CNB LKC1050IR Manuale utente

LKC1050IR

Network Pancake Dome

Camera

Rev.1.1 (Sep. 2014) 2

Caution

Any changes or modifications in construction of this device which are not explicitly

approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generate, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into and outlet on a circuit different from that to which

the receiver is connected

 Consult the dealer or an experienced radio/TV technician for help.

Directions

Be careful not to cause any physical damage by dropping or throwing LKC1050IR. Especially

keep the device out of reach from children.

Do not disassemble LKC1050IR. No After Service is assumed when disassembled.

Use only the power adapter provided with LKC1050IR.

Be careful to prevent moisture or water penetration into the unit. Particular attention is

needed when installing LKC1050IR. The screw holes for the installation screws and pipe

should be maintained water tight during the whole life time of the product.

All the electrical connection wires running into the unit should be prepared so that water from

the outside cannot flow into the unit through the surface of the wires. Penetration of the

moisture through the wire for extended period can cause malfunction of the unit or

deteriorated image.

Rev.1.1 (Sep. 2014) 3

Contents

1. Introduction .............................................................................................................................................. 4

1.1. Overview ............................................................................................................................................. 4

1.2. Specification ........................................................................................................................................ 5

1.3. Applications of LKC1050IR .................................................................................................................. 6

2. Product Description ................................................................................................................................. 7

2.1. Contents ............................................................................................................................................. 7

2.2. Product Preview .................................................................................................................................. 7

2.3. Physical description............................................................................................................................. 8

2.3.1. External View ............................................................................................................................ 8

2.3.2. Dimension ................................................................................................................................. 8

2.3.3. Inside ........................................................................................................................................ 9

2.3.4. External Connector .................................................................................................................. 10

3. On Site Installation ................................................................................................................................. 11

4. Getting Started ....................................................................................................................................... 12

4.1. PC Requirement................................................................................................................................ 12

4.2. Quick Installation Guide ..................................................................................................................... 12

4.2.1. Connect PC and LKC1050IR to network. ................................................................................. 12

4.2.2. Install IP installer and set IP parameters on LKC1050IR .......................................................... 13

4.2.3. Remote video connection to LKC1050IR ................................................................................. 16

4.2.4. Additional settings through connection to the Admin Page ....................................................... 17

5. Trouble Shooting ................................................................................................................................... 18

5.1. No power is applied ........................................................................................................................... 18

5.2. Cannot connect to the Video ............................................................................................................. 19

5.3. Windows Vista or Windows 7............................................................................................................. 20

5.4. Technical Assistance ......................................................................................................................... 23

Rev.1.1 (Sep. 2014) 4

1. Introduction

1.1. Overview

LKC1050IR is multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and

hardware technology in pancake housing. It enables real time transmission of video of up to 1080P. Remote

clients can connect to LKC1050IR for the real time video data through various client solutions running on PC or

smart device.

LKC1050IR is specialized in video transmission which economic and practical products removing sensor, replay,

etc and the videos can be only available in the field and place where needed.

Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the owner to reduce TCO (Total Cost of

Ownership) by reducing on-site wiring works for the installation.

Rev.1.1 (Sep. 2014) 5

1.2. Specification

Camera

Image sensor Progressive scan 1/2.9 inch CMOS 2.0M pixels

Full resolution 1,920 x 1,080 pixels (Full HD)

Min. illumination 0.2Lux (Color, DSS On), 0.00 Lux (IR LED On)

S/N Ratio 50dB or more

White Balance Auto

DSS Supported

WDR Off/ON

Lens Built-in Fixed Lens f=3.7mm F2.5

Day & Night Supported (TDN & IR LED)

IR LED 12EA (850nm, 45°) Max. 12m

Video

Compression method Simultaneous Dual Codec (H.264 / MJPEG)

Resolution 1920x1080@30fps

Multi-Profile Streaming - 3 simultaneous video profiles

- Select the codec type, resolution and frame rates for each profile.

Intelligent Bit-Rate Control Hybrid Bit Rate control (VBR+CBR)

Image Setting Text overlay, Privacy mask

Motion detection 3 regions

Video Output Select NTSC/PAL 1.0Vp-p (RCA type on board, 75Ω, composite)

Network

Network Protocol

- IPv4/v6, TCP, UDP, IGMP, ICMP, ICMPv6, ARP, RARP, PPPoE, RTCP

- RTP, RTSP, SDP, HTTP, HTTPS, SMTP, FTP, DHCP, UPnP

- NTP, DNS, DynDNS, SOCKS

Dynamic IP Supported (through management server)

Security - User ID & Password protection, IP address filtering

- HTTPS encryption, Digest Authentication, User Access Log

Streaming method

- RTSP streaming with proprietary format for control informations

- Standard RTSP streaming

- HTTP streaming

External Terminals

LAN 10/100BaseT LAN (auto MDIX)

Power DC 12V input

Factory Reset Supported

Rev.1.1 (Sep. 2014) 6

Alternate Power

Standard PoE IEEE802.3af Supported

Alarm & Event

Intelligent Video Motion Detection

Alarm Triggers Intelligent Video

Alarm Events video file upload(FTP), still Image(Email)

Alarm Buffer (Video) configurable Pre-alarm (5~10 sec) & Post-alarm (10~30 sec)

Client Software

NVR2 64ch@D1 (free of charge)

Mobile App. Android, iOS (free of charge)

Miscellaneous

Operating Temperature -10



C ~ 40



Operation Humidity 8~80% RH

Power DC 12V Max. 5W

Dimensions Ø122mm(4.8”) x 55mm(2.1”)

Weight 195g

Approvals FCC, CE, KCC, RoHS

Package information IP camera, CD (User’s guide, Software…)

Optional Items

Adapter DC 12V, 2A

1.3. Applications of L

 Small Office, Home environment, Personal user.

 Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,

military, etc.)

 Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)

 Weather and environmental observation

Rev.1.1 (Sep. 2014) 7

2. Product Description

2.1. Contents

The product package contains followings :

Contents Description Remarks

LKC1050IR IP camera LKC1050IR main unit

CD Software & User’s Guide

Accessory Wall Anchors 3ea, Screw 3ea

2.2. Product Preview

LKC1050IR IP-Installer CMS Software (NVR2)

IP Camera PC software to allocate an IP

address to the IP Camera

PC software to view and record the

streaming data transmitted from IP

camera.

(Simultaneous support of up to 64

IP cameras@D1)

Rev.1.1 (Sep. 2014) 8

2.3. Physical description

Figure 2-1. External view of LKC1050IR

Figure 2-2. Dimension

Rev.1.1 (Sep. 2014) 9

 Network (LAN)

100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). LED on the Ethernet connector shows

the status of LKC1050IR as the followings:

- Status LED (It will be lit in green or red depending on the status)

① Green : Green color indicates that the camera is in normal operation mode. Continuous green

indicates that data transmission is possible.

Figure 2-3. Status LED

 Factory Default Switch

Factory default switch is provided for returning the IP camera to factory default state. Unscrew the cover

to access the switch. Press the switch about 5 seconds while power is applied to return to factory default

state

Figure 2-4. Factory Default Switch

Status LED

Factory Default Switch

Rev.1.1 (Sep. 2014) 10

Figure 2-5. External Connector

 Power : Power input for supplying 12V DC power.

Caution : If LKC1050IR is powered by PoE, do not plug in DC Jack with active DC

power into DC power connector.

 Network (LAN)

100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). LED on the Ethernet connector shows

the status of LKC1050IR as the followings:

Network (LAN)

POWER

Indice

Altri manuali CNB Telecamera di sicurezza

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente