ComMarker B3 Manuale utente
Laser Marking Machine
B3
Manual
Security Statement
Before using the laser engraving machine, please read this safety guide carefully.
It mentions situations that require special attention and includes warnings of unsafe practices that can cause damage to
your property or even endanger your personal safety.
1 Laser Safety
•The machines use Class Ⅳlasers. The lasers are very powerful and can cause eye injuries and burn the skin. It is
recommended to wear laser goggles when using the laser engraver.
•Avoid exposing your skin to Class Ⅳlaser beams, especially at close range
•Teens must be supervised by parents while using the machine.
•Do not touch the laser engraving beam while it is switched on.
2 Material Safety
•Do not engrave materials with unknown properties.
•Materials recommended:
Metal, including stainless steel, aluminum, bronze, brass, alloy, etc,
Plastics, including PP, PE, ABS, etc.
3 Use Safety
•It is forbidden to point the laser to people, animals or any combustible object, whether it is in working condition or not.
•Use this laser engraving device only in accordance with all applicable local and national laws and regulations.
•Use this device only in accordance with this instruction manual and engraving software manual.
•DO NOT leave this device unattended during operation. Cut off all power to the machine and contact either our customer
service or repair service if anything seems to be working abnormally.
•Any untrained personnel who might be near the device must be informed the danger of the machine before operation
4 Electric Safety
•Only use this device with a compatible and stable power supply with less than 5% fluctuation in its voltage.
•Turn on the power to this device when it is well grounded.
•ONLY use this device with one hand at a time. The laser is powered by an extremely high voltage connection and placing
two hands on the machine at one time during operation has the potential to create a closed circuit with the human body,
resulting in electrical shock.
•The area around this laser engraver device should be kept dry, well ventilated, and environmentally controlled to keep the
ambient temperature between 40–95°F (5–35°C). The ambient humidity should not exceed 70%.
Note:
1) Adjusting the focus is a necessary prerequisite for laser engraving, please refer to step 4 of the manual before
engraving.
2) Make sure to remove the plastic protective cover of the field lens before engraving to avoid damage to the field lens
caused by laser burning.
Product Structure
Assembly of Machine
1. Place the parts on the table 2. Put the lifting pole upright
3. Fasten the pole with the screws 4. Put the laser head on the supporting shelf of
the pole
5. Fasten the screws to fix the laser head 6. Connect the laser machine with the computer,
and switch on the machine
Operation Instructions
1. Install the driver
Note: please conduct the following operation before installing the driver
1) The machine is on; (Notice, Pls take off the lens)
2) Data cable connected;
3) Copy and paste the files of the USB disk to the computer desktop;
1.Right-click "this PC", click "Manage"
2.Click "Device Manager", find “USBLMCV2”or “Unknown
Device” in“Other devices”or “Universal Serial Bus devices”
3.Right-click “Unknown device” or “USBLMCV2”and
"Update driver"
4.Select "Browse My Computer for Drivers"
1
2
3
4
5.Find the corresponding file with window system in the
USB drive, click OK
6.Click "Install"
7.Click “finish” if it is successful
8.It will display "BJJCZ Device" in Device Manager
Noted: *It is recommended to copy and paste the files of the USB disk to the computer desktop or other computer
disks.
*If the driver installation is unsuccessful, please refer to FAQ 1
5
6
7
8
2. Open the software
Open the USB folder, open the "EZCAD for ComMarker" folder, and select the 150mm folder if the lens is 150mm. Open
the software “EZCAD2”. You can enter "text", import "picture" or "vector file" as shown in the figure below. It is
recommended to select the text to test first.
3. Import the correction file
Select "Parameter (F3)", tick "Use Correct File", select the file ending in .cor in the USB flash drive (or have been copied to
the computer disk), and click "OK (确认)".(if your machine is mopa, pls read page 11)
4. Adjust the focus
Press up or down button to lift or lower the laser head until the three red light point overlap, which is the best focal point.
The measuring focal length of this machine is ___________ mm, and the measuring distance is the length from the bottom
line of the laser head to the surface of the engraving material. This parameter is measured manually, and each device has
different focal lengths due to changes in laser sources and field lenses.
Note: Before the machine is out of the factory, we have done red light correction (for your lens). At the position where
the two red light spots overlap, the laser emits the strongest light. However, due to transportation reasons, the focus
point of the red lights you received may shift, and the focus point would not be the best focal length.
Please operate as the following steps:
1.Place the stainless steel test plate on the machine table
2.lift up or down the laser head to the best focus point
according to the number in handwriting above
3.Turn on the machine, connect the computer with the
machine
4. Import the “TEXT” for testing, select the default
parameters, and tick the “continuous part” button.
5. Press “red (F1)” to ensure it’ll mark on the test material.
Click “mark”, and the laser would be continuously marking
6. Meanwhile, lift or lower the laser head and observe the
obvious change of intensity of the laser beam. Stop when
the it works with the strongest laser
7.At this time, loosen the screws for the two beams of the
auxiliary red light
8. Manually adjust the relative position of the red light
dots to make them overlap. And tighten the screws
5.Marking test
Place the test engraving material on the machine. Click "Red (F1)", the area shown by the red light is the marking area. Tick
“Default Parameters". Click "Mark (F2)" to start marking.
Parameters
Voltage
110V
Laser Type:
Fiber
Working Area
70mmx70mm/ 110mm x 110mm/ 150mmx150mm/ 175mmx175mm/
200mm x 200mm
Wavelength
1064nm
Marking Speed:
0- 15000mm/min
Accuracy
0.01mm
Graphic Format Supported:
AI/PLT/JPG/DXF.etc
System Supported
Window7/8/10/11
Cooling Type
Air Cooling
Output Power
20w-smart/ 30W/ 50W/ 60W
Laser source
MAX / Raycus / JPT Mopa
Weight (KG):
10.5kg-20w-smart/ 21.5KG-30W、50W、60W
Questo manuale è adatto per i seguenti modelli
2
Indice
