Climax VST-1818 Manuale utente
September 30, 2017
Table of Contents
1. INTRODUCTION ________________________________________________________________________ 2
1.1. FUNCTION OVERVIEW ____________________________________________________________ 2
2. APPLICATION OVERVIEW_______________________________________________________________ 3
2.1. IDENTIFYING THE PARTS __________________________________________________________ 3
2.2. PACKAGE CONTENT _____________________________________________________________ 5
2.3. THE POWER SUPPLY _____________________________________________________________ 5
2.4. SYSTEM REQUIREMENTS __________________________________________________________ 5
3. GETTING STARTED _____________________________________________________________________ 6
3.1. HARDWARE INSTALLATION_________________________________________________________ 6
3.2. SOFTWARE INSTALLATION ________________________________________________________ 12
3.3. FACTORY RESET _______________________________________________________________ 15
4. CONNECTING TO WEBPAGE____________________________________________________________ 17
5. IP CAMERA____________________________________________________________________________ 19
5.1. IMAGE TUNING_________________________________________________________________ 19
5.2. MOTION DETECTION ____________________________________________________________ 19
5.3. TIME STAMP __________________________________________________________________ 23
5.4. STREAM SETTING ______________________________________________________________ 24
5.5. RECORDED FILES ______________________________________________________________ 25
5.6. ALARM SETTING _______________________________________________________________ 26
6. NETWORK SETTING ___________________________________________________________________ 28
6.1. NETWORK____________________________________________________________________ 28
6.2. WIRELESS (WIFI MODELS ONLY) ___________________________________________________ 29
6.3. UPNP_______________________________________________________________________ 31
7. SYSTEM SETTING _____________________________________________________________________ 32
7.1. CHANGE PASSWORD ____________________________________________________________ 32
7.2. REPORT _____________________________________________________________________ 33
7.3. MEDIA UPLOAD ________________________________________________________________ 34
7.4. XMPP ______________________________________________________________________ 35
7.5. DATE &TIME__________________________________________________________________ 36
7.6. DYNAMIC DNS ________________________________________________________________ 37
7.7. FIRMWARE ___________________________________________________________________ 38
7.8. FACTORY RESET _______________________________________________________________ 39
7.9. BACKUP &RESTORE____________________________________________________________ 40
7.10. SYSTEM LOG__________________________________________________________________ 41
7.11. LOGOUT _____________________________________________________________________ 42
7.12. REBOOT _____________________________________________________________________ 42
8. HISTORY ______________________________________________________________________________ 43
8.1. EVENT LOG___________________________________________________________________ 43
8.2. REPORTED EVENTS_____________________________________________________________ 43
9. NETWORK VIDEO RECORDER__________________________________________________________ 44
10. REMOTE ACCESS TO THE IP CAMERA __________________________________________________ 47
10.1. HOME PORTAL SERVER__________________________________________________________ 47
10.2. PORT FORWARDING_____________________________________________________________ 48
11. CONNECTING TO CLIMAX CONTROL PANELS___________________________________________ 53
11.1. LEARNING THE IP CAMERA INTO THE CONTROL PANELS __________________________________ 53
11.2. SURVEILLANCE AND SETTING______________________________________________________ 56
11.3. OPERATION___________________________________________________________________ 60
11.4. HOME PORTAL SERVER__________________________________________________________ 63
12. APPENDIX_____________________________________________________________________________ 63
12.1. CONTACT ID EVENT CODE________________________________________________________ 63
2
1. Introduction
The VST-1818 IP Camera provides a quick and accurate surveillance solution to protect
your surroundings. You can watch these live-stream videos through MJPG or H264
formats via Local Area Network, or online remotely using port forwarding, or via the
Climax Home Portal™Server for you to easily keep track of the safety of your homes or
businesses.
VST-1818 IP Camera can be further integrated into your current Climax Security Control
Panels to form a complete security system, and capture video when an alarm is
activated.
VST-1818 IP Camera series includes the following models with different functions and
spec:
Indoor/Outdoor
Wi-Fi
IR LED
IR Cut Filter
VST-1818
Indoor
No
Yes
Yes
VST-1818-WI
Indoor
Internal Antenna
Yes
Yes
VST-1818-WE
Indoor
External Antenna
Yes
Yes
VST-1818L-WI
Indoor
Internal Antenna
No
No
VST-1818LR-WI
Indoor
Internal Antenna
Yes
No
VST-1818SLIM
Indoor
No
No
No
1.1. Function Overview
The VST-1818 IP Camera includes a variety of functions that can be adjusted to suit
different necessities. Below is an overview of the functions of the IP Camera:
- Alarm-triggered video recording that includes Pre-alarm recording to see how alarm
was triggered. Please see 5. IP Camera, 5.6. Alarm Setting.
- 24-hour HD video recording. Please see 9. Network Video Recorder.
- Remote access/control on Climax Home Portal Server on a web-enabled device.
Please see 10. Remote Access to the IP Camera, 10.1. Home Portal Server.
- Remote video using Port Forwarding. Please see 10. Remote Access to the IP
Camera, 10.2. Port Forwarding.
- Surveillance when complementing with Control Panels. Please see 11. Connecting
to the Climax Control Panels, 11.2. Surveillance and Setting.
- Remote access/control complementing with Control Panels on Climax Home Portal
Server on a web-enabled device. Please see 11. Connecting to the Climax
Control Panels, 11.4. Home Portal Server.
3
2.Application Overview
2.1. Identifying the Parts
VST-1818/VST-1818WE/VST-1818WI/VST-1818L-WI/VST-1818LR-WI
1. IP Camera Lens
2. Microphone
3. Optical Sensor
4. Power LED (Green)
On: powered
Off: unpowered
5. Warning LED (Red)
Flashes for 2-3 seconds: Activating WPS protocol
Flashes 3 times: WPS pairing successful
Flashes twice: Enter/exit privacy mode
On: The IP Camera is in privacy mode
6. Internet-Connection LED (Blue)
On: connected to internet (wired or wireless)
Off: disconnected from internet
Flashes for 5 minutes: The IP Camera is in learning mode
Flashes quickly: The IP Camera is streaming or recording.
7. Speaker
8. WPS Button
9. Privacy Button
Press and hold for 2 seconds until warning LED flashes twice, let go to enter or exit privacy
mode
Press and hold for 10 seconds to enter learning mode
Press and hold for 6 seconds to exit learning mode.
4
10.Expandable Micro SD card slot
Compatible with Micro SD card up to 32GB storage capacity (Micro SD card is not
included by factory default)
11.Ethernet Cable Port
12.DC Jack (5V DC, 2A input)
13.Camera Stand Mounting Hole
14.Antenna (VST-1818WE model only)
VST-1818 SLIM
1. WPS Button
2. Privacy Button
Press and hold for 2 seconds until warning LED flashes twice, let go to enter or exit privacy
mode
Press and hold for 10 seconds to enter learning code
Press and hold for 6 seconds to exit learning mode
3. Microphone
4. Power LED (Green)
On: powered
Off: unpowered
5. Warning LED (Red)
Flashes for 2-3 seconds: Activating WPS protocol
Flashes 3 times: WPS pairing successful
Flashes twice: Enter or exit privacy mode
On: The IP Camera is in privacy mode
6. Internet-Connection LED (Blue)
On: connected to internet (wired or wireless)
Off: disconnected from internet
Flashes for 5 minutes: The IP Camera is in learning mode.
Flashes quickly: The IP Camera is streaming or recording.
7. IP Camera Lens
1
2
3
4
5
6
7
8
9
10
11
1
2
7
5
8. Expandable Micro-SD slot
Compatible with Micro SD card up to 32GB storage capacity (Micro SD card is not
included by factory default)
9. Ethernet Cable Port
10.DC Jack (5V DC, 2A input)
11.Camera Stand Mounting Hole
2.2. Package Content
The VST-1818 IP Camera is packed in a white box that includes:
-An Ethernet cable
-A power supply (5V DC 1A adapter)
-An IP Camera Stand
-Installer CD
2.3. The Power Supply
An AC power adapter is required to connect to a wall outlet. Be sure only to use an
adapter with the appropriate AC voltage rating to prevent component damage. A 5V DC
output and 1A adapter is generally used to power the IP Camera.
2.4. System Requirements
The system requires a TCP/IP network environment.
To install the CD Wizard, your computer must have:
Microsoft Windows 98, ME, NT4.0, 2000, XP, Vista, 7 or 8 operating system. A
Mac or Linux based machine is also compatible.
DirectX 9.0 or later Internet Explorer 6.x or later
CD-ROM drive
Pentium III CPU 500 MHz or higher, or equivalent AMD
128 MB RAM
Graphics card: 32 MB RAM
6
3.Getting Started
Read this section of the manual to learn how to set up your VST-1818 IP Camera and
program system settings over the Web page.
With a valid internet connection, this system can bring you the freedom to access and
control your IP Camera anywhere and anytime in the world.
3.1. Hardware Installation
Step 1. Remove any plastic cover and prepare the enclosed adapter and Ethernet
cables.
With Wired Connection:
Step 2. Find a suitable location to mount the IP Camera.
Step 3. Plug in the enclosed Ethernet cable.
<NOTE>
If the IP Camera is to complement with a Control Panel, connect the IP Camera
and the Control Panel to the same router to learn the IP Camera into the Control
Panel. Please refer to 11. Connecting to the Climax Control Panels if you
wish to increase the functionality of the IP Camera.
Step 4. Plug in the adapter.
With Wi-Fi (Wireless) Connection:
Please refer to the 6. Network Setting. 6.2. Wireless on how to connect to the Wi-Fi
Network.
7
Using a Camera Stand
Below displays the 3 part design of the camera stand:
The Base is attached to the surface where
the stand is mounted
The Shaft is connected between
the base and the head.
The Head connects the IP Camera
to the whole camera stand
Below outlines the steps to mount the IP Camera to a surface.
Step 1. Find a surface to mount the camera stand. Locate the 2 mounting holes of the
Base and use them as template, mark the surface.
Step 2. Apply wall plugs if fixing onto plaster or brick. Screw the Base onto the surface.
8
Step 3. Attach the Head to the Shaft by rotating the Head clockwise onto the Shaft.
Step 4. Attach the Shaft onto the Base by rotating the Shaft clockwise onto the Base.
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Climax Telecamera IP
