Clarus Technologies PCS-35 Manuale utente

PCS-35

Agitating Cleaning

Stations

Operators Manual

Manufactured by:

Clarus Technologies, LLC

2015 Alpine Way, Suite C

Bellingham, WA 98226

(360) 715-1356

Revision Date 3/12

Table of Contents

I. INTRODUCTION ............................................................................................................................. 4

II. SPECIFICATIONS ..........................................................ERROR! BOOKMARK NOT DEFINED.

III. WARRANTY INFORMATION...................................................................................................... 4

IV. SAFETY ............................................................................................................................................ 5

A. SAFETY WARNINGS........................................................................................................................... 5

B. SAFETY EQUIPMENT.......................................................................................................................... 5

V. QUICK START GUIDE................................................................................................................... 6

A. UNCRATE UNIT................................................................................................................................. 6

B. INSTALL LIGHT BAR.......................................................................................................................... 6

C. ESTABLISH WORK AREA................................................................................................................... 6

D. FILL UNIT WITH SOLVENT ................................................................................................................. 6

VI. PARTS DESCRIPTION & OPERATION ...................................................................................... 7

A. ON-BUTTON...................................................................................................................................... 7

B. LIGHT SWITCH. ................................................................................................................................. 7

C. CLEANING BRUSH............................................................................................................................. 7

D. OPTIONAL EQUIPMENT...................................................................................................................... 7

E. FLUID NOZZLE –SHUTOFF................................................................................................................. 8

F. FILTER DIFFERENTIAL PRESSURE GAUGE.......................................................................................... 8

G. FUSIBLE LINK.................................................................................................................................... 8

J. LEVELING BOLTS............................................................................................................................... 8

VII. CARE AND MAINTENANCE........................................................................................................ 8

A. SUMP MAINTENANCE........................................................................................................................ 8

B. CANISTER LID O-RING MAINTENANCE.............................................................................................. 9

C. CHANGING FILTERS........................................................................................................................... 9

D. REPLACEMENT PARTS....................................................................................................................... 9

VIII. DISPOSAL OF WASTE OIL AND BY-PRODUCTS................................................................. 11

A. SOLVENT AND SLUDGE................................................................................................................... 11

B. FILTER DISPOSAL............................................................................................................................ 11

IX. TROUBLE-SHOOTING................................................................................................................ 11

A. LIGHT DOESN’T WORK:.................................................................................................................... 12

B. FUSIBLE LINK DOESN’T LINE-UP WITH TAB ON LID:.......................................................................... 12

C. AIR GUN HAS LOW PRESSURE OR DOESN’T WORK: .......................................................................... 12

D. SOAK TANK PUMP DOESN’T WORK: ................................................................................................ 12

E. WAND/BRUSH LEAKING OR DRIPS:.................................................................................................. 12

F. CANISTER LIDS DIFFICULT TO REMOVE AND INSTALL:..................................................................... 12

G. SIGHT GLASS DIRTY OR CLOGGED:.................................................................................................. 12

H. MAIN PUMP NOT RUNNING:............................................................................................................. 12

I. PUMP RUNNING BUT NOT PUMPING FLUID: ....................................................................................... 13

J. MAIN PUMP LEAKING: ..................................................................................................................... 13

K. SLUDGE PUMP LEAKING:................................................................................................................. 13

L. PLUMBING LEAKING:....................................................................................................................... 13

M. NO POWER MAIN PUMP,LIGHT,SOAK TANK PUMP DO NOT WORK:................................................ 13

FOREWORD

1. This manual describes the procedures required to operate the Clarus PCS-35

AGITATING SOLVENT PARTS CLEANING STATION. Every effort has been

made by Clarus Technologies, LLC to assure the accuracy and reliability of the

information contained in this document. Clarus Technologies, LLC, however, makes

no representation, warranty, or guarantee in connection with this manual and hereby

expressly disclaims any liability or responsibility for loss or damage resulting from

its use or for the violation of any federal, state, provincial or municipal regulation

with which this publication may conflict.

