ClairiTech Innovations DVS-BS Manuale di istruzioni

March 2023 Quick Start Installation Guide Rev 2.3 En

Manufactured by:

ClairiTech Innovations Inc.

1095 Ohio Rd.

Boudreau-Ouest, NB

Canada E4P 6N4

1-888-533-1348

[email protected]

https://clairitech.com/en/support/register

For detailed instructions, download the full guide at:

Installation Guides and Manuals - Humidex

Quick Start Installation Guide

English

This Guide Covers the Following Models:

(Basement)

DVS-BS

DVS-BH

DVS-HW

HCS-BS

HCS-BS myHome

(Crawl Space)

DVS-CS

DVS-CH

DVS-CE

HCS-CS

HCS-CS myHome

(BoosterFan)

DVS-CR

HCS-BSF myHome

READ AND SAVE THESE INSTRUCTIONS

Quick Start Installation

Introduction

Congratulations on the purchase of your new system which will provide you with year-round

moisture control and improved air quality for a healthy fresh and drier indoor environment. Please

take note the following safety information:

CAUTION For general ventilating use only. Do not use to exhaust hazardous or explosive material

and vapours

WARNING!! To reduce the risk of fire, electric shock, or injury to persons, observe the following:

-Installation work and electrical wiring must be done by qualified person(s) in accordance

with all applicable codes and standards, including fire-rated construction. (APTHC Only)

-When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

-Unplug or disconnect the appliance from the power supply before servicing.

a. For permanently connected systems, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent

warning device, such as a tag to the service panel.

-Do not use this appliance with any solid-state speed control device.

-Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized

service facility for examination and/or repair.

-Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar

coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic

area and where it will not be tripped over.

Combustion Appliance Present in Dwelling

With the presence of appliances evacuating air outside the building envelope (such as range hood,

bathroom fan, dryer, etc.) there should be an adequate air supply reentering the building envelope

design. If the air pressure inside the building gets lower than the barometric pressure outside air may

be drawn in from any point of entry which may include a chimney. The smoke and gases from any

combustion appliance (oil furnace, gas/wood stove, fireplace, etc.) may be drawn into the building

rather than go out the chimney.

This can be prevented by lowering the maximum ventilation rate of the system or by introducing more

make-up air inside the building. A fresh air kit (Air Supply Ventilator) is available from your dealer, to

introduce additional air supply if needed.

The system’s installation includes allowing for replenishment air coming into the basement

and crawl space either passively via a vent upstairs, open stairwell or with a mechanical

booster fan, thereby avoiding a depressurization in the lower areas.

Quick Start Installation

Service and Warranty

Consumer Limited Warranty

ClairiTech Innovations Inc. warrants to the first consumer that this product, when shipped in its

original container, will be free from defective workmanship and materials, and agrees that it will, at its

discretion, either repair the defect or replace the defective Product or part thereof with a new or

remanufactured equivalent at no charge to the purchaser for the period(s) set forth below. The

defective part must be returned to the manufacturer ClairiTech Innovations Inc. All transportation

charges are the sole responsibility of the purchaser.

This warranty does not cover any appearance items of the product nor if the items or product have

been damaged, defaced, subjected to improper voltage, abnormal service or handling, has been altered

or modified in design or construction or was installed and has been rendered inoperable for an

extended period of time.

In order to enforce the rights under this limited warranty, the purchaser must fill out and return the

warranty card within 90 days.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties

other than those described herein, or to extend the duration of any warranties beyond the time period

described herein on behalf of ClairiTech Innovations Inc.

The warranties described herein shall be the sole and exclusive warranties granted by ClairiTech and

shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner

and for the period described herein, shall constitute complete fulfillment of all liabilities and

responsibilities of ClairiTech to the purchaser with respect to the Product, and shall constitute full

satisfaction of all claims, whether based on contract, negligence, and strict liability or otherwise. In no

event shall ClairiTech be liable, or in any way responsible, for any damages or defects in the Product

which were caused by repairs or attempted repairs performed by anyone other than an authorized

servicer, unless approved by ClairiTech in writing. Nor shall ClairiTech be liable or in any way

responsible for any incidental or consequential economic or property damage.

Warranty Period for this product:

Five (5) year on parts and electrical from date of

purchase, two (2) years on all electronic components,

and (2) years on Controller. (HCS Models)

Additional Items Excluded from

Warranty Coverage (If Any):

Appearance items of the product, Exterior vent and any

printed material.

To properly validate your warranty, you must complete and return the warranty card within 90 days.

If your device is not registered, proof of purchase will be required if it requires service after approval

from our Service Department.

You can also register your warranty online http://www.clairitech.com/support/register .

This warranty is non-transferable and applies to residential use only.

Quick Start Installation

Pre-Installation

Tools Required for Installation

-Electric reciprocal or hole saw 6¼”

-Drill with a ¼” concrete bit

-Phillips or Robinson Screw Driver

-Measuring Tape

-Hammer

-Pencil

Key Installation Facts

1) Unit must be installed at floor level –up to 3” off the floor.

2) Unit should be installed as far away as possible from the source of replenishment air.

3) Outside duct must be no less than 6” and dedicated for the Unit only.

4) A sufficient replenish air passage must be provided between the location where the unit is

installed and the remaining part of the house or apartment.

5) The area within a radius of 4 feet around the unit should be clear to allow the air to be pulled

into the vents.

6) Unit should not be installed within 8 feet of combustion appliance.

IMPORTANT –What Not to Do

1) DO NOT install the unit more than approx. 3 inches off the floor.

2) DO NOT make more than one turn with the duct and the ductwork should not be longer than 3

feet in total, unless rigid ducting is used - see “Ducting”, Page 4.

3) DO NOT crush the vinyl Pipe.

4) DO NOT install the unit next to a replenishment air supply.

5) DO NOT install the unit within 8 feet of a heat source (Radiator, heater, etc…).

6) DO NOT install in remote closed off areas or where there are obstructions to the airflow.

Ideal location installation locations

For Basement and Crawlspace Models

Air drawn in by system pulls moisture off the surface floors and walls. To maximize the

effectiveness, Install the unit in the dampest, coolest, and lowest part of the basement/crawlspace. If

possible, Install the system as far away as possible from the source of replenishment air.

For BoosterFan Model

The booster fan unit should be installed no further than 20 feet from the system exhaust for optimal

performance. The air exhausted from the booster should also be directed away from the exhaust unit

by using the non-insulated flex provided.

Quick Start Installation

Installation

Replenishment air to Basement from Upstairs

The damp air exhausted by the system must be replaced by the warmer/drier air from the upper levels.

If there is no open stairwell, the airflow is restricted from coming down, then install a passive return

grille with 100 sq. inches either in the door, in the wall, or in the floor to allow unobstructed air

downstairs. Alternatively, you can shave down the door leading to the basement by 2”-3”. For the

Crawlspace with Booster Fan, a replenishment grille is provided with the booster fan.

When the flow is limited or inaccessible between rooms downstairs (if there are walls or partitions),

then install a grille 10” x 14” (or other grill configuration, having total area of not less than 100 sq. in.)

in the bottom of the door or wall to avoid having stagnant air in those areas. Otherwise interior doors

must remain open. This insures that all the air drawn into the system comes from all areas of the

basement.

Generally, for improved performance, it is best to keep all exterior basement/crawlspace doors,

windows and vents closed. This will assure that the air is replenished with the air from upstairs and

not with the humid air from outside.

Please check to make sure there are no openings/leaks around windows, doors, vents or other places,

where outside humid air can enter the basement/crawlspace. Make sure that A/C Ducts are properly

sealed and that all A/C Leads to the basement are closed. Sump Pumps holes should be properly

covered.

Selecting the Duct Location

Now that you’ve decided where to install the unit, you must select a location for a 6¼” duct hole in

the outside wall. This hole is needed to pass a duct through the outside wall. Make sure that the hole’s

location is above ground level. Also make sure that the hole doesn’t line up with a stud, electrical

wires, or pipe.

For an interior wall installation: The distance between the system’s back and the exterior wall should

not be more than 12 feet. For this application the flex has to be replaced with rigid piping. Optional:

The bottom cap may be removed for added airflow.

The replenishment air area must have a minimum size of 100 sq.in.

Quick Start Installation

Ducting

The basement models come in two sections that allow for flexibility in positioning the duct at the

most convenient height. For both models you can duct from the back of the unit, or from the top of

the unit by removing the top cover. The duct can go through an outside wall, the floor joist or window.

The duct should be vented above ground level to the outside or below ground into a window well that

is open and not sealed off to the outdoors. The outside louver should be high enough to avoid

infiltration of snow, flooding and rodents, etc. All necessary parts and outside louvers are included.

In cases where the basement height clearance is too low, the top portion of the bottom section can

be cut down by a maximum of 40 inches with a cutter, leaving the vents at the bottom intact, for a

minimum unit height of 62 inches. For extra high ceilings, an extension piece of 24 inches is available

which can be added at the top of the unit.

When ducting the unit outside, no more than 3 feet of Vinyl Flex should be used. When circumstances

require a longer span, rigid ducting can be used from the inside of the unit to the wall. The rigid duct

will improve the airflow to compensate for the additional distance the air has to flow to reach the

outside.

When replacing a pane for a window installation, use pressurized wood or similar water/rot proof

material.

Make sure that no pipes, studs or wires are in the way.

The duct has to be dedicated and not combined with any other existing ductwork in operation. Seal

well around the outside opening.

Quick Start Installation

Preparing the System for Installation

Now that an installation location has been chosen a hole must be made for the vent. Start by measuring the required

Unit height and mark the location of the hole. Remember that the units cannot be higher than 3” off the ground.

From the inside, drill a pilot hole of approximately ¼” wide

at the center of the proposed 6¼” hole.

Outside the building, find the pilot hole.

Now using a hole-saw, with the pilot hole as a guide, drill a

6¼” hole.

Brick or Concrete Wall: There are two ways of going through brick or concrete. The first method consists of using

a hammer drill. Make holes (approximately 5/8”) with the hammer drill 1” apart through the brick in a circular shape

outlining the 6 ¼” hole. Finish cutting the outer edge of the hole using a chisel. If a hammer drill is not available, a

chisel can be used. As brick is brittle chiseling from the center of the pilot hole will chip the brick easily.

Join the two halves (Bottom section must fit inside Top

section) of the basement model casing together, overlapping

the two pieces such as the desired height is obtained.

Remove screws if necessary. NOTE: If the unit has to be

shorter than 85” cut the top of the bottom part.

Secure the two halves together using ½” metal fastening

screws.

A cover plate can be used to close the gap between both

halves if necessary. Using aluminum tape or duct tape seal

the seam in the back where the two halves join together.

Note: When installing the optional 24” extension, remove top cap and straighten the 90° elbow. Use the 6”

galvanized pipe to extend the length needed. Cut the pipe to the proper length before snapping it together. Attach

the top cap to the extension cover with the 4 screws provided. Add exterior cover to the base and fasten securely

with the provided screws.

Quick Start Installation

Fasten the unit to the wall

With the help of a tie wrap attach the flex pipe to the collar on the back of the

unit before attaching the unit to the wall. Insert the other end of the flex pipe

inside the hole in the wall.

(a few Small 9/16” Screw can be used to affix the flex to the mount)

Leaving a 1-inch gap between the top of the unit and the ceiling, drill ¼”

pilot holes through the lips of the unit and the wall.

Insert the four plastics anchors in the wall with the help of a hammer.

Secure the Unit to the wall using the four 1 ¼ inch screws provided.

Attaching the Flex and Outside Vent

Roll the flat metal plate into a cylinder and interlock both ends.

Attach the vent to the newly formed 6” pipe with the ½ inch

screws provided.

From the outside, pull the flex pipe through the 6 ¼” hole onto

the 6” pipe and attach it with a 24” cable tie.

Insert four 2-inch screws to secure the vent to the outside wall.

Make sure the vent is not twisted by inserting the screws too tight

and that the flaps are working properly.

NOTE: If high winds are often present in the location of the vent, they may cause a wind noise inside the house.

If this is the case, an anti-gust hood (AGH-990) is available from your dealer.

Quick Start Installation

Installation BoosterFan

1. To minimize noise propagation, install at least 6 ft. of 6 in. insulated flex between the universal

duct boot (connected to the floor register) and the Booster Fan.

2. To further decrease noise propagation, 6 ft. of insulated flex can be used on the exhaust side

of the unit. (Not Included)

3. Flex to pipe the Booster fan away from the exhaust system. Note the airflow arrow directions

4. If the building codes in your area require a backdraft damper to be installed, it must be placed

on the exhaust side of the booster fan to limit the impact on the total airflow through the

unit.

5. This unit is typically sold with an exhaust system. If this is the case, then the Booster Fan

system is made to replace your Replenishment vent required with other exhaust systems.

Typical Installation Diagram

Quick Start Installation

Installing and Wiring the Booster Fan

To allow the booster fan to draw air from the upper levels, a universal boot must be installed. First locate a safe place

to cut out a hole to fit the universal boot. Once a safe and adequate area had been found, proceed by cutting the hole.

With the hole cut, install the universal boot which will allow the unit to pull the air down.

Once the boot has been installed, the Booster Fan can be mounted on a floor joist a minimum of 6 ft. away from the

universal boot to reduce noise. Connect the universal boot to the booster fan with the 6 in. insulated flex provided.

If the building codes in your area require a backdraft damper to be installed, it must be placed on the exhaust side of

the Booster Fan to limit the impact on the total airflow through the unit.

Note: A T-junction duct and flex can be added to the exhaust side of the Booster Fan to direct air into all areas of

the crawl space

The Following Wiring is for HCS Booster Fan Only!!!

Now that the booster fan has been installed, it must be connected to the rest of the system. Run the white cable from

the booster to the main exhaust.

Note: These steps must be completed before plugging in the booster fan.

After the white cable has been run it must be connected to the system. Make sure the main exhaust unit is unplugged

before connecting the booster fan.

Wiring Guide:

Yellow Wire –B

Green Wire –A

Black Wire –GND

Red Wire –VCC

Note: The main exhaust unit must remain unplugged until the booster fan installation is complete.

On the booster fan’s end of the cable attach the black connector

with the wiring matching the following wiring guide.

Now that the connector has been wired, insert it into the booster

fan unit.

Now that the booster fan has been installed and connected to the main exhaust unit, it can be plugged into any 115V

outlet. Afterwards, the main exhaust unit can be plugged in.

Note: A grounded extension cord with a maximum length of 10 feet may be used if necessary.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ClairiTech Innovations Fan

ClairiTech Innovations

ClairiTech Innovations HumiFresh Hybrid 200 Istruzioni operative

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio