CNET CNAP-711 Manuale utente

11Mbps Wireless LAN Access Point

CNAP-711 USER GUIDE

TABLE OF CONTENTS

1INTRODUCTION...............................................................................................................5

1.1 The 11Mbps Wireless Access Point.....................................................................5

1.2 Features..............................................................................................................5

2PACKAGE CONTENTS ....................................................................................................6

3ACCESS POINT CONFIGURATION.................................................................................7

3.1 Hardware installation...........................................................................................7

3.2 Software installation ............................................................................................7

3.3 Configuring the Access Point...............................................................................9

3.3.1 Connecting to the AP....................................................................................9

3.3.2 FIND AP.....................................................................................................10

3.3.3 Connect AP................................................................................................10

3.4 Configuration.....................................................................................................12

3.4.1 Change Password......................................................................................15

3.4.2 Encryption (WEP).......................................................................................15

3.4.3 Configure “Advance” (Expert setting).........................................................19

APPENDIX:............................................................................................................................23

GLOSSARY............................................................................................................................24

4SPECIFICATIONS...........................................................................................................26

INFORMATION TO USER

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables

when connecting to computer or peripheral devices) any changes or modifications not

expressly approved by the party responsible for compliance could void the user's authority to

operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Regulatory

The wireless LAN ACCess Point must be installed and used in strict accordance with the

manufacturer’s instructions. This device complies with the following radio frequency and safety

standards.

USA - Federal Communications Commission (FCC)

This device complies with Part 15 of FCC Rules. Operation is subject to the following two

conditions:

•This device may not cause harmful interference.

•This device must accept any interference that may cause undesired operation.

Europe - R&TTE Directive

This device complies with the specifications listed below:

•ETS 300-826 General EMC requirements for Radio equipment.

•ETS 300-328 Technical requirements for Radio equipment.

•EN60950 Safety requirements for Radio equipment.

EU Countries not intended for use

The ETSI version of this device is intended for home and office use in Austria, Belgium,

Denmark, Finland, France (with Frequency channel restrictions). Germany, Greece, Ireland,

Italy, Luxembourg, Netherlands, Portugal, Spain, Sweden and United Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states Iceland,

Liechtenstein, Norway and Switzerland.

1 Introduction

1.1 The 11Mbps Wireless Access Point

The 11Mbps WLANAccess Point is a long-range, high performance LAN product, which

provides Access Point services to a 2.4 GHz RF network and bridges to an Ethernet backbone.

This solution offers fast, reliable wireless connectivity with considerable cost savings over

wired LANs (which include long-term maintenance overhead for cabling.) Just install enough

wireless access points, plug WLAN card into User notebook or WLAN adapter into User

desktop PC, and start networking.

Using this device in conjunction with WLAN cards or adapters, User can create an instant

network that integrates seamlessly with 10Mbps Ethernet LANs. Moreover, moving or

expanding User network is as easy as moving or installing additional access points - no wire!

1.2 Features

•IEEE 802.11b Direct Sequence spread spectrum high rate compatible.

•High data rate 11/5.5/2/1 Mbps.

•WEP encryption/decryption is accomplished on the fly.

•Fragmentation and Reassembly.

•Wired Equivalent Privacy Algorithm (WEP) (64 bits/128 bits)

•Power Management.

•Passive/Active scan. Long/Short preamble.

•RTS/CTS handshake.

•Duplicate Detection and Recovery.

•Authentication Algorithm (Open System, Shared Key).

•Dual external antennas supporting diversity.

•Easy installation.

2 Package Contents

•One Access Point.

•One setup Utility CD-ROM( User Guide on CD).

•One power adapter.

•Quick Installation Guide.

QuickInstallationGuide

3 Access Point Configuration

3.1 Hardware installation

Connect the LAN RJ45 port of the Access Point (AP) to a PC, Notebook or User existing

network (using Ethernet Cat. 5 cable) and connect the DC power adaptor to the AP.

Note: To configure the AP, User can use either the wired Ethernet connection or a Wireless

LAN device.

3.2 Software installation

Insert the setup CD into the CD-ROM drive of the PC or Notebook used for configuration.

There are two methods to install the AP utility software:

(a). Auto run: an auto run program will display on the screen. Click “Install Software”

(b). Alternately, please click “start\run\D:\AP\utility\setup.exe (D:\ is the default letter for the

CD-ROM drive). The InstallShield Wizard will guide User through the installation in the

following menu sequence:

 Click “Next”.

 Choose the default installation file path and click “Next” or click “Change” to select a

different location.

 Click“Install”

 Click “Finish” to complete the Software installation.

3.3 Configuring the Access Point

3.3.1 Connecting to the AP

Click Start/Program/SNMP.

Note: The default IP address of the AP is “192.168.0.254”. For connecting to theAP, please

assign an IP address (in the range of 192.168.0.1 ~ 192.168.0.253) to the network device used

for configuration (Wireless or wired LAN card).

The setup program will scan the network for the Access Points installed:

When done, the present settings information of all the Access Points on the network will be

displayed on the screen as below:

There are two “buttons” displayed by the program, “FIND AP” and “Connect AP”. Their

functions are explained below:

3.3.2 FIND AP

Clicking on “FIND AP”, the utility will automatically rescan for all the Access Points (based on

IP address) on the network and display their current settings.

3.3.3 Connect AP

Clicking on “Connect AP”, the utility will connect to the selected AP and an “Input

PASSWORD” dialogue box will be displayed requesting password entry for theAP being

configured:

Indice

Altri manuali CNET Punto di accesso wireless

CNET

CNET CWA-854 Manuale utente

CNET

CNET CNWR-811P Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente