Citizen CMP-10 Manuale di installazione
Command Reference
MOBILE LINE THERMAL PRINTER
MODEL CMP-10
Rev. 3.10 Revised on Dec 13, 2006
Rev. No. Date Comment
Rev. 1.00 2002/11/15 Newly issued
Rev. 1.01 2002/12/18 Revised P. 1, P. 2, P. 47, P. 54, P. 56, P. 59
Rev. 1.02 2003/01/17 Added Chapter 3 (Character Codes Table) and Chapter 4
Rev. 2.00 2003/06/30 Added ESC >, ESC l, FF (Firmware Ver. 1.95)
Revised GS )
Added Chapter 5 to Chapter 10
Rev. 3.00 2006/07/13 Added baud rate 38400 at page of ESC S n and 5.1 (2)
Added GS z
Rev. 3.01 2006/08/31 Revised range of CODE128 on Page56
Rev. 3.10 2006/12/13 Added new Chapter 4. Deleted [Remarks] on page 63.
REVISION
— 1 —
1. CMP-10 COMMAND SET
Code Command Function Page
1BEL Sounds the Buzzer 4
2HT Horizontal Tab Command 5
3LF Printing and Paper Feed Command 6
4CRPrint one line Command 7
5ESC RS Sounds the Buzzer 7
6ESC SP Setting the right space amount of the
character 8
7ESC ! Collective Specifying Printing Mode 9
8ESC $ Specifying the Absolute Positions 11
9ESC % Specifying/Canceling Download Character Set 12
10 ESC & Define user characters 13
11 ESC * Specifying the Bit Image Mode 14
12 ESC + Switch OFF the printer 17
13 ESC – Specifying/ Canceling Underline 17
14 ESC . Printer self test 18
15 ESC 2 Specifying 1/6-inch line feed rate 18
16 ESC 3 Setting line feed rate of minimum pitch 19
17 ESC = Data Input Control 20
18 ESC > Saving current setting 21
19 ESC ? Reading magnetic stripe reader 22
20 ESC @ Initializing the Printer 23
21 ESC D Setting Horizontal Tab Position 24
22 ESC E Specifying/canceling highlighting 25
23 ESC G Specifying/canceling Double Printing 26
24 ESC J Printing and feeding paper n/203 inch 27
25 ESC R Selecting Code table 27
26 ESC S Setting serial interface communication speed 28
27 ESC T Printing Diagnostic information 28
28 ESC V Specifying/Canceling 90°-right- turned
Characters 29
29 ESC Y Specifying print density 30
30 ESC Z Returning diagnostic information 31
31 ESC \ Specifying the relative positions 34
32 ESC _ Setting the printer in default state 34
33 ESC ` Returning the battery voltage and Printer
Head temperature 35
34 ESC a Aligning the characters 36
35 ESC c5 Enabling/Disabling Panel Switches 37
36 ESC d Printing and Feeding the paper by n lines 38
37 ESC v Transmitting the printer status 39
38 ESC x Selecting the time interval for automatically
switching Off the printer 40
39 ESC { Specifying/Canceling the Inverted Characters 41
40 GS ) Setting of printer flags 42
41 GS * Defining the Download Bit Image (LOGO) 43
42 GS / Printing the Download, Bit Image 44
43 GS : Starting/Ending Macro Definition 45
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
— 2 —
Code Command Function Page
44 GS H Selecting of Printing Position of HRI Code 46
45 GS L Setting the left margin 47
46 GS W Setting the print area width 48
47 GS ^ Executing the Macro 50
48 GS a Enabling/Disabling
ASB (Automatic Status Back) 51
49 GS f Selecting the font of HRI characters 54
50 GS h Selecting the height of the Bar Code 55
51 GS k Printing the bar code 56
52 GS w Selecting the horizontal size (Scale factor) of the Bar Code 61
53 GS z Saving AT command sequences to send to Bluetooth module 62
54 ESC l Specify/canceling black mark function 64
55 FF Printing and paper feeding to the black mark position 64
* indicates a unique command or a non-compatible command.
*
*
— 3 —
2. COMMAND DETAILS
2.1 Description of Items
XXXX ALL
[Function] Command Function
[Code] A sequence of code constituting a command is represented in hexadecimal number
for < >H, binary number for < >B, and decimal number for < >, respectively; [ ]k
represents a repeat count of k-times.
[Range] Indicates an argument value (setting range) for the command in hexadecimal number
(partly in decimal number).
* When used for application other than defined in each control, an error may occur.
Always use in the defined range.
[Outline] Describes a command outline.
[Caution] Describes a caution as required.
[Default] Describes an initial value in hexadecimal number for the command when accompanied
by an argument.
[See Also] Describes the associated commands for use.
[Sample Program] Describes a coding example in the Q-BASIC sample program.
* This example is only for your reference and differs depending on the language
used, version, and so on. For details, see the manual for the language used.
— 4 —
BEL
[Function] Sounds the Buzzer
[Code] <07>H
[Outline] By executing this command the buzzer will beep.
This command functions in the same manner as ESC RS.
— 5 —
HT
[Function] Horizontal Tab Command
[Code] <09>H
[Outline] Shifts the printing position to the next horizontal tab position.
•Ignored when the next horizontal tab position has not been set.
[Caution] •The horizontal tab position is set by ESC D.
•Initial setting of the horizontal tab position is each 8 characters in 9th, 17th, 25th,
columns from FONT A.
[See Also] ESC D
[Sample Program]
PRINT #1, “0123456789012345678901”;
PRINT #1, CHR$ (&HA);
PRINT #1, CHR$ (&H9) + “AAA”;
PRINT #1, CHR$ (&H9) + “BBB”;
PRINT #1, CHR$ (&HA);
PRINT #1, CHR$ (&H1B) + “D”;
PRINT #1, CHR$ (3) + CHR$ (7) + CHR$ (14) + CHR$ (0);
PRINT #1, CHR$ (&H9) + “AAA”;
PRINT #1, CHR$ (&H9) + “BBB”;
PRINT #1, CHR$ (&H9) + “CCC” + CHR$ (&HA);
[Print Results]
123456789012345678901
AAA BBB
AAA BBB CCC
← Initially set horizontal tab
← When set to the 4th, 8th, and 15th digits
— 6 —
LF
[Function] Printing and Paper Feed Command
[Code] <0A>H
[Outline] Prints data inside the input buffer and feeds lines based on the line feed amount
having been set.
•The head of the line becomes the next print starting position.
[See Also] ESC 2, ESC 3
[Sample Program]
PRINT #1, “AAA” + CHR$ (&HA);
PRINT #1, “BBB” + CHR$ (&HA);
PRINT #1, CHR$ (&HA);
PRINT #1, “CCC” + CHR$ (&HA);
[Print Results]
AAA ← Print and line feed
BBB ← Print and line feed
← Line feed only
CCC ← Print and line feed
— 7 —
CR
[Function] Print one line Command
[Code ] <0D>H
[Outline] This command is ignored or its action is the same as LF depending on the last
execution of GS ) 2 command (FLAG SETTING COMMAND).
If Flag 2 is 0, carriage return (CR) command is ignored.
If Flag 2 is 1, CR comamnd will act as LF command.
[Default] CR command is ignored. If you want that it acts like LF command set flag 2 to 1 by
GS ) command.
[See Also] GS )
ESC RS
[Function] Sounds the Buzzer
[Code] <1B>H<1E>H
[Outline] By executing this command the buzzer will beep.
This command functions in the same manner as BEL.
— 8 —
ESC SP n
[Function] Setting the right space amount of the character
[Code] <1B>H<20>H<n>
[Range] {0 =< n =< 20(Hex)}
[Outline] The rightward space amount is set in dot unit (1/203 inch unit).
[Caution] The rightward space amount in doublewide mode is made double of the set volume.
[Default] n = 0
[Sample Program]
PRINT #1, CHR$ (&H1B) + “ “ + CHR$ (0);
PRINT #1, “AAAAA” + CHR$ (&HA);
PRINT #1, CHR$ (&H1B) + “ “ + CHR$ (1);
PRINT #1, “AAAAA” + CHR$ (&HA);
PRINT #1, CHR$ (&H1B) + “ “ + CHR$ (12);
PRINT #1, “AAAAA” + CHR$ (&HA);
[Print Results]
AAAAA ← 0-dot space
A A A A A ← 1-dot space
A A A A A ← 12-dot space
Altri manuali per CMP-10
4
Indice
Altri manuali Citizen Stampante
Citizen
Citizen iDP-3110 Manuale utente
Citizen
Citizen CT-S601IIS Manuale utente
Citizen
Citizen PPU-231II Manuale di installazione
Citizen
Citizen CLP 8301 CLP-8301 CLP-8301 Manuale utente
Citizen
Citizen PD-04C Manuale utente
Citizen
Citizen CMP-40 SERIES Manuale di installazione e funzionamento
Citizen
Citizen PPU-231 Manuale utente
Citizen
Citizen Mini Printer Manuale utente
Citizen
Citizen LINE THERMAL PRINTER CT-S280 Manuale utente
Citizen
Citizen iDP3540 Series Manuale utente
Citizen
Citizen CT-E601 Manuale utente
Citizen
Citizen CMP-20 Manuale utente
Citizen
Citizen Z-START CLP-521Z Manuale utente
Citizen
Citizen CBM-920 Manuale utente
Citizen
Citizen PROdot 350 Manuale utente
Citizen
Citizen PD-22 Manuale utente
Citizen
Citizen CT-S851 II Manuale utente
Citizen
Citizen iDP3540 Series Manuale utente
Citizen
Citizen CLP-521 Manuale utente
Citizen
Citizen CT-S4000DC Manuale utente
