Classe Audio CP-45 Manuale utente

CLASSÉ AUDIO

CP-45

REMOTE CONTROL

BALANCED PREAMPLIFIER

CP-45

OWNER'S MANUAL

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS:

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards

etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an

overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a

live performance.

2. UPGRADABLE SINGLE CIRCUIT DESIGNS:

All Classé products (all preamps and all amps) share exactly the same circuit design philosophy

(excluding moving coil and moving magnet phono circuits). This means all amplifiers and all high

level circuits of the preamps benefit from the same design goals. Similar circuits are then tailored to

different power levels etc. Differences between less expensive models and more expensive models

are parts quality and compliment, power supply extravagance and the amount of filtering etc., as

well as features and packaging.

This means that for years Classé has been constantly sonically fine tuning and technically upgrading

this circuit design and its application, thus reaching a very high level of natural musical enjoyment,

as well as excellent reliability which benefits all models - least expensive, most expensive, preamps

and amplifiers alike.

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:

Choosing the best attainable quality parts and materials combined with the advantages of the two

above-mentioned areas provides Classé owners with years of proven trouble free reliability and

musical enjoyment.

CP-45

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP......................................................... 4

A.C. LINE POWER.................................................................... 5

INPUTS....................................................................................... 6

JUMPER SETTING DIAGRAMS (MC/MM,)....................... 10

OUTPUTS ................................................................................. 12

FRONT PANEL CONTROLS.................................................. 13

WARRANTY ............................................................................ 15

FEATURES AND SPECIFICATIONS.................................... 17

WARRANTY REGISTRATION.............................................. 18

UNPACKING & SET-UP

Your CLASSÉ CP-45 preamplifier has been carefully wrapped in heavy gauge plastic, packed

in semi-rigid foam and contained in a special box. To remove the unit, open and spread the top flaps of

the box. By its sides, lift out the entire unit with foam pieces intact. Remove each foam side by pulling

straight out. Remove the plastic wrap and inspect the unit for any concealed damage. Apart from this

owner's manual, please ensure the following has also been included:

1) DETACHABLE LINECORD.

2) ALLEN KEY FOR TOP COVER.

3) REMOTE CONTROL UNIT (Allen key and Batteries: AAA X 2 included).

4) RESISTOR KIT FOR MOVING COIL GAIN ADJUSTMENT. (with optional phono only)

Please report any damage or missing parts to your dealer promptly.

This preamplifier, being capable of very high gain, must be located in a position free of any

hum-inducing magnetic fields. (This also applies to turntables and interconnect cables.) Positions

adjacent to power amplifiers, A.C line filters, or regulation devices should be avoided. Ideally, a few feet

should separate the preamplifier from the power amplifier. As well, keep low-level interconnect cables

away from the power amp and separate from A.C. line cords.

Heat generated by the preamplifier is negligible. Air space around the unit need not be a

concern.

Check the Serial Number sticker on the back of the unit for the correct operating voltage.

Regardless of voltage, the internal fuse rating should be 1 AMP SLO-BLO.

A.C. LINE POWER

The Classé CP-45 preamplifier has no power switch. Its low power consumption and improved

sonics from always being ON led to the omission of an ON/OFF switch. In fact, while thoroughly

musical shortly after turn-on, the preamplifier will exhibit "sonic growth" during its first 300 hours of

use.

For optimum sonic performance, you should consider the use of the optional CLASSÉ REFERENCE

A.C. LINECORD. Consult your dealer regarding this accessory.

SAFETY FEATURE:

The CP-45 preamplifier is designed with an auto-muting circuit which engages and is indicated

by a FLASHING GREEN LED when the unit is first connected, or after an AC power failure. After 15

seconds the STEADY GREEN LED signals that the unit is in STANDBY mode (Note: MUTE is ON

during STANDBY mode).

This feature will prevent any turn-on surges or unstable output from reaching the power

amplifier and possibly the loudspeakers. Similarly, make sure the MUTE is ON (STEADY GREEN)

again when removing A.C. line power.

CAUTION:

DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS. "FLOATING THE GROUND” OR

DEFEATING THE GROUND ON A 3-PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT ALL

INTERCONNECT CABLES BETWEEN THE ELECTRONICS BEFORE CONNECTING THE A.C. LINECORDS

TO THE WALL OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. SEE ALSO THE

WARRANTY SECTION OF THIS OWNER'S MANUAL.

INPUTS:

The input jacks are clearly marked on the back of the CP-45. The following inputs are

provided: PHONO/AUX, VIDEO, CD, TUNER, BALANCED, and TAPE.

PHONO/AUX

The CP-45 preamplifier can be configured as a PHONO unit by installing the optional

internal phono board onto the main board. The PHONO and AUX inputs share the same pair of RCA

input jacks. The GND screw is located next to PHONO/AUX input jacks. The following steps

should be performed to remove or install the phono board.

1) Make sure MUTE is ON (Steady GREEN)

2) Disconnect A.C. linecord from the wall outlet.

3) Remove the top cover with the Allen key supplied.

PHONO CONFIGURATON: (installation of phono board)

4) Locate and replace mounting screws 1, 2, 3 with the stand-offs supplied.

5) Remove jumpers J1, J2 (see fig.1, Page 9)

6) Install and secure the phono board using screws in step 4, make sure all connectors are

properly aligned. Set MC/MM jumpers if required (see fig-2a, 2b page 10). Replace the top

cover.

AUX CONFIGURATION: (removal of phono board)

7) Reverse steps 4, 5, and 6, make sure jumpers J1 and J2 are reinstalled for AUX

operation. (see fig.1a, page 9)

PHONO INPUT:

When switched to PHONO the input can accommodate both magnetic and moving coil

cartridges of various outputs. In the MC position, gain of the Moving Coil stage is factory preset at

16dB which matches perfectly with most typical MC cartridges. With the resistor kit included, the

gain can be adjusted to 18dB, 23dB, or 28dB, in order to optimize system gain, and lower noise

while using other less typical MC cartridges. (Note: The MC gain is in addition to the standard MM

gain of 42dB). To change the MC gain, proceed as follows:

1) Perform steps 1, 2, and 3 as mentioned above.

2) Locate R104 and R204 (see fig.2, Page 10), which are the MC gain setting resistors for the

LEFT and RIGHT channels respectively. Remove the resistors and replace them with newly selected

ones, according to the following chart:

GAIN COLOR CODED RESISTOR (or) NUMERICAL RESISTOR

Standard 13 dB (Brown,White,Blue,Brown) 1961

18 dB (Orange,Grey,Orange,Brown) 3831

23 dB (Purple,Green,Black,Brown) 7501

28 dB (Brown,Red,Purple,Red) 1272

5) Having completed the resistor changes, replace the top cover.

AUX INPUT:

When selected (see AUX configuration) the AUX input serves as an additional high level

input, accommodating additional sources such as VIDEO, CD, TUNER, etc..

VIDEO, CD, TUNER:

These are all high level inputs sharing exactly the same characteristics, and may be

interchanged if so desired.

BALANCED The BALANCED INPUT is a true differential high level input, wired as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

It may be used with CD players that have a balanced output, or any other high level balanced

sources.

TAPE IN

The TAPE IN of the CP-45 preamplifier should be connected to the LINE OUT or TAPE

OUT of the tape deck. The TAPE input does not appear on the selector switch. It is activated by the

TAPE switch. (See FRONT PANEL CONTROLS: TAPE SWITCH.)

Indice

Altri manuali Classe Audio Amplificatore

Classe Audio

Classe Audio CP-500 Manuale utente

Classe Audio

Classe Audio CAM-200 Manuale utente

Classe Audio

Classe Audio CA-M600 Manuale utente

Classe Audio

Classe Audio SSP-75 Manuale utente

Classe Audio

Classe Audio C-303 Manuale utente

Classe Audio

Classe Audio CP-700 Manuale utente

Classe Audio

Classe Audio C-601 Manuale utente

Classe Audio

Classe Audio CA-201 Manuale utente

Classe Audio

Classe Audio CA-M400 Manuale utente

Classe Audio

Classe Audio CA-5100 Manuale utente

Classe Audio

Classe Audio CA-100-101 Manuale utente

Classe Audio

Classe Audio CA-2200 Manuale utente

Classe Audio

Classe Audio Delta Series Manuale utente

Classe Audio

Classe Audio CA-300 Manuale utente

Classe Audio

Classe Audio CP-800 Manuale utente

Classe Audio

Classe Audio CRCD Manuale utente

Classe Audio

Classe Audio CA-M400 Manuale utente

Classe Audio

Classe Audio P-151 Manuale utente

Classe Audio

Classe Audio CAP-2100 Manuale utente

Classe Audio

Classe Audio CAV-150 Manuale utente

Classe Audio

Classe Audio CT-2300 - V1.1 Manuale utente

Classe Audio

Classe Audio CP-800 Manuale utente

Classe Audio

Classe Audio DR 25 Manuale utente

Classe Audio

Classe Audio CA-2100 - 3 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente