Clarke CTT320 Manuale utente
ASSEMBLY
INSTRUCTIONS GC12/11
HEAVY-DUTY TOOL TROLLEY
Model No: CTT320
Part No: 7630630
2
INTRODUCTION
Thank you for purchasing this CLARKE Tool Trolley.
Before attempting to assemble the trolley, be sure to read these instructions
thoroughly. In doing so you will ensure the safety of yourself and that of others
around you, and you can look forward to the trolley giving you long and
satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase. This guarantee is invalid if the product is found to have been
abused or tampered with in any way, or not used for its intended purpose.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission. This guarantee does not effect
your statutory rights.
SPECIFICATIONS
erutaeF noitacificepS
thgieWtcudorPgk5.26
yticapaCdaoLdetaRlatoTgk023
)HxWxL(snoisnemiDmm0501x884x367
tnemtrapmoCegarotSyarTpoTmm5
21x584x067
)2x(srewarDllamSmm5.16x054x592
rewarDpoTmm721x054x592
rewarDelddiMmm08x054x526
rewarDmottoBmm721x0
54x526
flehSmottoBmm543x584x067
3
UNPACKING & OPERATION
Carefully remove the trolley from the packaging and check for any damage
which may have occured in transit.
Before assembling, please check contents against the following list of loose
items on page 4, and advise your Clarke dealer immediately if any parts are
missing. The keys to the top drawer are taped inside the unit.
TOOLS REQUIRED
•Phillips Screwdriver • 13 mm wrench
SAFETY PRECAUTIONS
• Do not leave the trolley unattended without the brakes being applied.
• Do not use on rough terrain. The trolley is designed for use on smooth level
flooring.
• Do not allow children to play with or ride on the trolley.
• Do not leave the trolley on any steep inclines.
• Do not use the trolley if any of the castors are damaged; have them
replaced immediately.
• Always ensure the load is favourably distributed, i.e. with heavy items on
the lower storage levels.
DURING USE
Close the top tray before locking with the key provided. The five draws are
held closed by the latch on each one. Always close the lid and the draws
before moving the trolley.
CAUTION: ONLY OPEN ONE DRAWER AT A TIME IF HEAVY TOOLS ARE
STORED INSIDE. OPENING MULTIPLE DRAWS COULD INCREASE THE RISK
OF THE UNIT TIPPING OVER.
CAUTION: ALWAYS APPLY THE BRAKES ON EACH REAR CASTER WHEN
THE TOOL TROLLEY IS NOT BEING MOVED AROUND. TAKE EXTRA CARE
WHEN MOVING THE UNIT AROUND IF THE FLOOR SURFACE IS NOT FLAT.
WARNING: NEVER EXCEED THE MAX LOAD CAPACITY AS THIS COULD
DAMAGE THE UNIT OR CAUSE PERSONAL INJURY.
TOTAL TROLLEY LOAD = 320KG. BOTTOM TRAY LOAD = 80 KG.
4
noitpircseD ytQ noitpircseD ytQ
AylbmessAflehSreppU1JrehsaWtalF61
BemarFtrohS2KtuN02
CemarFgnoL2L61x8MtloBegiarraC83
DflehSmottoB1MtuN04
EemarFrenroC4NtekcarB4
FeldnaH1OturtSsaG2
GretsaCleviwS2PeldnaHdiL1
HekarBhtiwretsaC2Q6x4MswercS2
I02x8MtloBegairraC81RyarTlooT1
SrehsaW44
COMPONENT PARTS
B C D
A
EFGH
IJ K
LMNO
P Q R S
5
Using carriage bolts (I), flat washers (J)
and nuts (K), attach the casters (G) and
(H) in matched pairs, with the braked
casters (H) at one end of the bottom tray.
ASSEMBLY
STEP 1
G
H
K
J
D
I
STEP 2
Upper end Lower end
1.4” corner frame 1”
Using the 16mm carriage bolts (L), nuts
(M) & washers (S), attach the four
corner frames (E) as shown. Take care
that the corner frames are connected
the correct way up as illustrated above.
M D
E
L
6
STEP 3
E
E
ML
C
RE
L
M
STEP 4
A
ANL
M
Using the M8 bolts (L) nuts (M)
& washers (S), attach both
the short frames (B) to the
corner frames (E). Using
further M8 bolts, nuts &
washers, attach the tool tray
(R) to the corner frames.
With the help of an assistant, align the
upper shelf assembly (A) with the top
of the corner uprights (E) and attach
using M8 bolts (L) and install stiffening
brackets (N) on the inside. At the end
of the unit with the braked castors,
leave two lower holes free for
attaching the side handle at the next
stage and secure with M8 nuts (M) &
washers (S).
7
STEP 5
P
Q
M
F
I
STEP 6
O
K
Attach the gas struts (O) to the lid
and shelf assembly with a nut (K) &
washer (S) at each end.
Fit the side handle (F) as shown, by inserting two
bolts (I) through the lower two holes & securing with
nuts and washers. The handle is best fixed to the
end of the trolley already fitted with braked casters
for safer manouvering of the trolley. Fit the lid
handle (P) to the lid using two M4 screws (Q).
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Clarke Jack
Clarke
Clarke STRONG-ARM CTJ2LP Manuale di istruzioni
Clarke
Clarke CGK4 Manuale utente
Clarke
Clarke STRONG-ARM CTJ2GLC Manuale utente
Clarke
Clarke Strong-Arm CTJ1500QULP Manuale di istruzioni
Clarke
Clarke CTJ2500SUV Manuale di istruzioni
Clarke
Clarke STRONG-ARM CTJ3GLC Manuale utente
Clarke
Clarke Strong-Arm CTJ4000G Manuale di istruzioni
Clarke
Clarke STRONG-ARM CBJ2 Manuale di installazione e funzionamento
Clarke
Clarke strong-arm CBJ30 Guida alla risoluzione dei problemi
Clarke
Clarke STRONG-ARM CTJ5GLB Manuale di istruzioni
Clarke
Clarke STRONG-ARM CTJ2B Manuale di istruzioni
Clarke
Clarke CTJ3QLGB Manuale di istruzioni
Clarke
Clarke Strong Arm CTJ3000GB Manuale di istruzioni
Clarke
Clarke STRONG-ARM CTJ1250A Manuale utente
Clarke
Clarke CFJ48 Manuale di installazione e funzionamento
Clarke
Clarke Strong-Arm CTJ2250Q Manuale di istruzioni
Clarke
Clarke CFJ60 Manuale utente
Clarke
Clarke CTJ1800AB Manuale di istruzioni
Clarke
Clarke STRONG-ARM CML3 Guida di riferimento rapido
Clarke
Clarke STRONG-ARM CTJ10GLB Manuale di istruzioni
