Cognex In-Sight SnAPP Series Manuale utente

In-Sight®SnAPP Series

Quick Reference Guide

2023 September 01

Revision: 23.1.0.6

Precautions

To reduce the risk of injury or equipment damage, observe the following

precautions when you install the Cognex product:

lThe safety of any system incorporating this product is the responsibility of

the assembler of the system.

lDo not install Cognex products where they are exposed to environmental

hazards such as excessive heat, dust, moisture, humidity, impact,

vibration, corrosive substances, flammable substances, or static electricity.

lRoute cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

lDo not expose the image sensor to laser light. Image sensors can be

damaged by direct, or reflected, laser light. If your application requires

laser light that might strike the image sensor, use a lens filter at the

corresponding laser wavelength. For suggestions, contact your local

integrator or application engineer.

lThis product does not contain user-serviceable parts. Do not make

electrical or mechanical modifications to product components.

Unauthorized modifications can void your warranty.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lInclude service loops with cable connections.

lEnsure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius is tighter than 10X the cable

diameter.

lThis device should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purposes only and can change without

notice.

Symbols

The following symbols indicate safety precautions and supplemental information:

WARNING:This symbol indicates a hazard that could cause death, serious personal injury or

electrical shock.

CAUTION:This symbol indicates a hazard that could result in property damage.

Note: This symbol indicates additional information about a subject.

Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.

Accessories

You can purchase the following components separately. For a list of options and

accessories, contact your local Cognex sales representative.

Mounting Brackets

Accessory Product Number Illustration

Pivot mounting bracket DM100-PIVOTM-01

Tilted angle pivot bracket DMBK-DMPIVOT-00

Cables

Note: Cables are sold separately.

Accessory Product Number Illustration

Ethernet Cable, X-coded M12-8 to

RJ-45

CCB-84901-2001-xx (straight, xx specifies length:

2m, 5m, 10m, 15m, 30m)

Ethernet Cable, X-coded M12-8 to

RJ-45

CCB-84901-2002-xx (right-angled, xx specifies

length: 2m, 5m, 10m)

Accessory Product Number Illustration

Ethernet Cable, Robotic X-Coded

M12-8 to RJ-45

CCB-84901-2RBT-xx (straight, xx specifies length:

2m, 5m, 10m)

X-Coded to A-Coded Ethernet cable

adapter, 0.5 m

CCB-M12X8MS-XCAC

Power and I/O Breakout Cable, M12-

12 to Flying Lead

CCB-PWRIO- xx (straight, xx specifies length: 5m,

10m, 15m)

Power and I/O Breakout Cable, M12-

12 to Flying Lead

CCB-PWRIO-xxR (right-angled, xx specifies length:

5m, 10m, 15m)

I/O Module Cable M12-12 to DB15 CCB-PWRIO-MOD-xx (xx specifies length: 2m, 5m)

RS-232 Connection Cable CCB-M12xDB9Y-05

I/O Extension Cable CKR-200-CBL-EXT

Setting Up Your In-Sight Vision Sensor

Read this section to learn how the vision sensor connects to its standard

components and accessories.

Note:

lCables are sold separately.

lIf a standard component is missing or damaged, immediately contact

your Cognex Authorized Service Provider (ASP) or Cognex

Technical Support.

CAUTION:All cable connectors are keyed to fit the connectors on the vision

sensor. Do not force the connections or damage may occur.

Vision Sensor Layout

The image and table below shows the elements of the vision sensor.

Number Description

1 Power I/O Breakout cable connector

2 USB-C slot (with plastic cover)

3Ethernet connector

4Illumination LEDs

Number Description

5 LED aimer

6 Trigger button

Note: The Trigger Button is not supported.

7 Tune button

Note: The Tune Button is not supported.

8Indicator LEDs

Number Description

9Power LED indicator

10 Train status/Trigger status LED indicator

11 Good/bad inspection LED indicator

12 Communication LED indicator

13 Error LED indicator

Indice

Altri manuali Cognex Lettore di codici a barre

Cognex

Cognex DataMan 8700 DX Manuale utente

Cognex

Cognex DATAMAN 500 Manuale utente

Cognex

Cognex DataMan 370 Series Istruzioni operative

Cognex

Cognex DataMan Istruzioni operative

Cognex

Cognex DataMan 300 Series Manuale utente

Cognex

Cognex DataMan 8700 Manuale utente

Cognex

Cognex DataMan 470 Series Manuale utente

Cognex

Cognex DataMan 470 Series Manuale utente

Cognex

Cognex DataMan 60 Series Manuale utente

Cognex

Cognex DataMan 360 Series Manuale utente

Cognex

Cognex DataMan 8072 DL Manuale utente

Cognex

Cognex DataMan 503 Manuale utente

Cognex

Cognex DataMan 200 Manuale utente

Cognex

Cognex DataMan DM474 Manuale utente

Cognex

Cognex DataMan 280 Series Manuale utente

Cognex

Cognex DataMan 8700 Manuale utente

Cognex

Cognex DataMan 475 Verifier Manuale utente

Cognex

Cognex DataMan 8072 DL Manuale utente

Cognex

Cognex DataMan 7550 Manuale utente

Cognex

Cognex DATAMAN 500 Manuale utente

Cognex

Cognex Advantage 182 Series Istruzioni di montaggio

Cognex

Cognex DataMan 8072 Verifier Manuale utente

Cognex

Cognex DataMan 260 Series Manuale utente

Cognex

Cognex DataMan 8600 Verifier Series Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente