Code Alarm PROFESSIONAL SERIES Manuale utente

1CA1B6 / FLRS 4280922 Owners rev A.

IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is

applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR

SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.

PROFESSIONAL

SERIES

Owner’s Guide

For Model:

CA1B6

Flashlogic FLRS

RF Upgrade Kit

Table of Contents

Using Your Remote Control .......................................................3

Remote Start Valet Mode............................................................3

Transmitter Programming..........................................................4

Replacing Remote Control Batteries ........................................4

3CA1B6 / FLRS 4280922 Owners rev A.

Remote Starting Your Vehicle

To activate the remote start, press and release the button 2 times within 2

seconds. The vehicle will start and run the predetermined time set up during

installation (5 to 60 minutes selectable).

Remote Start Shutdown

Press and hold the button for 3 seconds to turn the vehicle off. Pressing the

vehicle’s brake will also shutdown the remote start.

Entering the Vehicle while it is Running via Remote Vehicle Start

1. Unlock the vehicle’s doors. (If equipped, press and release the button

2 times within 2 seconds while the vehicle is remote started)

2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!

3. Insert the key into the ignition switch and turn to the ON or RUN

position.

4. Press the brake pedal. The remote vehicle starter will disengage and

the vehicle will operate normally.

Preheating or Precooling the Vehicle’s interior

Before exiting the vehicle, set the temperature controls to the desired setting and

operation. After the system starts the vehicle, the heater or air conditioner will

activate and heat or cool the vehicle’s interior to your setting.

Using Your Remote Control

Remote Start Valet Mode

Enter / Exit Valet mode for systems using an Flashlogic FLRS kit.

1. Cycle ignition ON ve times [5x OFF/ON] rapidly. (complete this step

within 7 seconds)

2. Wait, LED 1 (on the FLRS kit) will turn solid RED for 2 seconds.

3. Turn ignition to OFF position.

4. Valet Mode Programming Procedure completed.

NOTE: In Valet Mode, the remote starter is not functional. On units with keyless entry,

lock and unlock will remain functional. To exit valet mode: repeat steps 1 to 4.

1 Way Remote Control, CAT1LR:

The battery (model CR2032) inside each remote control should last approximately 1

year under normal use. When the battery becomes weak you will notice the remote

control range (the distance from the vehicle the remote control will work) deteriorate

and the small LED on the remote control will dim. To replace the battery in the remote

control:

1. Unsnap and disassemble the halves of the remote control.

2. Remove the old battery, observing the +/- symbols on the battery

and replace with new CR2032 battery.

3. Reassemble the halves of the remote control.

4. Test operation of the remote control.

Replacing Remote Control Batteries

Transmitter Programming

1. Turn the ignition ON.

2. Press and hold the valet/override button located on the antenna.

3. Within 10 seconds the LED’s will begin to ash.

4. Press 1 button of each transmitter you wish to program, the LED’s will

ash to conrm each transmitter.

5. Turn the ignition OFF

NOTE: This system has 1 button programming which programs all channels of the

system.

NOTE: The system will hold up to 4 transmitters in memory, programming a 5th

transmitter will erase the oldest transmitter in memory.

5CA1B6 / FLRS 4280922 Owners rev A.

Voxx Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of

Industry Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that

may cause undesired operation.

Warning!

Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Altri manuali per PROFESSIONAL SERIES

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Code Alarm Avviamento remoto

Code Alarm

Code Alarm PROFESSIONAL SERIES Manuale utente

Code Alarm

Code Alarm CA1BTW5 Manuale utente

Code Alarm

Code Alarm CA611 Manuale utente

Code Alarm

Code Alarm CSM-3 Manuale utente

Code Alarm

Code Alarm Professional ca5054 Manuale utente

Code Alarm

Code Alarm Professional Series CA 5050 Manuale utente

Code Alarm

Code Alarm CA 6150 Manuale utente

Code Alarm

Code Alarm CA 1055 Manuale utente

Code Alarm

Code Alarm ca6554 Manuale utente

Code Alarm

Code Alarm ca4B5 Manuale utente

Code Alarm

Code Alarm PC 4400 Manuale utente

Code Alarm

Code Alarm ca5153 Manuale utente

Code Alarm

Code Alarm CA-430 Manuale utente

Code Alarm

Code Alarm CA 5150 Manuale utente

Code Alarm

Code Alarm CA 411 Manuale utente

Code Alarm

Code Alarm Professional Series CA 4050 Manuale utente

Code Alarm

Code Alarm ca5554 Professional series Manuale utente

Code Alarm

Code Alarm Professional Series CA 4050 Manuale utente

Code Alarm

Code Alarm CA 421 Manuale utente

Code Alarm

Code Alarm CA 2050 Manuale utente

Code Alarm

Code Alarm CA-520A Manuale utente

Code Alarm

Code Alarm ca 1051 Manuale utente

Code Alarm

Code Alarm ca5554 Professional series Manuale utente

Code Alarm

Code Alarm CA 5053 Manuale utente

Manuali Avviamento remoto popolari di altre marche

AstroStart

AstroStart 803U Manuale utente

Durite

Durite 0-649-20 Manuale

EINHELL

EINHELL BT-PS 1000 Manuale

Linear

Linear ACCESS AK-21 Specifiche tecniche

Soundstream

Soundstream TARANTULA RS.2 Manuale utente

Jaycar Electronics

Jaycar Electronics MB3752 Manuale utente

Ultra Start

Ultra Start 72 Series Manuale utente

ADS

ADS FLASHLOGIC FLRSVW1 Manuale utente

Selecta

Selecta JS012 Manuale utente

Black Widow Security

Black Widow Security BW RAS 400 Manuale utente

Vector

Vector Power City DK080706 Supplemento

Ozito

Ozito OJS-800 Manuale utente

Profi-Partner

Profi-Partner 46387 Manuale utente

EZ STARTER

EZ STARTER EZ-45 Manuale utente

Viper

Viper 4204 Manuale utente

Essex Electronics

Essex Electronics KE-1701 Manuale utente

EINHELL

EINHELL EGS 3600 Manuale

Rooboost

Rooboost RB-1750WP Manuale utente