CommScope BUDI-S Manuale utente
BUDI-S
INSTALLATION INSTRUCTION
Building distributor
• Box
• Base tray
• Base tower
• Termination units
• Inserts for SMOUV and ANT
Accessories
Introduction
Suitable for FTTH applications where easily pre-connectorized splitters
modules can be build in. The box is designed In such a way that it is
suitable for both spliced and connectorized solutions of the riser cable.
Kit content
• Tray kit
Seals
Wrap around cable seals
Sealblock 4 x 10 mm
Cable diameter (mm) Foam (± 5 mm)
3 95
4 90
5 80
6 75
7 70
8 60
9 50
10 40
Sealblock 4 x 15 mm
Cable diameter (mm) Foam (± 5 mm)
9 125
10 115
11 105
12 95
13 85
14 70
15 60
Sealblock 2 x 20 mm
Cable diameter (mm) Foam (± 5 mm)
14 155
15 140
16 125
17 110
18 95
19 85
20 75
Sealblock 24 x 8 mm
Cable range 1.8 – 7 mm
Sealblock rubber 1 x 18
To use in ports S4-S5 only
Cable range 3 – 8 mm
Standard seals
PG 16
PG 21
PG 29
PG 29 (PTS 24)
TC-906-S-IP
Rev A, Mar 2017
www.commscope.com
2
1.3 Different wrap-around ports are available (including brackets).
Use two guiding pins to open the ports and to secure the bottom part to
the box.
1.4 Install the cable bracket depending the cable seal.
1.1 Make a cut on both sides of the port to open the port.
1 Preparation of the box
1.2 Use a plier to break-out the port, starting from front to back.
Remove all the burrs.
S1 S2 S3
3
2.1 Mark the loose tube at the position of the tray.
2.2 1: Storage area (dark fibers)
2: Splicing to splitter modules
3: Point to point applications
1.5 Use a hacksaw to reach the onion rings, which can be opened
with a plier to open the in-line ports (S4/S5).
1.6 Install the wrap-around rubber seal into the port.
2 Base tray
1
2
3
2.3 Route the fibers to the different areas (1-2-3).
1
2
3
S4 S5
4
2.4 Store the fibers which will be used later.
2.5 Store the fibers which will be spliced day 1 to the splitter
modules.
2
2.6 Store the fibers which will be spliced day 1 for the point-to-
point applications.
3
3 Drop cables (point-to-point applications)
3.1 Remove the outer jacket over a distance of 1.2 m.
3.2 Wrap one layer of foam (20 mm) on the securing position if
needed. Terminate the aramid strength member by securing the cable/
pigtail onto thebracket with tie-wrap. Depending the amount of aramid
strength member, it needs to be wrapped twice around the bracket.
3.3 Install the terminated drop cable in the numbered ports on the
base tray.
5
3.4 Splice the fibers from the drop cable to the fibers from the
looped cable. In case of SMOUV, use the insert.
3.5 Install the cover onto the tray.
Slide
Click
4.1 Install the patch tray onto the tower.
4.2 Insert the adaptor into the designated positions.
4 Patching tray
6
4.3 Install the cable into the port and secure with hook and loop
fastener tape onto the bracket and seal with foam (see length page 1).
Mini –PICO (no connectors)
4.4 Close the port.
4.5 Install the foam at the position on the patch tray and secure
with 2 tie-wraps as shown on the picture.
4.6 Install the splice holders onto the patch tray.
4.7 Splice the MINI PICO fibers to the pigtails and store the
overlength in the splice area. Check the orientation of both fibers to
avoid crossings.
Foam
Hook and loop
fastener
Hook and loop
fastener
7
4.8 Install the cover onto the tray.
Mini PICO (pre-connectorized)
4.10 Connect the mini PICO cable with the designated adaptors
and store the overlength in the splice area.
4.9 In case of pre-connectorized MINI PICO cable, fibers are also
routed behind the tower and secured with foam and tie-wraps onto the
tray.
4.11 Install the cover onto the tray.
Click
Slide
Click
4.13 2 parking places for pigtails from splitter which are not used
day 1 can be installed.
4.12 Secure the patch trays with the rubber flex part, as shown.
8
5.3 Install the splitter into the holder.
5.5 Install the incoming pigtail and route the fiber to the splicing to
“splicing to splitter modules” for splicing. Remove the outer jacket over a
distance of 1.2 m. Secure with foam and tie-wrap.
5.4 Route the pigtails to the designated adapters on the patch tray.
Bundle the pigtails with hook and loop fastener when needed.
5.2 Install the bend control and splitter holder into the box.
5 Splitters
OCM6 in-line
5.1 Install the adapter in the splitter holder.
9
OCM6 butt
5.7 Route the incoming pigtails of the splitter (marked with red
flag) to the base tray and remove the outer jacket from the mark over a
distance of 1.2 m. Secure with foam and tie-wrap onto the base tray.
5.6 Install the splitter into the holder and route the pigtails via the
bend control.
5.8 Install the splice holders onto the patch tray.
5.9 Splice the MINI PICO fibers to the pigtails and store the
overlength in the splice area. Check the orientation of both fibers to
avoid crossings.
Slide Click
10
6 Closing the box
6.1 Close the box.
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali CommScope Cavi e connettori
CommScope
CommScope HELIAX FiberFeed FDH1210-24SE2 Series Foglio di istruzioni
CommScope
CommScope LC Manuale utente
CommScope
CommScope FIST-RSKG-16 Manuale utente
CommScope
CommScope ION-M7P Manuale utente
CommScope
CommScope LSX-288 Manuale utente
CommScope
CommScope HELIAX FiberFeed FDH1206-12M50 Series Foglio di istruzioni
CommScope
CommScope NOVUX SXT Manuale utente
CommScope
CommScope AMP NETCONNECT 1933352 Series Manuale utente
CommScope
CommScope FOSC450 C Manuale utente
CommScope
CommScope FOSC-OC-3 Manuale utente
CommScope
CommScope SYSTIMAX 360 iPatch... Manuale utente
CommScope
CommScope QWIK MPO Series Manuale utente
CommScope
CommScope FIBER INDEXING TERMINAL Manuale utente
CommScope
CommScope HELIAX MFJS6UDHNA00 Manuale utente
CommScope
CommScope ETHERSEAL 1479563-2 Manuale utente
CommScope
CommScope LC Manuale utente
CommScope
CommScope LightCrimp Plus ST Manuale utente
CommScope
CommScope AMP NETCONNECT SL Series Manuale utente
CommScope
CommScope 760230938 Manuale utente
CommScope
CommScope NOVUX SEC 100 Manuale utente