2. The electrical components of the Clarus Parts Washer have been designed and

assembled with UL approved equipment where required.

WARNING! The operational techniques used with this equipment are more

important than the design of the equipment for the safety of the worker.

Therefore, each technician involved in the operation of the Clarus Parts

Cleaning Station must have the proper hazardous materials training.

DANGER! This system can only be used with solvent that has a minimum

flashpoint of 140 Fahrenheit. Use of solvents with flashpoints lower than 140

Fahrenheit are likely to cause a fire, Injuries or death. If you are not sure of a

solvents flashpoint refer to the appropriate MSDS sheet.

3. Clarus is not undertaking to meet the duties of employers to warn and properly train

and equip their employees, and others exposed, concerning health and safety risks

and precautions, nor undertaking their obligations under local, state, provincial or

federal laws.

4. Information concerning safety and health risks and proper precautions with respect to

particular materials and conditions should be obtained from the employer, the

manufacturer or supplier of that material, or the Material Safety Data Sheet

(“MSDS”).

CLARUS PARTS WASHER

OPERATOR’S MANUAL

I. INTRODUCTION

Congratulations on your purchase of the Clarus PCS-35 Agitating Parts Cleaning

Station! These Parts Washers are products of Clarus engineering and manufacturing.

They are made of the finest materials under a rigid quality control system. With proper

care they will give you long and satisfactory service.

To obtain the best use of your Parts Washers, please read this manual carefully. It will

help you become familiar with the operation of the equipment and contains many helpful

hints about Parts Washer maintenance.

The instructions and specifications contained in this manual were in effect as of March

2012. Due to the policy of Clarus Technologies, LLC to continually improve its

products, however, modifications in these specifications may be made at any time.

This Operators Manual was compiled for your benefit. By reading and following the

safety, setup, operation, and trouble-shooting instructions described in the manual, you

should receive many years of trouble-free operation. Familiarize yourself with the

names of the Parts Washer components, which appear as capitalized terms throughout

this manual. Read this entire manual before attempting to start and operate the

Clarus PCS-35 Agitating Parts Cleaning Station.

II. WARRANTY INFORMATION

Clarus Technologies, LLC, will for the life of the unit, repair or replace without charge,

parts which our examination proves to be defective in material or workmanship. This

warranty is valid only if the unit has not been tampered with by unauthorized persons,

misused, abused, or improperly installed and has been used in accordance with the

instructions and/or ratings supplied. The foregoing is in lieu of any other warranty or

guarantee expressed or implied, and we are not responsible for any expense (including

installation and removal), inconvenience, or consequential damage, including injury to

any person, caused by items or our manufacture or sale. Some states do not allow

certain exclusion or limitations found in this warranty so that they may not apply to you.

In any event, Clarus Technologies, LLC total liability, under all circumstances, shall not

exceed the full replacement cost of this unit.

This Limited Lifetime Parts Warranty is limited to the following components:

Main chassis

Clarus Technologies, LLC, will for the period of 1 year from the date of purchase, repair

or replace without charge, the items listed below which our examination proves to be

defective in material or workmanship. This warranty is valid only if the unit has not been

tampered with by unauthorized persons, misused, abused, or improperly installed and

has been used in accordance with the instructions and/or ratings supplied.

This 1 year Mechanical/Electrical Component Warranty covers the following

components:

Electrical control systems

Pneumatic system

Main pump

NOTE: Consumable items such as light bulbs, O-Rings and filters are excluded

from any such warranty.

IV. SAFETY

To safely operate the Clarus Parts Washer, it is essential to know the proper safety

procedures and equipment.

A. Safety Warnings.

The definitions for the safety warnings used throughout this manual are as follows:

Warning Means that if the safety information is not followed, personnel,

equipment or the environment may be damaged or hurt.

Material Safety Data Sheets (MSDS)

The MSDS provides technical information regarding use, hazards, precautions and

emergency procedures related to specific fluids. The MSDS also contain toll-free phone

numbers that may be called to provide further safety and emergency treatment

information.

Operators of the Clarus Parts Washer must have on hand an MSDS for each type

of solvent that they will be using. The MSDS are available from the solvent supplier.

In some localities it is required by law that appropriate MSDS are on hand whenever

hazardous or flammable material is being processed.

B. Safety Equipment.

1. Safety Glasses. Operators should wear safety glasses during the operation of the

Parts Washer. The major hazard is the possibility of splashing petroleum-based

fluids into the eye. If petroleum-based fluid is splashed into the eye, severe

damage may occur. First Aid treatment should be initiated immediately. Refer

to MSDS.

2. Protective Gloves. Appropriate protective gloves should be worn whenever there

is a possibility that the fluids being used may come into contact with the hands.

Different types of gloves may be required for differently types of fluids. The

local safety supply source can recommend the appropriate protective gloves.

3. Flammable. For the safety of owners and operators NO SMOKING around or

near this equipment.

V. QUICK START GUIDE

Please read entire Quick Start Guide before beginning, this will avoid possible start up

problems.

A. Uncrate Unit

1. Remove outer wrap.

2. Unbolt legs from pallet.

3. Remove Light Bar from packaging.

4. Remove all loose packing.

B. Install Light Bar

To install the light bar, attach it to the “Light Bar Bracket” located on the

center/backside of the Parts Washer unit. Nuts and bolts have been provided. Before

tightening the bolts, open the tank lid and secure it to the light bar fusible link. Do not

bend the fusible link. Tighten all bolts. Once the light bar is secured, connect the male

plug of the light bar to the female plug labeled “light bar” out of the electrical box.

C. Establish Work Area

1. Create a properly sized area for the Parts Washer to be located in. This area

should be a level, solid working area with sufficient overhead room for the light

bar. A 110 volt 15 amp circuit should be within 6 feet of this area.

2. Place the Parts Washer in working area with a forklift or pallet jack with front of

unit facing out.

3. Use front leveling feet to reduce any rocking from an uneven floor. The leveling

feet should not be used to raise the unit off the floor. Use Bubble level to level

Front/Back and Left/Right.

D. Fill Unit with Solvent

1. Once the unit is set in place, leveled and plugged in, you can fill it with solvent.

PCS-15 Parts Cleaning Stations require 17.5 gallons of solvent. PCS-25 and

WCS-25 Parts Cleaning Stations require 27.5 gallons of solvent. (NOTE! Fill

Parts Washer until fluid level gauge located on front, left corner reads full.)

2. Make sure both the cleaning bush and fluid nozzle are inside the tank before

turning the system on. Turn system on by depressing green “ON” button.

3. When unit automatically shuts off (approximately 4 minutes) check fluid level

and fill to full line.

Congratulations –your unit is ready!

VI. PARTS DESCRIPTION & OPERATION

A. On-Button.

To turn the Parts Washer on, simply depress the green “ON” switch once. This will turn

the system on for a 4-minute cycle. When the cycle is over the system will shut off

automatically. If continued operation is needed, simply depress the green “ON” button

again.

B. Light Switch.

The light switch on the control panel operates the overhead 150-watt halogen light. The

light does not automatically switch off, so the operator must manually turn the light off.

C. Cleaning Brush.

This ergonomically designed Parts Cleaning brush self cleans during use.

D. Optional Equipment.

The PCS-25/WCS-25/PCS-15 Cleaning Stations come with various options. The

following describe the operation of these options, however, not all units are equipped

with the same option packages.

Air Tool with Air Pump:

If the optional Air Tool with Air Pump was purchased for your Parts Washer, you

will have an air nozzle/handle hanging on the inside of the Parts Washer lid and

an on/off switch labeled “Air Tool”. To activate the air tool first turn the switch

to “ON”, this will start the compressor. Next, take hold of the Air Tool, point it

down and away from your body and depress the trigger on the handle. This will

release the pressurized air for use with the Parts Washer.

Regulated Shop Air Operated Air Tool:

If the optional regulated “Shop Air” model was purchased, hook up the Shop Air

Hose to the air regulator located on the backside of the lower shelf. Manually

adjust the amount of air needed by pulling up the knob on the regulator and

turning it to the appropriate setting. When the proper amount of air is achieved,

push knob down to lock your setting. With this set-up, air will always be

available at the nozzle.

Agitation Tank/Pump Assembly:

The PCS-25 and PCS-15 come with an optional stainless steel soak tank (“Soak

Tank”) and a UL approved submersible agitation pump. The “on/off” switch for

the Soak Tank is located on the lower left hand corner of the lid.

Prior to turning the agitation tank on:

1) Place the stainless steel tank along the left hand side wall of the working surface,

2) Turn the PCS-25/PCS-15 on by depressing the green “on” switch.

3) As the solvent begins to flow, use the cleaning brush and/or nozzle to fill the

stainless steel soak tank until it covers the pump.

4) Once the soak tank is full you can turn on the pump. The agitation pump will

stay on until it is manually turned off.

E. Fluid Nozzle –shutoff.

The fluid nozzle flow can be adjusted or turned off by turning the yellow valve handle at

the nozzle’s base.

F. Filter Differential Pressure Gauge.

The PCS-25/WCS-25 model and the PCS-15 use a pressure gauge to indicate when the

filters need replacing. Replace filters when the gauge reads 40 PSI. Operating system

beyond 40 PSI will not damage the unit, however, the quality of the solvent will degrade

beyond 40 PSI.

G. Fusible Link.

The OSHA Regulated Fusible Link that holds the lid open will release the lid if the

ambient temperature reaches 165F. Never bend the Fusible Link, as it will weaken it.

WARNING! Do not coat or paint fusible link as this may prevent proper

operation. Inspect fusible link annually and replace if corrosion and/or stress is

evident.

J. Leveling Bolts.

The front two legs contain bolts, which are used to minimize any rocking from uneven

floors, and will aid in leveling the unit. The unit must be level to work properly.

VII. CARE AND MAINTENANCE

A. Sump Maintenance.

From time to time the sump of the Parts Washer needs to be pumped clean. The interval

depends on usage. For motor pools this interval is 3-6 months. For weapons cleaning

this interval is 6 months to 1 year. To dump the sump, first remove the hose on the front

right side of the unit, remove the cap and put it either in a bucket or barrel and turn the

hose end valve on. Second, open the yellow valve handle on the main shelf. Third,

move the handle back and forth on the sump pump located on the shelf. Pump the sump

out till the solvent changes color. This usually takes 2-5 gallons. Turn off hose end

valve, yellow handle valve, replace cap and return it to its hangar. Dispose of waste

properly.

B. Canister Lid O-Ring Maintenance

Every time the filters are changed, smear a small amount of petroleum jelly around the

o-ring to keep it lubricated.

WARNING! ALWAYS WEAR GLOVES AND EYE PROTECTION WHEN

HANDLING SOLVENT OR FILTERS.

WARNING! When changing filters, make sure to have something underneath the

used filter as you move it, such as a bucket or oilsorb, to capture any incidental

drips.

C. Changing Filters.

The PCS-25/WCS-25/PCS-15 comes equipped with one or two 5” X 18” filter canisters.

Inside these canisters are 4.5” X 17” filter cartridges. These filters need to be changed

when indicated by the filter status lights or by a 40 PSI reading on the pressure gauge

mounted on the filter canisters. When the gauge or lights indicate a filter change is

needed please follow these steps:

1. Turn all power to the system off.

2. Unplug the unit from wall receptacle.

3. Remove any soak tanks or supplies located on the working surface.

4. To create access to the filter canister lids for the PCS-25/WCS-25 and PCS-15 lift

and remove cutout located on left side of work surface. With the filter wrench provided,

carefully spin off filter canister.

4. With the lid off, carefully pull the used filter out of the canister. Rest the used filter

on the working tray to allow it to fully drain.

5. Place a new (Clarus Stock# WP680SR) filter in the canister.

6. Once the filter is installed, replace lid, screw it in until it seals, no need to tighten

hard.

7. Return lid wrench to its proper location and replace the tray cutouts etc.

D. Replacement Parts.

Part No.

Item

Solvent

1156-5

Solvent - 5 gallon Type II-A

1156-15

Solvent - 15 gallon Type II-A

1156-55

Solvent - 55 gallon Type II-A

250-SS-5

Solvent - 5 gallon Type V

250-55

Solvent - 55 gallon Type V

1157-5

Solvent - 5 gallon Type II-B

1157-55

Solvent - 55 gallon Type II-B

Filters

WP680SR

Solvent Tank Filters (case)

WP680SR-01

Solvent Tank Filter (each)

Options

PCS-0005

Soak Tank Pump

PCS-0029

Control Box for Soak Tank

PCS-0036

Grey Plastic Bin for Pre-Clean

PCS-0037

Pre-Clean Shelf Tray Liner

PCS-0058

Air gun hose

AGOAPP

Onboard Air Pump Option

PCS-0057

Air Gun replacement

Misc. Replacement Parts

PCS-0001

Light Bar Assembly

PCS-0002

Wand Nozzle

PCS-0003

Wand Valve

PCS-0004

Main Solvent Pump

PCS-0006

Misc. 1/2" Hose per foot

PCS-0007

Misc. 3/8" Hose per foot

PCS-0008

Plug

PCS-0010

Hose Clamp Large

PCS-0011

Fusible Link

PCS-0012

Switch (for light/soak pump)

PCS-0013

Main Switch (gr push button)

PCS-0015-36

Molded Cord - 36"

PCS-0015-96

Molded Cord - 96"

PCS-0016

Fuse Holders (rectangular grey)

OC-1294

Fuse Holder (round black)

PCS-0019

Drain Screen

PCS-0020

PVC Drain Hose Valve

PCS-0022

Guzzler/Sump Pump

PCS-0023

Light Bulb

PCS-0024

Replacement Solvent Brush

PCS-0025

Brush Hose (yellow) 4'

PCS-0026

Fuses

PCS-0027

Lid O-Ring Viton - Filter Canister

PCS-0028

Timer

PCS-0030

Lid Clips

Indice

Altri manuali Clarus Technologies Attrezzature per la pulizia

Clarus Technologies

Clarus Technologies PCS-25 Manuale utente

Manuali Attrezzature per la pulizia popolari di altre marche

Skov

Skov Farm AirClean Manuale

Nilfisk-Advance

Nilfisk-Advance CA 240 Manuale utente

ORBOT

ORBOT LiO Manuale utente

unGer

unGer OmniClean Manuale utente

CENTREGO

CENTREGO Toucan Eco Bio Carry Manuale utente

BANDELIN

BANDELIN SONOREX TECHNIK RM 110 UH Manuale utente

Sealey

Sealey VMA913 Manuale utente

Aztec

Aztec 520-00 Manuale utente

BÖWE

BÖWE P25 Manuale utente

Tunap

Tunap MF 929 Istruzioni per l'uso e l'installazione

RIDGID

RIDGID K-45AF-7 Manuale utente

Aircraft

Aircraft POWERGLIDE Manuale utente

Suevia

Suevia 130.5011 EASYCLEANER Manuale utente

Streamline

Streamline Filterplus MOBI SK Manuale utente

Thermax

Thermax AF2 Manuale utente

IPC

IPC CT15R Manuale utente

i-MO

i-MO Öko 2000 Manuale utente

unGer

unGer Hydro Power Ultra UNP01 Manuale utente