Clear One DIALOG 10 Manuale utente
Quick-Start Guide
QSG-0130-001v1_DIALOG10USB_2021_09_21
DIALOG®10 USB Wireless Receiver
DIALOG 10 USB Wireless System Receiver
QSG-0130-001v1_DIALOG10USB_2021_09_21
Quick-Start Guide
Contents:
Setting up the system ............................................................................................................................ 3
Box Contents ................................................................................................................................ 3
Set Up ........................................................................................................................................... 3
Syncing the Transmitters with the Receiver ........................................................................................ 4
Receiver Front Panel and Back Panel ................................................................................................. 4
Receiver Module ................................................................................................................................... 5
2
DIALOG 10 USB Wireless System Receiver
QSG-0130-001v1_DIALOG10USB_2021_09_21
Quick-Start Guide
DIALOG 10 USB Receiver:
(Qty. 1) .... Receiver Base Unit
(Qty. 2) .... 2.4 GHz Dipole Antennas
(Qty. 1) .... 12’ USB-A to USB-C Cable
(Qty. 1) .... 6’ USB-A to USB-Micro Cable
3
Setting Up ClearOne DIALOG® 10 Wireless Receiver:
Packing List: Inspect your shipment carefully and verify contents. If the shipment shows signs
of damage, retain original boxes and packing material for inspection by the carrier, and contact them
immediately. ClearOne is not responsible for product damage incurred during shipment.
The contents of the DIALOG 10 USB Wireless Receiver package are listed below (For DIALOG 20
Transmitters, please see the DIALOG 20 Transmitters Quick Start Guide).
Box Contents:
1. Charge the Transmitters:
Transmitters include rechargeable batteries. Install the
batteries, connect the USB-A to USB-Micro cable to the
transmitter and plug it into a USB power source to charge
the batteries (12 hrs is required for a full charge).
2. Mount the Receiver:
Mount receiver at least 10’ away from computer and WiFi.
The receiver can be shelf, wall, or ceiling mounted.
3. Connect the Dipole Antennas:
Connect the Dipole Antennas to the receiver. Position the
antennas at approximately 45 degrees. Keep an open line
of sight between the transmitter and receiver antennas.
4. Connect the Receiver to a Computer:
Use the cable supplied with the receiver to connect the
receiver to a computer. The USB-A to USB-C Cable
provides power and audio.
DIALOG 20 Wireless Transmitters are compatable with DIALOG 10 and DIALOG 20 Receivers.
USB-A to USB-Micro Cable
USB-A to USB-C Cable
ON/OFF
IR USB
OR
45° 45°
10’
Wi-Fi
Set Up:
DIALOG 10 USB Wireless System Receiver
QSG-0130-001v1_DIALOG10USB_2021_09_21
Quick-Start Guide
13
24
Receiver Front and Back Panels:
4
Front Back
1. Antenna “A” TNC Connector
2. Receiver Module (See pg. 5)
3. Antenna “B” TNC Connector
4. USB-C Type Connector
Syncing Transmitters with Receiver:
1. Simultaneously, press the two buttons on the bottom of the receiver module. ”SCANNING” shows
on the receiver’s display for 5 to 10 seconds followed by “SYNCING”.
a. To sync a Boundary Mic or Podium Mic:
While the receiver shows “SYNCING”, Press and hold the “Mute” button, power on the
transmitter and then release the “Mute” button.
b. To sync a Handheld or Beltpack:
While the receiver shows “SYNCING”, Press and hold the “Select” button, power on the
transmitter and then release the “Select” button.
Both the transmitter and receiver display will read “SYNC PASS” when the sync is successful.
2. Repeat the procedure if the receiver display shows “SYNC FAIL”.
3. Check the audio.
“SCANNING” will only be displayed if auto-scan is enabled.
DIALOG 10 USB Wireless System Receiver
QSG-0130-001v1_DIALOG10USB_2021_09_21
Quick-Start Guide
5
Receiver Module and LCD:
1 & 2 ... Sync Buttons: Pressed at the same time, sends SYNC signal to transmitter (See pg. 4).
3 ......... Status LED:
l GREEN .................. The channel is ON and un-muted.
l RED ....................... The channel is OFF.
ll FLASHING RED .... Encryption key mismatch or, two transmitters are synced to the
same Receiver. Solution: Re-sync the transmitter with the receiver.
l AMBER .................. The receiver is muted.
STATUS
SELECT
FUNCTION
(SYNC)
IR
BATTERY AUDIO
SLOT 1
CH 1 ON AES128
RF Bars
Audio Level
Battery Level
ID Labeling
Encryption
Status Indicator (text corresponds to LED):
RF Channel Assignment
12
Antenna Diversity
ON = Green LED
OFF = Red LED
MUTE = Amber LED
KEY = Flashing Red LED
(“KEY” = mismatched encryption key)
1 3 2
DIALOG 10 USB Wireless System Receiver
QSG-0130-001v1_DIALOG10USB_2021_09_21
Quick-Start Guide
Other product names may be registered trademarks of their respective owners who do not necessarily endorse ClearOne or ClearOne’s products. All rights reserved.
Information in this document subject to change without notice. © 2021 ClearOne. QSG-0130-001 ClearOne_DIALOG10_QuickStartGuide-V1.0 September 21, 2021
Headquarters
5225 Wiley Post Way
Suite 500
Salt Lake City, UT.
84116
US & Canada
Tel: 801.975.7200
Toll Free: 800.945.7730
Fax: 801.303.5711
International
Tel: +1.801.975.7200
Email: [email protected]
Sales
Tel: 801.975.7200
Email: [email protected]
Tech Support
Tel: 801.974.3760
Email: [email protected]
Antenna Design
Tel: 386.361.8134
Email: [email protected]
Indice
Altri manuali Clear One Ricevitore
