Cisco Meraki MR12 Manuale utente

Assigning Static IP Addresses to an MR12 or MR58

The MR12 and MR58 wireless access points have two Ethernet ports that can be used to connect the device to a wired network. However, a static IP can only

be set on the primary Ethernet interface.

This article will discuss:

• Identifying the primary Ethernet port

• Behavior differences between primary and secondary ports

• Determining which port is being used

•Assigning a static IP

Identifying the Primary Ethernet Port

MR12

The primary Ethernet port is directly adjacent to the power connector and is labeled as Uplink.

MR58

The primary Ethernet port is located on the bottom-left side of the AP and is labeled as ETH0.

Behavior differences between primary and secondary ports

Primary (Ethernet 0)

This interface is capable of receiving power using PoE and can be assigned a static IP address. It is also capable of 10/100/1000Mbps speeds. It is intended for

connecting the MR12 to the rest of the network.

Secondary (Ethernet 1)

This interface can only receive an IP from DHCP and is not able to receive power using PoE. It is only capable of 10/100 speeds. It is still able to connect to the

Meraki Cloud Controller if the Primary connection is down, but is intended for used by a wired client. To allow use by a wired client, please refer to our

documentation regarding Extending the LAN with a Wireless Mesh Link.

Determining which port is being used

The simplest way to determine which port is being used is to physically look at the device, and refer to the diagrams above. If you are not near the device, the

easiest way to determine if the secondary port is being used is by looking at the AP Dashboard. Navigate to Monitor > Access points and click the AP in

question. Look under Status for LAN IP #. If the # = 1, then the AP is connected using the primary port. If # = 2, then the AP is connected using its secondary

port.

Assigning a static IP

A static IP can be assigned to the AP's primary interface in two ways.

Dashboard

1. In Dashboard, go to Monitor > Access points and select the AP in question.

2. Click the Edit icon.

3. On the page that appears, next to IP type select Static IP.

4. Enter the appropriate settings and click Save.

Local web interface

Refer to the MR Quick Start Guide for instructions on how to set the IP address using the local web interface.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Punto di accesso wireless

Cisco

Cisco WAP300N Manuale utente

Cisco

Cisco WAP200 - Small Business Wireless-G Access... Manuale utente

Cisco

Cisco Aironet 1500 Series Manuale utente

Cisco

Cisco MR18 Manuale utente

Cisco

Cisco Catalyst 9120AX Series Manuale utente

Cisco

Cisco AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access... Manuale utente

Cisco

Cisco Aironet 1260 Series Manuale utente

Cisco

Cisco Wap581 Manuale di istruzioni

Cisco

Cisco Aironet 3502P Manuale utente

Cisco

Cisco WAP131 Manuale di istruzioni

Cisco

Cisco Meraki CW91661-MR Manuale

Cisco

Cisco Meraki Go GR62 Manuale utente

Cisco

Cisco Small Business WAP551 Manuale utente

Cisco

Cisco Small Business Pro Manuale utente

Cisco

Cisco WAP125 Manuale di servizio

Cisco

Cisco Aironet 600 Series Manuale utente

Cisco

Cisco Aironet 521 Manuale utente

Cisco

Cisco WAP150 Manuale utente

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manuale utente

Cisco

Cisco Linksys WAP54GX Istruzioni operative originali

Cisco

Cisco Catalyst 9136I Series Manuale utente

Cisco

Cisco GR10-HW-EU Manuale utente

Cisco

Cisco MERAKI MR72 Manuale utente

Cisco

Cisco Aironet 350 Series Manuale

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente