SCULPFUN S10 Manuale utente
English
Deutsche
Français
For Italian/Spanish/Polish
and user manual please
scan
Preview the main parts
7、X Beam set
8、Laser module
1、Back Beam
2、Front Beam
6、Mainboard support
3、Left Beam
4、Right Beam
5、Foot
support
5
5
Main Unit：
1、Back Beam
2、Front Beam
3、Left Beam
4、Right Beam
5、Foot support
6、Mainboard support
7、X Beam set
8、Laser module
9、Air tube
Note!
This picture is the total
picture after the
assembly is completed.
In the subsequent steps,
if you are unclear about
the installation details,
you can check it with
this picture.
Note! Pay attention to the details of
the scale line on the lower left corner
beam, refer to this picture to judge
whether the installation is correct
9、Air tube （inner 7.5mm ）
Step 1 Assemble the back, left and right beams
1 1
2
4
33
4
2
Back Beam（Notice label on bags !）
Back Beam
Left Beam Right Beam
Note：
1、Find the required tool and screw model before starting assembly: T-
shaped hexagon wrench,Step1 Screw bag, left/right/back frame beams,
tripod*2.
2、Notice label position! There is label paper on the beam, and the label
is placed in the position as shown on the left.
3、When assembling, ensure that the edges of the beam and the tripod
are neatly parallel and tight.
4、The picture on the left is the frame after Step1 is assembled.
Back Beam
Left Beam
Right Beam
1 2 3 4
M5*18
M5*30
M5*18
M5*8
Notice label on bags !
Step 2 Assemble X beam set and front beam
1
1
2 Front Beam
3
3
4
4
5
5
Motherboard
tripod
Tripod
Assembly steps：
1、Push the X beam assembly into the U-shaped frame, paying
attention to the direction of white logo !
2、Required components: tripod*1, motherboard tripod, front frame
beam, Step3 screw pack, T-shaped hexagonal wrench.
3、Assemble the tripod, main board tripod, and front frame beam
according to the right figure, install them in the order of step 12345,
and tighten the screws 1/3/4/5 in the order.
1 3 4 5
M5*18
M5*30
M5*8
M5*18
Step 3 Install the belt
Installation steps:
Install the belt to the position shown in the figure,note:
1. The belt should be installed in the direction of the arrow in the figure
above.
2. The tooth pattern of the belt faces downwards and engages with the
gears.
3. Please pass the belt through the flat hole, there should be an extra part
of the belt at one end for easy pulling and tightening of the belt.
We suggest you don't cut off the extra belt after Step 4 , this is good for
the future maintenance.
Pass the belt through
the flat hole
Step 4 Install T nut
1
1
2
2
1
2
Do not tighten the T nut, pull
the belt with your hand to
make the belt tight
With the belt tightened, tighten
the screws to keep the long side
of the T-nut perpendicular to the
groove.
Put the T nut into the groove, the long
side is parallel to the groove, Strongly
press the T nut while rotating the wrench
clockwise to make the long side of the T
nut perpendicular to the groove
Put the T nut into the groove, the long side is
parallel to the groove, Strongly press the T nut
while rotating the wrench clockwise to make the
long side of the T nut perpendicular to the groove
Tighten the screws and keep
the long side of the T-nut
perpendicular to the groove.
Installation steps:
1. First install the T-nut on one side as shown
in the figure.
2. Install the other end of the T-nut on the
other side, and note that the long side of the
T-nut is perpendicular to the groove after
installation. After the installation is complete,
the belt is in a tight state. For extra belts, if
you are not familiar with the use of belts, we
suggest that you do not cut off the extra belts
Do not screw
through the nut
Step 5 Install laser module and Laser shield
1 . M4 hand screw
2. M3 hand screw
1
1
2
2
Install laser module and
Laser shield by hand screws
Step 6 Install air pipes and cables
Install the blue air tube on the machine, fix it on
the X beam with screws and brackets, the air tube
is finally inserted on the nozzle, after installation
you need to slide the laser to confirm that the air
tube is in a loose state.
1. Connect the motor and cable, note: the X and Y motor
are marked on the terminals. Install the laser cable.
2. Fix the cable on the machine hole with black cable tie.
Keep cables slack.
3. Fix the air tube and cable with sticky strips to ensure that
they are tied together. Slide the lasers to confirm that they
are in a relaxed state.
1
1
2
3
Important Using Tips
50mm
Focusing principle:
1、The focal length of the SCULPFUN laser
module is fixed and cannot be changed .
2、The specific position of the laser focus is
50mm directly below the edge of the aluminum
alloy shell of the laser module.
3、We provide a 50mm measuring aluminum
column to help find the laser focus.
4、When the laser is focused on the surface
of the engraved object, it will exert its maximum
engraving effect.
50mm
50mm
measuring
aluminum
column
the surface of the engraved object
edge of the
aluminum
alloy shell
How to adjust the tension
of X and Y belts
1. For the X-axis, just loosen the screw,
tighten it to one side, and then fix the
screw.
2. For the Y-axis, you need to adjust the
hexagonal eccentric nut next to the bottom
roller, which can control the tightness of
the Y-axis. In addition, the tightness of the
Y-axis belt also affects the Y-axis. You can
lift the machine at an angle of 45°. If the
beam slides smoothly, it means that the Y-
axis is proper.
X-axis controller
Pull
Adjust with
wrench
Eccentric nut
Customer Service:
Ø For detailed warranty policy,please visit
our official website at: www.sculpfun3d.com
Ø For Laser Engraver technical support and
service,please email:
support@sculpfun3d.com
Manufacturer: Shenzhen Sculpfun
Technology Co., Ltd.
Address: Room 201, Building B, Jinzhicai Factory, No. 1,
Guihua Industrial Zone, Guanlan Street, Longhua District,
Shenzhen City, Guangdong China
Note：This Manual is just for installation, For how to
use laserGRBL software, how to show the position of
the engraving pattern, and how to set the engraving
parameters of different materials, please scan the QR
code or visit the website www.sculpfun3d.com to
download the User Manual.
Scanner APP:
QR Code Reader
/Barcode Scanner
or any APP with scanner
Sculp your fun !
Engraving software:
LightBurn for better cutting:
https://lightburnsoftware.com/
LaserGRBL is easier for beginner: http://lasergrbl.com/
Learn more in User manual or YouTube.
Ø Official Group for Sculpfun Users:
https://www.facebook.com/groups/538557
960530958
ØOFFICIAL YOUTUBE:
https://www.youtube.com/c/SCULPFUNReal
/videos
Indice
Lingue:
Altri manuali SCULPFUN Incisore
