Cisco Meraki MX64 Manuale utente

MX84 Installation Guide

This document describes how to install and set up the MX84 security

appliance. Additional reference documents are available online at:

www.meraki.com/library/products.

MX84 Overview

The Meraki MX84 is an enterprise security appliance designed for

distributed deployments that require remote administration. It is ideal for

network administrators who demand both ease of deployment and a

state-of-the-art feature set. This security appliance provides the

following new features:

• USB port, to support approved 3G/4G cards for failover to cellular

networks.

• Support for eight configurable GbE (RJ45) connections.

• Two GbE SFP connections (requires optional Meraki SFP-1GB-SX

transceiver).

• Dedicated management port.

• Front-panel rack mounts.

Package contents

In addition to the MX84, the following are provided.

The MX84 front panel

Ports and Status Indicators

The MX84 uses LEDs to inform the user of the device's status. When the device powers on, all the Internet LEDs flash

twice. Additional functions are described below, from left to right.

Item Function LED Status Meaning

Solid orange Power is applied

Flashing white Operation in progress

1 Power

Solid white Fully operational

Off During boot or no USB

link

Solid Orange Initial link

Flashing orange Internet connectivity not

complete

2 USB connectivity

Green USB connection detected

Off No high availability

available

Solid orange Initial link

Flashing orange High availability not

complete

HA status

Green High availability available

Additional functions on the front panel are described below, from left to right.

USB port USB 2.0 for 3G/4G wireless cards. Traffic status is

indicated by the USB LED.

The MX84 back panel

Additional functions on the front panel are described below, from left to right.

Reset button

Insert a paper clip if a reset is required.

• A brief, momentary press: To delete a downloaded configuration and reboot.

• Press and hold for more than 10 sec: To force the unit into a full factory reset.

Please note that the serial number is located on the product label at the back panel of MX84.

Mounting hardware

The mounting hardware includes four sets of standard slot-head rack screws and nuts. The additional screws and nuts

are for use with optional rear brackets if rear support is required. When installing the appliance, make sure that there is

sufficient space between the rear of the rack and other obstacles to ensure adequate airflow.

Safety guidelines

Regardless if you are using a wall power outlet (MAINS) or any other type of power connection (e.g., a UPC device),

always ensure that the power cord can be readily disconnected from the hardware unit.

Connecting to WAN

All Meraki MX devices must have an IP address. This section describes how to configure your local area network before

you deploy it. A local management web service, running on the appliance, is accessed through a browser running on a

client PC. This web service is used for configuring and monitoring basic ISP/WAN connectivity.

Setting up a static IP address

To ensure that the client PC is redirected to the local web service in the following step, you must disable all other

network services (ex: wi-fi) on your client machine.

Do the following to configure basic connectivity and other networking parameters:

1. Using a client machine such as a laptop, connect to the management port of the MX.

2. Using a browser on the client machine, access the appliance's built-in web service by browsing to

http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)

3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as

the username, with a blank password field.

4. Choose Static for the IP Assignment option.

5. Enter the IP address, subnet mask, default gateway IP and DNS server information.

Setting up a DHCP IP address

By default all MX devices are configured to DHCP from upstream WAN / ISP servers. Simply plug the MX's WAN /

Internet port to your upstream circuit and wait a few minutes for the unit to negotiate a DHCP address.

When the WAN connection is fully enabled, Internet LED will turn white.

Additional settings

Please note that all these settings below are accessible only via the local management console.

Setting VLANs

If your WAN uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for

VLAN ID for your network.

Setting up secondary WAN interface (dual WAN)

The MX84 comes with two dedicated Internet ports, which are both configured through the Uplink configuration under

the Local status tab.

Setting PPPoE

PPPoE authentication may be required if you are connecting MX device to a DSL circuit. You need to know your

authentication option and credentials (supplied by your ISP) in order to complete these steps.

• Choose Connection Type > PPPoE.

• Select your Authentication option.

• If you select Use authentication, enter appropriate values for Username and Password.

Web proxy settings

These settings take effect if the MX device has to fall back to using HTTP to contact the Cloud Controller. By default,

web proxy is disabled. To enable web proxy, do the following:

• Choose Web proxy > Yes.

• Enter values as appropriate for Hostname or IP and Port.

• If you require authentication, choose Authentication > Use authentication, and enter appropriate values for

Username and Password.

To apply all configuration settings to the appliance, be sure to click Save Settings at the bottom of the page.

Configuring physical link settings

To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable

half duplex, full duplex, and autonegotiation, as well as set 10- or 100-Mbps data rates.

Indice

Altri manuali Cisco Interruttore

Cisco

Cisco MDS 9132T Guida rapida

Cisco

Cisco ME 3400 Series Manuale utente

Cisco

Cisco Topspin 360 Manuale utente

Cisco

Cisco Catalyst 3560-CX Manuale utente

Cisco

Cisco Catalyst 9400 Series Istruzioni operative

Cisco

Cisco Catalyst 3550 Manuale utente

Cisco

Cisco Nexus 9200 Series Manuale utente

Cisco

Cisco TelePresence Server 7010 Guida

Cisco

Cisco Nexus 7000 Series Manuale utente

Cisco

Cisco Catalyst 3560-24PS Dimensioni

Cisco

Cisco MDS 9000 Series Manuale di istruzioni

Cisco

Cisco Catalyst 3560-X-24T Manuale utente

Cisco

Cisco MDS 9124V-K9 Manuale

Cisco

Cisco SRW2024P - Small Business Managed Switch Manuale utente

Cisco

Cisco Catalyst 9500 Series Manuale

Cisco

Cisco BPX 8600 Series Manuale utente

Cisco

Cisco 100 Series Manuale utente

Cisco

Cisco Catalyst 4500 Series Manuale di installazione e funzionamento

Cisco

Cisco ESW 500 Series Manuale utente

Cisco

Cisco HWIC-4ESW - EtherSwitch HWIC Switch Manuale utente

Cisco

Cisco Nexus 9508 Manuale

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuale utente

Cisco

Cisco Catalyst 4500 E Supervisor Engine 6-E Series Guida rapida

Cisco

Cisco Linksys SFE2000 Manuale di istruzioni

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente