Cisco IGX 8 Manuale utente

APPENDIX

-1

System Specifications

This appendix contains system speciﬁcations.

General This section provides general system information on the IGX 8.

System Capacity: 1 shelf with 8 card slots.

Requires 2 dedicated front slot(s) for NPMs.

Requires 2 dedicated back slots for SCMs (1 slot with blank plate).

Up to 6 T1/E1 circuit ports.

Up to 6 T1/E1 packet trunks.

Up to 48 synchronous data ports.

Up to 25 Voice, Data, and/or Frame Relay Module groups.

Enclosure Size: IGX 8 Standalone/Rackmount:

Height: 25 ins. (63.5 cm) standalone; 24.5 ins. (62.3 cm), rack

Width: 19.9 ins. (50.5 cm), standalone; 19 ins. (48.3 cm.), rack

Depth: 26.5 ins. (67.3 cm), standalone and rack-mount

Shipping Weight: 270 pounds (122.7 kilograms)

Clearance Requirement: Min. clearance: 30 inches front; nominal 30 ins. rear; 12 ins. side.

Power Input Voltage: AC system: 100 to 240 VAC (90–264 under-voltage and

over-voltage tolerance), 47 to 63 Hz.

DC system: –42 to –56 VDC.

Each AC supply can provide up to 400 watts to the card shelves.

Space for 4 power supplies.

Current Requirements: Conﬁguration dependent - use Network Design Tool for exact

requirements. For planning purposes, use the following:

• AC System 10 Amps Max. for 110 VAC, 5 A for 220 VAC.

• DC System 20 Amps max. at –48 VDC; 25 Amps at –42 VDC (worst case)

-2 IGX 8 Installation Manual, Release 8.2.0

Voice Circuit Support

Input AC Power

Connector: IEC 16 Amp input connector. 6 different power cords are available

to comply with the standards of individual countries. Power cords

are 6 feet (about 2 meters) long. See AC Power Cabling for details.

DC Input Connections 3-wire pluggable terminal block with screw terminal connectors.

Operating Environment: 0°to 50°C (32°to 104°F). Maximum 85% relative humidity

Shock: Withstands 10 G, 10 ms. at 1/2 sine wave.

Vibration: Withstands 1/4 G, 20–500 Hz.

Heat Transfer to Room: IGX 8: 2720 BTUs max.

Voice Channel Interface: 24-channel T1 (D4 format).

24-channel T1-ESF (using CVM8).

30-channel framed CEPT E1.

31-channel framed CEPT E1.

Voice Compression

Available: 32/24/16 Kbps ADPCM.

32 Kbps ADPCM.

Voice Activity Detection compression.

Compression Algorithm: ITU-T G.721, G.723, G.726.

StrataCom 32 Kbps ADPCM.

PCM Encoding Types: Accommodates µ-Law or A-Law encoding,

End-to-end conversion available.

Channel Gain Control: –8 dB to +6 dB.

Signalling Modes: T1: Robbed bit or CCS (ISDN).

E1: Channel Associative Signalling (CAS) or Common Channel

Signalling (CCS).

Signalling Conditioning: Various make-busy and forced idle routines during circuit alarm can

be speciﬁed on a per-channel basis.

Quantizing Distortion

Added: 2.5 Quantizing Distortion Units (QDU)s with 32 Kbps ADPCM

over 1 hop plus 0.7 QDUs with Digital Loss PAD (µ-law or A-Law).

-3

Data Channel Support

Sync. Data Interfaces: RS-232C/D, RS-449/422, V.24, X.21, and V.35

with IGX 8 as DCE or DTE.

High-Speed Data Rates

(HDM): 2.4 Kbps to 1.344 Mbps.

Low-Speed Data Rates: 2.4 to 19.2 Kbps per LDM port.

Ports per card: LDI: 4 or 8.

SDI: 4.

Control Leads Supported: SDI: Per interface standards.

SDI: Up to 7 in each direction for fast EIA.

LDI: 3 in each direction for DCE and DTE for each port.

Control Lead Sync

w/Data: Control leads are sampled every 50 ms. and changes will normally

follow data within 100 to 1000 msec. Fast EIA lead will be within 1

byte.

DS0A Interface: Superrate, 56 Kbps to 512 Kbps (8 DS0s) per port.

Subrate: One 2.4/4.8/9.6/19.2/ or 56 Kbps per DS0

Per Bell TR-TSY-000458, TR-TSY-000280, TR-TSY-000083, and

TR-TSY-000077.

Data Clocking: Synchronous and isochronous clocking.

Normal, looped, and split clock conﬁgurations.

Pleisochronous

Clock Range: ±2 percent of nominal data rate.

-4 IGX 8 Installation Manual, Release 8.2.0

Digital Data Service Interface

Ports per card: Four.

Electrical Interface: Digital Data System (DDS)—AT&T Pub. 62310, November 1987.

Interface Type: DSU or OCU (software selectable).

Data Rates: 2.4, 4.8, 9.6, 19.2, and 56 Kbps (software selectable).

DDS Data Encoding: Standard DDS Bipolar Return to Zero. Alternate Mark Inversion

coding with bipolar violation sequences for zero suppression and

control.

Data Compression: Repetitive Pattern Suppression (RPS): 7, 8, or 16 bit pattern

matching.

Synchronization Modes: External (DSU only)

Looped (OCU only).

Control Codes Recognized: Idle.

Zero Suppression.

Out-of Service.

Loopback Sequences.

Control Code Translation: Translation of RTS to IDLE.

Alarm Code Translation: Translation of the logical NOR of Out-of-Service

Sync Fail.

Excessive Bipolar Violations.

No Signal to DSR (DSU only).

No Signal to DTR (OCU only).

Connector: ISO 4903, female DB-15 type connector.

-5

T1 Interface

Line Rate: 1.544 Mbps, ±50 bps (±200 bps VCO lock range).

Line Code: Bipolar AMI or B8ZS.

Framing Formats: Fractional T1, adjacent or alternating channels.

Minimum of four DS0 channels required.

Signal Level: DSX-1 compatible.

Line Impedance: Terminated = 100 Ohms nominal. Bridged = 1 KOhm.

Pulse Amplitude Individual pulse amplitude 2.4 V–3.6 V (making a total

base-to-peak amplitude of 6 V ±.6V)

Minimum Pulse Density: Zero code suppression, either LSB or MSB.

Frame Format: D4 and Extended Superframe (ESF).

VF Signalling: Robbed bit D4 with A and B bits.

Max. Line Lengths: Up to 533 feet with equalizers using ABAM cable.

Jitter Transfer: Meets AT&T PUB 62411 speciﬁcations.

Jitter Tolerance: Meets ANSI standards and AT&T PUB 62411 specs.

Connector: DB 15 female.

-6 IGX 8 Installation Manual, Release 8.2.0

E1 Interface

Line Rate: 2.048 Mbps, ±50 bps (±200 bps VCO lock range)

Line Code: Bipolar AMI or HDB3

Line Impedance: 120 Ohms (balanced) or 75 Ohms (balanced or unbalanced)

Minimum Pulse Density: Zero code suppression via HDB3 coding

Frame Format: Unframed, 32-channel (G.703). Framed: 30 or 31-channel CEPT

multiframe per ITU-T G.704.

VF Signalling: CAS or CCS

Max. Line Lengths: E1 output complies with G.703, so cabling must not exceed

–6dB/1000 feet at 1024 kHz (applies to 75 Ohm coax or 120 Ohm

twisted pair up to 350 meters or 1000 feet). StrataCom supplies

cable with a maximum attenuation of 7 dB /1000 ft., so the

maximum length of this cable is 850 feet (260 meters).

Jitter: Meets G.823.

Electrical Interface: Complies with G.703 Speciﬁcation.

Connector: DB 15 female or BNC.

-7

T3 Interface

Line Rate: 44.736 Mbps ±20 ppm, asynchronous.

Line Code: B3ZS.

Clock Source Mode: Internal (Asynchronous).

Signal Level: DSX-3.

Framing Formats: M13 mode, C-bit parity.

Alarms Processed: AIS.

LOS.

Remote Alarm Indication.

Loss Of Framing.

Line Errors Counted: BPV.

Parity Bit Errors.

Receiver Input Impedance: Terminated = 75 ohms.

Transmission Modes: Point-to-Point or Drop and Insert.

Jitter: Meets ACCUNET T45 speciﬁcation (Pub 54014).

Connector: 75 ohm BNC.

Max. Line Lengths: 450 ft. (137 m.) to DSX-3 using 75 Ohm coaxial cable.

Indicators: RED Alarm.

YELLOW Alarm.

LOS.

AIS.

-8 IGX 8 Installation Manual, Release 8.2.0

E3 Interface

Line Rate: 34.368 Mbps ±20 ppm, asynchronous.

Line Code: HDB3.

Clock Source Mode: Internal (Asynchronous).

Signal Level: ITU-T G.703

Framing Formats: ITU-T G.804, G.832,

Alarms Processed: AIS.

LOS.

Remote Alarm Indication.

Loss Of Framing.

Line Errors Counted: BPV.

Parity Bit Errors.

Receiver Input Impedance: 75 ohms unbalanced.

Transmission Modes: Point-to-Point or Drop and Insert.

Jitter: per ITU-T G.823.

Connector: 75 ohm BNC.

Max. Line Lengths: 137 meters (450 ft.) using speciﬁed cable.

Indicators: RED Alarm.

YELLOW Alarm.

LOS.

AIS.

-9

Frame Relay Interface

Type of Service: Permanent Virtual Circuit (PVC).

Data Interface: Per ITU-T I.122 and ANSI T1/S1 Standards.

Data Transfer Protocol: LAP-D frame level core functions.

Input Data Format: High Level Data Link (HDLC) protocol.

Input Data Frame Length: Up to 4096 bytes max.

Frame Integrity Check: Frame Check Sequence and CRC check of data frame. If CRC fails,

data frame is discarded at receiving node.

Input Data Rate: 56 Kbps to 2.048 Mbps. (Max. rate available only with one of four

ports/card active).

No. of Ports per Card: 4

No. of PVCs per Port: 252 per FR card, distributed in any combination.

Port Electrical Interface: ITU-T V.35. IGX 8 can act as a DCE or DTE for direction of control

leads and timing.

Data Clocking: Normal or looped.

Virtual Circuit Identiﬁer: Data Link Connection Identiﬁer (DLCI).

Control Protocol: Local Management Interface with XON/XOFF type ﬂow control.

IGX sets FECN and BECN bits in frame relay frame.

Bundled Connections: 252 virtual circuits per card

1024 virtual circuits per node.

Billing Time Accuracy: Upon request from user device, IGX will provide GMT from any

node accurate to within 1 second.

-10 IGX 8 Installation Manual, Release 8.2.0

ATM Interface

Network Synchronization

Type of Service: Permanent Virtual Circuit (PVC)

Interface Types: User-to-Network (UNI) and Network-to-Network (NNI) per ITU

I.361 and I.363

Data Rates: T3 or E3

ATM Layer: Physical Layer Convergence Protocol per AT&T publication

TA-TSY-00772 and 000773 for T3; ITU I-361 with HEC for E3

Cell Rate: 96,000 cells/sec. for T3, 80,000 cells/sec. for E3

Adaptation Layer: AAL5

No. of Ports per card: 4

No. of PVCs per card: 255

VPI Addressing Range: 0–255

VCI Addressing Range: 0–65535

Trafﬁc Queues: CBR, VBR, and ABR

Management Protocol: Interim Layer Management Interface (ILMI)

External Clock Sources: The IGX switch synchronizes to the nearest, highest-stratm clock available.

Any T1, E1, T3, E3, OC3 (STM-1) line, trunk, or optional external clock

inputs can serve a clock source.

Internal to Node Source: T1: 1.544 MHz, ±10 ppm (stratm 4)

E1: 2.048 MHz, ±10 ppm (stratm 4)

Clocking Hierarchy: Dynamic primary, secondary, and tertiary clocking

Without a deﬁned external clock reference, the IGX defaults to its internal

clock source.

Indice

Altri manuali Cisco Interruttore

Cisco

Cisco 9134 - MDS Multilayer Fabric Switch Come usare

Cisco

Cisco 11503 - CSS Content Services Switch Manuale di istruzioni

Cisco

Cisco Catalyst C9200L-48PXG-4X-E Manuale

Cisco

Cisco NCS 4200 Series Manuale utente

Cisco

Cisco SRW248G4P Manuale utente

Cisco

Cisco ME 3400G-2CS - Ethernet Access Switch Manuale utente

Cisco

Cisco Catalyst 3560-X-24T Manuale utente

Cisco

Cisco WS-C2955T-12 Guida rapida

Cisco

Cisco CSS 11506 Manuale utente

Cisco

Cisco MDS 9000 Series Manuale di installazione

Cisco

Cisco Catalyst 4500 E Series Supervisor Engine 9-E Guida rapida

Cisco

Cisco Catalyst 1900 Series Manuale utente

Cisco

Cisco Nexus 4001I Manuale utente

Cisco

Cisco Catalyst 2960 Series Manuale utente

Cisco

Cisco SGE2000 - Cisco - Gigabit Switch Manuale di istruzioni

Cisco

Cisco 4503 - Catalyst Switch Istruzioni per l'uso e l'installazione

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuale di istruzioni

Cisco

Cisco MDS 9200 Series Manuale utente

Cisco

Cisco Catalyst 3750 Metro Manuale di installazione

Cisco

Cisco Catalyst Series Switch 2940 Manuale utente

Cisco

Cisco 11154 - CSS - Switch Manuale utente

Cisco

Cisco Nexus 93180YC-FX3S Manuale utente

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuale di istruzioni

Cisco

Cisco BPX-BXM-155-8DX Manuale dell'operatore

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente