SCULPFUN S6 Manuale utente
English
Deutsche
Français
Italiano
Español
Polskie
Preview the main parts
7、X Beam set
8、Laser module
1、Back Beam
2、Front Beam
6、Mainboard support
3、Left Beam
4、Right Beam
5、Foot
support
5
5
Main Unit：
1、Back Beam
2、Front Beam
3、Left Beam
4、Right Beam
5、Foot support
6、Mainboard support
7、X Beam set
8、Laser module
Note!
This picture is the total
picture after the
assembly is completed.
In the subsequent steps,
if you are unclear about
the installation details,
you can check it with
this picture.
Note! Pay attention to the details of
the scale line on the lower left corner
beam, refer to this picture to judge
whether the installation is correct
Step 1 Assemble the back, left and right beams
11
2
4
3
3
4
2
Back Beam
Back Beam
Left Beam
Right Beam
Note：
1、Find the required tool and screw model before starting assembly: T-
shaped hexagon wrench,Step1 Screw bag, left/right/back frame beams,
tripod*2.
2、Notice label position! There is label paper on the beam, and the label
is placed in the position as shown on the left.
3、When assembling, ensure that the edges of the beam and the tripod
are neatly parallel and tight.
4、The picture on the left is the frame after Step1 is assembled.
Back Beam
Left Beam
Right Beam
1 2 3 4
M5*18
M5*30
M5*18
M5*8
Notice label !
Step 2 Assemble X beam set and front beam
1
1
2 Front Beam
3
3
4
4
5
5
Motherboard
tripod
Tripod
Assembly steps：
1、Push the X beam assembly into the U-shaped frame, paying
attention to the direction of white logo !
2、Required components: tripod*1, motherboard tripod, front frame
beam, Step3 screw pack, T-shaped hexagonal wrench.
3、Assemble the tripod, main board tripod, and front frame beam
according to the right figure, install them in the order of step 12345,
and tighten the screws 1/3/4/5 in the order.
1 3 4 5
M5*18
M5*30
M5*8
M5*18
Step 3 Install the belt
Installation steps:
Install the belt to the position shown in the figure,note:
1. The belt should be installed in the direction of the arrow in the figure
above.
2. The tooth pattern of the belt faces downwards and engages with the
gears.
3. There should be an extra part of the belt at one end for easy pulling and
tightening of the belt. The extra belt can be cut off after the T-nut is fixed
in the next step4.
Step 4 Install T nut
1
1
2
2
1
2
Do not tighten the T nut, pull
the belt with your hand to
make the belt tight
With the belt tightened, tighten
the screws to keep the long side
of the T-nut perpendicular to the
groove.
Put the T nut into the groove, the long
side is parallel to the groove, Strongly
press the T nut while rotating the wrench
clockwise to make the long side of the T
nut perpendicular to the groove
Put the T nut into the groove, the long side is
parallel to the groove, Strongly press the T nut
while rotating the wrench clockwise to make the
long side of the T nut perpendicular to the groove
Tighten the screws and keep
the long side of the T-nut
perpendicular to the groove.
Installation steps:
1. First install the T-nut on one side as shown
in the figure.
2. Install the other end of the T-nut on the
other side, and note that the long side of the
T-nut is perpendicular to the groove after
installation. After the installation is complete,
the belt is in a tight state. For extra belts, if
you are not familiar with the use of belts, we
suggest that you do not cut off the extra belts
Step 5 Install laser module and data cable
1
Tighten the screw
by hand to control
the tightness
X
Y
Laser
Laser
Y
X
1
If the tightness of the roller and the guide rail
is not suitable, use a wrench to turn it up and
down to control the tightness of the roller
and the guide rail
Question: How to judge the tightness of the belt?
Answer: After the installation is completed, tilt
the machine at 45°, if the X beam can slide
down slowly under the action of gravity, it is
appropriate.
2
Installation steps:
1. Install the laser module on the back panel
by hand-tightening the screws, and control
the tightening of the screws by hand
2. Connect the Y, X and laser terminals of
the data cable to the machine interface as
shown in the figure.
3. Use cable ties to fix the data cable on the
fixing hole to protect the data cable.
3
Data Cable
The focusing principle of SCULPFUN laser module
20mm
Focusing principle:
1、The focal length of the SCULPFUN
laser module is fixed and cannot be
changed .
2、The specific position of the laser
focus is 20mm directly below the
edge of the aluminum alloy shell of
the laser module.
3、We provide a 20mm measuring
aluminum column to help find the
laser focus.
4、When the laser is focused on the
surface of the engraved object, it will
exert its maximum engraving effect.
20mm
measuring
aluminum
column
the surface of the engraved object
edge of the
aluminum
alloy shell
measuring
aluminum
column
How to quickly focus laser on the surface of the sculpture
1、Place the measuring
aluminum column on the
surface of the engraved
object, loosen the
thumbscrew behind the laser
module, and slide the laser
module on the measuring
aluminum column
2、When the laser module is
in good contact with the
measuring aluminum column,
tighten the thumb screw on
the back of the laser module
3、After fixing the laser
module, remove the
measuring aluminum column
and start engraving
20mm
Customer Service:
Ø For detailed warranty policy,please visit
our official website at: www.sculpfun3d.com
Ø For Laser Engraver technical support and
service,please email:
support@sculpfun3d.com
Manufacturer: Shenzhen Sculpfun
Technology Co., Ltd.
Address: 1411, Building D, Longguang Jiuzuan Business
Center South, Daling Community, Minzhi Street, Longhua
District, Shenzhen, Guangdong, China 518131
Note：This Manual is just for installation, For how to
use laserGRBL software, how to show the position of
the engraving pattern, and how to set the engraving
parameters of different materials, please scan the QR
code or visit the website www.sculpfun3d.com to
download the User Manual.
Scanner APP:
QR Code Reader
/Barcode Scanner
or any APP with scanner
Sculp your fun !
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali SCULPFUN Incisore
