Cisco SG300 series Manuale utente

Cisco SG300 Setup Guide

When used with ELAN Video Over IP products

Cisco SG300 SETUP GUIDE

www.elanhomesystems.com

Contents

Introduction 03

Cisco Feature Requirements 03

Connecting To The Web GUI Interface 04

Activating Layer 3 Mode 05

Jumbo Frames 06

IGMP Snooping 07-09

Turning On/O POE 10

Apply And Save Settings 11

Changing Your Computer IP Address 12-14

Cisco SG300 SETUP GUIDE

contact [email protected]

The ELAN Video Over IP solution requires a layer 3 Managed switch in order for

HDMI distribution to be achieved reliably and with no loss in performance.

The following guide is a step-by-step instruction on how to connect and congure

your Cisco SG300 Layer 3 Managed network switch.

Introduction

The following features need to be enabled on the Cisco network switch:-

1. Layer 3 mode

2. Jumbo Frame

3. IGMP Snooping/Video Over IP

4. POE (if utilised)

Feature explanation:

• Video Over IP (one-to-many or many-to-many distribution) is group communication where information is addressed to a

group of network devices simultaneously (ELAN Video Over IP products).

• Jumbo frames are Ethernet frames with more than 1500 bytes of payload. Conventionally, jumbo frames can carry up

to 9000 bytes of payload and must be activated in order to send large packets of data for HDMI distribution.

• IGMP management & snooping is the process of listening to Internet Group Management Protocol (IGMP) network trac.

The feature allows a network switch to listen in on the IGMP conversation between hosts, routers & receivers (Video

Over IP Transmitter, network switch and Video Over IP Receiver). By listening to this ow of trac the switch maintains

a map of which links need which IP Video Over IP streams. (which ELAN Video Over IP products are active and where

the signal is being distributed to).

Cisco feature requirements

Cisco SG300 SETUP GUIDE

www.elanhomesystems.com

Connecting to the switch Web GUI Interface

V2 Panel Description

To login into the Cisco network switch the factory default details are:

IP Address: 192.168.1.254

User: cisco

Password: cisco

In order to connect to the network switch your computer will need to be physically connected to the Cisco switch using a Ethernet

network cable.The computer must also be in the same IP range as the Cisco switch default IP address. If you are unsure how to update your

computer IP range follow the‘Changing your computer IP address’instructions at the rear of this guide.

1) Open your internet browser (Google Chrome, Mozilla, Internet Explorer etc)

2) Type the network switch default IP address into the web browser bar

3) Enter the default user name and password

Note: If the switch is not using the factory default settings you will need to know these login details or have to factory reset the unit.

For details how to factory reset the network switch please refer to the networks switch user manual.

Cisco SG300 SETUP GUIDE

contact [email protected]

The rst setting you MUST update is to turn the network switch to Layer 3 mode. This must be completed before all other setting

changes are made as this will default the factory settings when Layer 3 is activated.

Under ‘Administration’menu

Select ‘System settings’

Tick‘L3’(Layer 3) checkbox adjacent to System mode

Activating Layer 3 mode

Click‘Apply’to update the setting. A warning message will appear to make sure that you mean to factory reset the switch. Click

‘OK’to proceed.

Please note: The switch will reboot which will take 3-4 minutes. After this is complete you will have to re-enter new password

details

Cisco SG300 SETUP GUIDE

www.elanhomesystems.com

To enable Jumbo Frame,

Under ‘Port Management’menu

Select ‘Port settings’

Tick‘ENABLED’checkbox adjacent to Jmubo Frames

tick‘Jumbo Frame’checkbox under Port Settings

Jumbo Frame

Click‘Apply’to update the setting

Cisco SG300 SETUP GUIDE

contact [email protected]

To enable IGMP snooping, there are several steps required to enable this feature:-

• Bridge Video Over IP Filter Status

• IGMP Snooping Status

• IGMP Querier Status

• MRouter Ports Auto Learn

• Immediate Leave

• IGMP Querier Election

The following pages explain how to update the above settings.

IGMP Snooping

Under‘Video Over IP’menu

Select ‘Properties’

Tick‘Enabled’checkbox adjacent to‘Bridge Video Over IP Filter Status’

IGMP Snooping - Bridge Video Over IP Filter Status

Conrm other settings match those as shown in the above image

Click‘APPLY’to update the setting

Cisco SG300 SETUP GUIDE

www.elanhomesystems.com

Under‘Video Over IP’menu

Select ‘IPv4 Video Over IP Conguration’

Select ‘IGMP Snooping’

Tick‘Enabled’checkbox adjacent to IGMP Snooping Status

Tick‘Enabled’checkbox adjacent to IGMP Query Status

IGMP Snooping - IGMP Snooping Status

Conrm other settings match those as shown in the above image

Click‘APPLY’to update the setting

Cisco SG300 SETUP GUIDE

contact [email protected]

Under‘Video Over IP’menu

Select ‘IPv4 Video Over IP Conguration’

Select ‘IGMP Snooping’

Select Line 1 in the IGMP Snooping table and click the ‘EDIT’button

IGMP Snooping - IGMP Query Status, Mrouter ports auto

learn, Immediate leave & IGMP querier election

Tick‘Enabled’checkbox adjacent to IGMP Snooping Status

Tick‘Enabled’checkbox adjacent to Mrouter ports auto learn

Tick‘Enabled’checkbox adjacent to immediate leave

Tick‘Enabled’checkbox adjacent to IGMP querier status

Tick‘Enabled’checkbox adjacent to IGMP querier election

Conrm other settings match those as shown in the above image

Click‘APPLY’to update the setting

the following pop-up window will appear

Cisco SG300 SETUP GUIDE

www.elanhomesystems.com

Not all Cisco SG300 switches support POE. Those network switches that do support POE come with this as factory default to

‘ON’. If you are unsure of the port setting please follow the below instructions.

Under‘Port management’ menu

Select ‘POE’

Select ‘settings’

The following table shows the settings for each RJ45 LAN port on the network switch. POE administrative Status should be set to

‘Enabled’meaning the POE feature is active. Default settings are for POE to be active (Enabled) so changes shoudl not be required.

If status is‘Disabled please follow below instructions.

Turning On/O POE

To update the port settings click‘EDIT’which will open the following window:

Tick‘Enabled’checkbox for each interface (switch LAN connection) you wish POE to be active.

Click‘APPLY’to update the setting

Altri manuali per SG300 series

Indice

Altri manuali Cisco Interruttore

Cisco

Cisco Cisco Small Business Unmanaged Switch SR2016 Manuale utente

Cisco

Cisco Nexus 5596UP Manuale

Cisco

Cisco Catalyst 4500 Series Guida all'installazione

Cisco

Cisco Catalyst 2960 Series Manuale utente

Cisco

Cisco Catalyst Express 520 Manuale utente

Cisco

Cisco SRW2008MP Manuale utente

Cisco

Cisco 300 Series Manuale di istruzioni

Cisco

Cisco Business 250 Series Istruzioni operative e di manutenzione

Cisco

Cisco 4948 Series Manuale utente

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuale di istruzioni

Cisco

Cisco Catalyst 3750-E Series Dimensioni

Cisco

Cisco Nexus 5548P Manuale utente

Cisco

Cisco 200E Series Manuale utente

Cisco

Cisco Nexus 9364C-GX Manuale

Cisco

Cisco 100 Series Manuale utente

Cisco

Cisco Nexus 7000 Series Manuale utente

Cisco

Cisco SGE2000 Manuale utente

Cisco

Cisco SD208P Manuale utente

Cisco

Cisco SRW2008 - Small Business Managed Switch Manuale utente

Cisco

Cisco Nexus 7004 Manuale di installazione e funzionamento

Cisco

Cisco Catalyst 9400 Series Manuale utente

Cisco

Cisco 2975 - Catalyst LAN Base Switch Manuale

Cisco

Cisco Catalyst 3550 Manuale

Cisco

Cisco Nexus 7000 Series Manuale di installazione e funzionamento

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente