Code 3 CD5031 Manuale utente

Page 1 of 24

Installation and Operation Instructions

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/

or death to those you are seeking to protect!

Do not install and/or operate this safety product unless you have read and understood the safety information

contained in this manual.

1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to

ensure the safety of emergency personnel and the public.

2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical

connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,

which can cause personal injury and/or severe vehicle damage, including re.

4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of

the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without

losing eye contact with the roadway.

5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag

deployment area may reduce the e󰀨ectiveness of the air bag or become a projectile that could cause serious personal injury or death.

Refer to the vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable

mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.

6. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator

should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),

people, vehicles or other obstructions.

7. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.

Never take the right-of-way for granted. It is the vehicle operator’s responsibility to be sure they can proceed safely before entering an

intersection, drive against tra󰀩c, respond at a high rate of speed, or walk on or around tra󰀩c lanes.

8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws

regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The

manufacturer assumes no liability for any loss resulting from the use of this warning device.

Specications:

Input Voltage: 12 - 24VDC

Max Current: CD5031XX 0.6A @ 12VDC

Temp. Range: -40ºC to 65ºC

-40ºF to 149ºF

CD5031 SURFACE MOUNT/STUD

MOUNT,12LED, DUAL COLOR

Page 2 of 24

Installation and Mounting:

Wiring Instructions:

CD5031XX

RED Wire: Positive, Colors 1 & 3 (need to add

2A fuse)

WHITE Wire: Positive, Colors 2 & 4 (need to add

2A fuse)

BLACK Wire: Negative

BLUE Wire: Pattern Select to Negative

BLUE Wire to Positive: DIM

YELLOW Wire: Synchronized Function

(Up to 8 units can be Synchronized)

IMPORTANT! This unit is a safety device and it must be connected

to its own separate, fused power point to assure its continued

operation should any other electrical accessory fail.

CAUTION!

When drilling into any vehicle surface, make sure that the

area is free from any electrical wires, fuel lines, vehicle

upholstery, etc. that could be damaged.

Note: It is recommended to isolate wires/blunt wires that were cut or not used.

The light head has a small round hole covered with vent membrane that must face downward when mounting the light head.

Figure 1

10in-lbs max.

screw torque

10in-lbs max.

screw torque

Figure 2

Page 3 of 24

Flash Patterns:

Phase Operation:

Phase 1 (Ph1) ashes simultaneously with Ph1

Phase 2 (Ph2) ashes simultaneously with Ph2

Ph1 alternates with Ph2

(Up to 8 units can be Synchronized)

Apply BLUE TO BLACK wire:

-Less than 1 sec. for next pattern

-Between 1-3 sec for previous pattern

-Between 3-5 sec. for factory default pattern

-More than 5 sec. for pattern 12 (CD5031XX)

Page 4 of 24

Dual Color Flash Pattern Chart

Pattern

LED Color

1 & Color 3

Red Wire

LED Color

2 & Color 4

White Wire

LED Color 1 & Color

3 LED Color 2 &

Color 4 Red & White

Wire

FLASH PATTERN

SYNCH

SAE J595 CAT 13 ECE R65

RED AMBER BLUE WHITE RED AMBER BLUE RED AMBER BLUE

1-Default 1

SAE/T13 Single 75FPM Ph1 Color 1 Synchro-

nous Color 3 yes Class 1 Class 1 Class 1 Class 1 ClassB ClassB ClassB N/C N/C N/C

2 2

SAE/T13 Single 75FPM Ph2 Color 1 Synchro-

nous Color 3 yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B N/C N/C N/C

SAE/T13 Single 75FPM Ph1 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

SAE/T13 Single 75FPM Ph2 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

1-Default 5

SAE/T13 Single 75FPM Ph1 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B N/C N/C N/C

2 6

SAE/T13 Single 75FPM Ph2 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B N/C N/C N/C

3 3 7

SAE/T13 Single 75FPM (Color 1 Synchronous

Color 3) Alternately(Color 2 Synchronous Color

4)(Phase 1) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

4 4 8

SAE/T13 Single 75FPM (Color 1 Synchronous

Color 3) Alternately(Color 2 Synchronous Color

4) (Phase 2) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

5 5 9

SAE/T13 Single 75FPM (Color 1 Alternately

Color 2) Alternately(Color 3 Alternately Color 4) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

6 10

Single 375FPM Ph1 Color 1 Synchronous

Color 3 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

711

Single 375FPM Ph2 Color 1 Synchronous Color

3 yes yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

12 Single 375FPM Ph1 Color 1 Alternately Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

13 Single 375FPM Ph2 Color 1 Alternately Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

6 14

Single 375FPM Ph1 Color 2 Synchronous

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

7 15

Single 375FPM Ph2 Color 2 Synchronous

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

8 8 16

Single 375FPM (Color 1 Synchronous Color

3) Alternately(Color 2 Synchronous Color 4)

(Phase 1) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

9 9 17

Single 375FPM (Color 1 Synchronous Color

3) Alternately(Color 2 Synchronous Color 4)

(Phase 2) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

10 10 18

Single 375FPM (Color 1 Alternately Color 2)

Alternately (Color 3 Alternately Color 4) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

11 19

SAE/T13 Double 75FPM Ph1 Color 1 Synchro-

nous (Color 3) yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B N/C N/C N/C

12 20

SAE/T13 Double 75FPM Ph2 Color 1 Synchro-

nous (Color 3) yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B N/C N/C N/C

SAE/T13 Double 75FPM Ph1 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

SAE/T13 Double 75FPM Ph2 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

11 23

SAE/T13 Double 75FPM Ph1 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B N/C N/C N/C

12 24

SAE/T13 Double 75FPM Ph2 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 Class B Class B Class B N/C N/C N/C

13 13 25

SAE/T13 Double 75FPM (Color 1 Synchronous

Color 3) Alternately

(Color 2 Synchronous Color 4) (Phase 1) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

14 14 26

SAE/T13 Double 75FPM (Color 1 Synchronous

Color 3) Alternately

(Color 2 Synchronous Color 4) (Phase 2) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

15 15 27

SAE/T13 Double 75FPM (Color 1 Alternately

Color 2) Alternately (Color 3 Alternately Color 4) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

Page 5 of 24

Dual Color Flash Pattern Chart (Continued)

Pattern

LED Color

1 & Color 3

Red Wire

LED Color

2 & Color 4

White Wire

LED Color 1 & Color

3 LED Color 2 &

Color 4 Red & White

Wire

FLASH PATTERN

SYNCH

SAE J595 CAT 13 ECE R65

RED AMBER BLUE WHITE RED AMBER BLUE RED AMBER BLUE

16 28

ECER65/SAE Double 120FPM Ph1 Color 1

Synchronous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C Class 1 Class 1

Class

17 29

ECER65/SAE Double 120FPM Ph2 Color 1

Synchronous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C Class 1 Class 1

Class

ECER65/SAE Double 120FPM Ph1 Color 1

Alternately Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

ECER65/SAE Double 120FPM Ph2 Color 1

Alternately Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

16 32

ECER65/SAE Double 120FPM Ph1 Color 2

Synchronous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C Class 1 Class 1

Class

17 33

ECER65/SAE Double 120FPM Ph2 Color 2

Synchronous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C Class 1 Class 1

Class

18 18 34

ECER65/SAE Double 120FPM (Color 1 Syn-

chronous Color 3)Alternately (Color 2 Synchro-

nous Color 4)(Phase 1) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

19 19 35

ECER65/SAE Double 120FPM (Color 1 Syn-

chronous Color 3)Alternately (Color 2 Synchro-

nous Color 4)(Phase 2) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

20 20 36

ECER65/SAE Double 120FPM (Color 1 Alter-

nately Color 2)Alternately (Color 3 Alternately

Color 4) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

21 37

SAE/T13 Triple 75FPM Ph1 Color 1 Synchro-

nous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

22 38

SAE/T13 Triple 75FPM Ph2 Color 1 Synchro-

nous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

SAE/T13 Triple 75FPM Ph1 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

SAE/T13 Triple 75FPM Ph2 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

21 41

SAE/T13 Triple 75FPM Ph1 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

22 42

SAE/T13 Triple 75FPM Ph2 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

23 23 43

SAE/T13 Triple 75FPM (Color 1 Synchronous

Color 3) Alternately(Color 2 Synchronous Color

4)(Phase 1) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

24 24 44

SAE/T13 Triple 75FPM (Color 1 Synchronous

Color 3) Alternately(Color 2 Synchronous Color

4)(Phase 2) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

25 25 45

SAE/T13 Triple 75FPM (Color 1 Alternately

Color 2) Alternately (Color 3 Alternately Color 4) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

26 46

SAE/T13 Quad 75FPM Ph1 Color 1 Synchro-

nous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

27 47

SAE/T13 Quad 75FPM Ph2 Color 1 Synchro-

nous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

SAE/T13 Quad 75FPM Ph1 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

SAE/T13 Quad 75FPM Ph2 Color 1 Alternately

Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

26 50

SAE/T13 Quad 75FPM Ph1 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

27 51

SAE/T13 Quad 75FPM Ph2 Color 2 Synchro-

nous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

28 28 52-Default

SAE/T13 Quad 75FPM (Color 1 Synchronous

Color 3) Alternately (Color 2 Synchronous Color

4)(Phase 1) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

29 29 53

SAE/T13 Quad 75FPM (Color 1 Synchronous

Color 3) Alternately (Color 2 Synchronous Color

4)(Phase 2) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

30 30 54

SAE/T13 Quad 75FPM (Color 1 Alternately

Color 2) Alternately (Color 3 Alternately Color 4) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

Page 6 of 24

Dual Color Flash Pattern Chart (Continued)

Pattern

LED Color

1 & Color 3

Red Wire

LED Color

2 & Color 4

White Wire

LED Color 1 & Color

3 LED Color 2 &

Color 4 Red & White

Wire

FLASH PATTERN

SYNCH

SAE J595 CAT 13 ECE R65

RED AMBER BLUE WHITE RED AMBER BLUE RED AMBER BLUE

31 55

ECER65/SAE Quad 120FPM Ph1 Color 1

Synchronous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

32 56

ECER65/SAE Quad 120FPM Ph2 Color 1

Synchronous Color 3 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

ECER65/SAE Quad 120FPM Ph1 Color 1

Alternately Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

ECER65/SAE Quad 120FPM Ph2 Color 1

Alternately Color 4 yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

31 59

ECER65/SAE Quad 120FPM Ph1 Color 2

Synchronous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

32 60

ECER65/SAE Quad 120FPM Ph2 Color 2

Synchronous Color 4 yes Class 1 Class 1 Class 1 Class 1 N/C N/C N/C N/C N/C N/C

33 33 61

ECER65/SAE Quad 120FPM (Color 1 Synchro-

nous Color 3) Alternately (Color 2 Synchronous

Color 4)(Phase 1) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

34 34 62

ECER65/SAE Quad 120FPM (Color 1 Synchro-

nous Color 3) Alternately (Color 2 Synchronous

Color 4)(Phase 2) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

35 35 63

ECER65/SAE Quad 120FPM (Color 1 Alter-

nately Color 2) Alternately (Color 3Alternately

Color 4) yes N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

8 64

Modulation (Color 1 Synchronous Color 3) Alter-

nately (Color 2 Synchronous Color 4) no N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

9 65

2 Double,2 Quad (Color 1 Synchronous Color 3)

Alternately (Color 2 Synchronous Color 4) no N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

10 66

4 Single,2 Triple (Color 1 Synchronous Color 3)

Alternately (Color 2 Synchronous Color 4) no N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

11 67

1Doube 1Triple 1Quad (Color 1 Synchronous

Color 3) Alternately (Color 2 Synchronous

Color 4) no N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

12 36 68 Steady burn-Color 1 & 3 no N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

36 69 Steady burn-Color 2 & 4 no N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C

Page 7 of 24

Notes

Page 8 of 24

An ECCO SAFETY GROUP™ Brand

ECCOSAFETYGROUP.com

10986 North Warson Road, St. Louis, MO 63114 USA

Technical Service USA (314) 996-2800

[email protected]

CODE3ESG.com

The CD5031XX series are factory tested and approved. If any of the functions of the device fail to operate, please check the following:

PROBLEM QUESTION CAUSE SOLUTION

Product does not

function when

turned on

Are LEDs

functioning

properly?

Yes a. Plug is loose or disconnected. a. Reconnect plug.

b. Poor ground connection b. Reconnect ground.

No a. Power has been disconnected. a. Check connections at the battery and plug.

Troubleshooting:

Product Returns:

If a product must be returned for repair or replacement*, please contact our factory to obtain a Return Goods Authorization Number (RGA

number) before you ship the product to Code 3®, Inc. Write the RGA number clearly on the package near the mailing label. Be sure you use

su󰀩cient packing materials to avoid damage to the product being returned while in transit.

*Code 3®, Inc. reserves the right to repair or replace at its discretion. Code 3®, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of products requiring

service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products returned to sender after the service has been rendered.

Manufacturer Limited Warranty Policy:

Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are avail-

able from the Manufacturer upon request). This Limited Warranty extends for Sixty (60) months from the date of purchase.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICA-

TIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE

MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WAR-

RANTY.

Exclusion of Other Warranties:

MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY

OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EX-

CLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE

LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.

Remedies and Limitation of Liability:

MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR UNDER ANY

OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE, AT MANUFACTURER’S DISCRETION, THE

REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PROD-

UCT. IN NO EVENT SHALL MANUFACTURER’S LIABILITY ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO

THE MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL PURCHASE.

IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY

DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IM-

PROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT

TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF

ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty denes specic legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdic-

tions do not allow the exclusion or limitation of incidental or consequential damages.

920-0923-00 Rev. C

Warranty:

Page 9 of 24

Installation and Operation Instructions

IMPORTANTE Lea todas las instrucciones antes de la instalación y el uso del producto. Instalador: se debe entregar este manual al usuario

¡ADVERTENCIA!

Si no sigue las instrucciones del fabricante a la hora de instalar o usar el producto, pueden producirse daños materiales, y lesiones

graves o incluso mortales a aquellos que pretende proteger.

No instale ni use este producto de seguridad sin haber leído y comprendido la información sobre seguridad

incluida en este manual.

1. Para garantizar la seguridad del personal de emergencias y la de las personas a las que este intenta proteger, es esencial una instalación

correcta, combinada con la formación del operador en el uso, cuidado y mantenimiento de los dispositivos de alerta de emergencia.

2. Los dispositivos de alerta de emergencia a menudo requieren tensiones eléctricas o corrientes de entrada altas. Tenga cuidado cuando

manipule conexiones eléctricas.

3. Este producto debe conectarse a tierra correctamente. Una conexión a tierra incorrecta o unas conexiones eléctricas cortocircuitadas

pueden provocar arcos de corriente alta, lo que puede ocasionar lesiones personales o daños graves en el vehículo, incluso un incendio.

4. La colocación e instalación adecuadas son vitales para el buen funcionamiento de este dispositivo de advertencia. Instale este producto

de forma que permita un rendimiento óptimo del sistema y de que los controles estén situados de modo que el operador pueda

alcanzarlos cómodamente y manejar el sistema sin perder en ningún momento el contacto visual con la calzada.

5. No instale este producto ni coloque los cables en la zona de despliegue de un airbag. Si el equipo se monta o coloca en la zona de

despliegue de un airbag, el airbag puede perder ecacia o el equipo puede salir despedido, lo que podría causar lesiones graves o incluso

mortales. Consulte el manual del propietario del vehículo para conocer la zona de despliegue de los airbags. El usuario u operador son

responsables de determinar una posición de montaje adecuada que garantice la seguridad de todos los ocupantes del vehículo, y deben

evitar zonas que puedan provocar golpes en la cabeza.

6. Es responsabilidad del operador del vehículo asegurarse todos los días de que todas las características de este producto funcionan

correctamente. Durante su uso, el operador del vehículo debe asegurarse de que no haya componentes del vehículo (como los maleteros

o puertas del habitáculo abiertos), personas, vehículos u otros obstáculos que bloqueen la señal de alarma.

7. El uso de este o cualquier otro dispositivo de advertencia no garantiza que los conductores puedan respetar la señal de alarma o

reaccionar ante ella ni que vayan a hacerlo. Nunca dé por hecho que tiene prioridad de paso. Es responsabilidad del operador del

vehículo asegurarse de que puede continuar de forma segura antes de entrar en una intersección, conducir en sentido contrario,

responder a una gran velocidad o caminar por los carriles con tráco o cerca de ellos.

8. El uso de este equipo está reservado exclusivamente a personal autorizado. El usuario es responsable de conocer y acatar todas las

Especicaciones:

Tensión de

entrada:

12-24 V CC

Corriente de

trabajo:

CD5301XX 0,6 A a 12 V CC

MONTAJE EN SUPERFICIE/EN PERNO

DE LA SERIE CD5031, CON 12 LUCES

Page 10 of 24

Instalación y montaje:

Instrucciones de cableado:

CD5031XX

Cable ROJO: Positivo, colores 1 y 3 (requiere un

fusible de 2 A)

Cable BLANCO: Positivo, colores 2 y 4 (requiere un

fusible de 2 A)

Cable NEGRO: Negativo

Cable AZUL: Selección de patrón negativa

Cable AZUL con selección

positiva: ATENUADO

Cable AMARILLO: Función sincronizada

IMPORTANTE Esta unidad es un dispositivo de seguridad, y debe

conectarse a una toma independiente de alimentación con fusible

para garantizar su funcionamiento continuo si fallase cualquier

PRECAUCIÓN:

Cuando taladre cualquier supercie del vehículo, asegúrese

de que no exista el riesgo de dañar cables eléctricos, tubos

de combustible, tapicería de vehículo, etc.

Nota: Se recomienda aislar los cables, despuntados o no, que se hayan cortado o no se utilicen.

El cabezal de luz tiene un pequeño oricio redondo cubierto con una membrana de ventilación que debe mirar hacia abajo al

montar el cabezal de luz.

Figura 1

Par de apriete

máximo

de 10 lb-pulg

Par de apriete

máximo

de 10 lb-pulg

Figura 2

Altri manuali per CD5031

Indice

Lingue:

Altri manuali Code 3 Rack e supporto

Code 3

Code 3 C3900 Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente