Connector Specifications
You can the Cisco Configuration Assistant to enable the automatic
medium-dependent interface crossover (auto-MDIX) feature. When the
auto-MDIX feature is enabled, the switch detects the required cable type for
copper Ethernet connections and configures the interfaces accordingly. Therefore,
you can use either a crossover or a straight-through cable for connections to a
copper 10/100, 10/100/1000, or 1000BASE-T SFP module port on the switch,
regardless of the type of device on the other end of the connection.
The auto-MDIX feature is enabled by default.
You can use Category 3, 4, or 5 cabling when connecting to
10BASE-T-compatible devices. You must use Category 5 cabling when
connecting to 100BASE-TX-compatible devices.
Note Use a straight-through cable to connect two ports only when one port is
designated with an X. Use a crossover cable to connect two ports when both ports
are designated with an X or when both ports do not have an X.
This applies only to switches on which auto-MDIX is disabled.
Appendix A Reference
Connector Specifications
A-8
User Guide for the Catalyst Express 520 Switches
OL-12761-02
SFP Module Ports
The SFP module ports on the switch use fiber-optic SFP modules with LC
connectors (Figure A-5) and copper SFP modules with RJ-45 connectors
(Figure A-6). See the “Supported Hardware” section on page 1-14 for a list of
supported SFP modules.
Figure A-5 Fiber-Optic SFP Module LC Connector
Warning
Invisible laser radiation may be emitted from disconnected fibers or
connectors. Do not stare into beams or view directly with optical instruments.
Statement 1051
Figure A-6 Copper SFP Module RJ-45 Connector
58476
60915
231 45678Pin Label
1
2
3
4
5
6
7
8
TP0+
TP0-
TP1+
TP2+
TP2-
TP1-
TP3+
TP3-
A-9
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Appendix A Reference
Connector Specifications
Dual-Purpose Ports
The Ethernet port on a dual-purpose port uses standard RJ-45 connectors.
Figure A-7 shows the pinouts.
The SFP module slot on a dual-purpose port uses SFP modules for fiber-optic and
copper uplink ports. See the “Supported Hardware” section on page 1-14 for a list
of supported SFP modules.
Note The auto-MDIX feature is enabled by default. For configuration information for
this feature, see the Cisco Configuration Assistant online help.
Figure A-7 10/100/1000 Port Pinouts
60915
231 45678Pin Label
1
2
3
4
5
6
7
8
TP0+
TP0-
TP1+
TP2+
TP2-
TP1-
TP3+
TP3-
Appendix A Reference
Cabling Guidelines
A-10
User Guide for the Catalyst Express 520 Switches
OL-12761-02
Cabling Guidelines
This section describes the cabling guidelines for the port connections.
•Ethernet Port Connections, page A-10
•Small Form-Factor Pluggable Module Port Connections, page A-10
Ethernet Port Connections
For copper Ethernet ports, cable lengths from the switch to connected devices
must be within 328 feet (100 meters).
Use either straight-through or crossover Category 5 cables with RJ-45 connectors
to connect from the switch Ethernet ports to other devices.
Use Category 5 cables for 100BASE-TX and 1000BASE-T traffic. Use
Category 3 or Category 4 cables for 10BASE-T traffic.
Small Form-Factor Pluggable Module Port Connections
Each port must match the wave-length specifications on the other end of the cable,
and for reliable communications, the cable must not exceed the stipulated cable
length.
The dual-purpose port can be configured as either a 10/100/1000 port or as an
small form-factor pluggable (SFP) module port.
Table A-2 lists the cable specifications for the fiber-optic SFP module
connections. Each port must match the wave-length specifications on the other
end of the cable, and for reliable communications, the cable must not exceed the
stipulated cable length.
Altri manuali per Catalyst Express 520
4
Questo manuale è adatto per i seguenti modelli
10
Indice
Altri manuali Cisco Interruttore
Cisco
Cisco Nexus 9364C Manuale
Cisco
Cisco ASR 5000 Series Manuale
Cisco
Cisco 1538 series Manuale utente
Cisco
Cisco SD216 Manuale di riferimento
Cisco
Cisco Nexus 9508 NX-OS Manuale
Cisco
Cisco Small Business 200 Series Manuale di istruzioni
Cisco
Cisco TelePresence Server 7010 Guida
Cisco
Cisco 3750E-24TD - Catalyst Switch - Stackable Manuale
Cisco
Cisco Catalyst 9500 Series Manuale
Cisco
Cisco Nexus 4001I Manuale utente
Cisco
Cisco 3020 - Cisco Catalyst Blade Switch Manuale utente
Cisco
Cisco Catalyst 3120G Istruzioni utente
Cisco
Cisco SFS 7012 InfiniBand Manuale di installazione
Cisco
Cisco Nexus 9396TX Manuale utente
Cisco
Cisco NCS 4200 Series Manuale utente
Cisco
Cisco Nexus 2000 Series Manuale
Cisco
Cisco 2960 8TC - Catalyst Switch Manuale utente
Cisco
Cisco 3020 - Cisco Catalyst Blade Switch Manuale di istruzioni
Cisco
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuale
Cisco
Cisco MDS 9000 Series Manuale di istruzioni
