CommScope Constellation CPT-PP-48C Manuale utente

TC-96343-IP

Rev A, October 2022

commscope.com

User

Manual

Constellation™ Power Transition Panel (CPT-PP-48C)

Electronic Only Document (EOD)

Constellation Power Transition Panel

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.1 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2 Important Safety Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.3 Constellation Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.4 Constellation Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.5 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Specifications and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 UNPACKING AND INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 MOUNTING THE PANEL ON THE RACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5 CONNECTING THE POWER TRANSMITTER TO THE TRANSITION POINT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6 INSTALLING THE POWER LEG OF THE HFPC CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Content Page

27924-A

TC-96343-IP

Page 2

1 INTRODUCTION

Constellation™ delivers power and data over extended distances using a hybrid fiber power cable.

The power is delivered from the power transmitter to the receiver using a combination of 20 AWG

and 16 AWG cabling. The junction between the 20 AWG and 16 AWG power conductors is

facilitated by the Power Transition Panel (CPT-PP-48C) documented in this user manual.

Contents of this manual include a description of the product and procedures for unpacking the

panel, mounting it on a 19-inch rack, and terminating the 20 AWG and 16 AWG cables onto the

panel.

1.1 Trademarks

CommScope (logo), CommScope, and Constellation are trademarks of CommScope, Inc.

Digital Electricity is a trademark of VoltServer, Inc.

1.2 Important Safety Cautions

When installing or operating the panel, observe these safety cautions:

• To reduce the risk of fire, electric shock, and injury to persons, read, understand, and adhere

to the following instructions as well as any warnings marked on the product.

• This product has a remote risk of electric shock. Never install the product in wet conditions or

during lightning storms. Never touch uninsulated power wires or terminals.

• This product is intended for indoor use only.

• Wearing safety glasses during installation of this panel is recommended.

• All wiring that connects to this equipment must meet applicable local and national building

codes and network wiring standards.

• Care should be taken not to compromise the stability of the rack by installation of this

equipment.

TC-96343-IP

Page 3

1.3 Constellation Products

Table 1 lists currently available Constellation products with catalog numbers and Material IDs

(MIDs).

Table 1. Constellation Products

PRODUCT CATALOG # MID

Power Transmitter CPCX-12 760254285

Management Module CTX-MGT 760254286

Power Supply CPM-3K 760254287

Transmitter Card CTX-6 760254288

Multi-Chassis Synch Card CMX-6 760254289

SAF D to L620P Cord CABLE-PWR SAFD-L620P 760254290

C19 to L620P Cord CABLE-PWR C19-L620P 760254291

C19 to 5-15P Cord CABLE-PWR C19-515P 760254292

Power Transition Panel CPT-PP-48C 760254293

Power Patch Cable CTX-CBL-10 760254294

Powered Backplane CPCB-1 760252855

Enclosure CPCE-1 760252854

TBD HFPC TBD

Power Supply Bay Cover PM500-COVER 760254642

TC-96343-IP

Page 4

1.4 Constellation Publications

Table 2 lists technical publications available for the Constellation system. These manuals can be

accessed online using the QR code on the physical product or by contacting the CommScope

Support Center at https://www.commscope.com/SupportCenter

1.5 Contact Information

• To find out more about CommScope®products, visit us on the web at

www.commscope.com

•For technical assistance, customer service, or to report any missing/damaged parts, visit

us at http://www.commscope.com/SupportCenter

Table 2. Constellation Technical Publications

Publication Title Publication #

Constellation Power Transition Panel (CPT-PP-48C) User Manual TC-96343-IP

Constellation Transmitter Card (CTX-6) Data Sheet TC-96344-IP

Constellation Power Supply (3PM-3K) Data Sheet TC-96345-IP

Constellation Multi-Chassis Synch Card (CMX-6) Quick Start Guide TC-96346-IP

Constellation Power Supply Bay Cover (PM500-COVER) Data Sheet TC-96347-IP

Constellation Management Software for Transmitters User Manual TC-96348-IP

Constellation Powered Backplane (CPCB-1) Quick Start Guide TC-96349-IP

Constellation Enclosure (CPCE-1) Quick Start Guide TC-96350-IP

Constellation Best Practices Guide TC-96351-IP

Constellation Power Transmitter (CPX-12) Quick Start Guide TC-96352-IP

TC-96343-IP

Page 5

2 PRODUCT DESCRIPTION

2.1 General Description

The Power Transition Panel (CPT-PP-48C) is a 19-inch rack-mountable panel that provides a

controlled transition point between the 20 AWG power interconnection leads connecting the panel

to the Power Transmitter (CPX-12) and the 16 AWG power conductors present in the Hybrid Fiber

Power Cable (HFPC). The HFPC connects the panel to the Powered Backplane (CPCB-1) as

shown in Figure 1.

The Power Interconnection Leads (CTX-CBL-10) can be purchased in packs of 6 separate from the

transmitter. The HFPC cable is also ordered separately. All connections to the CPT-PP-48C are

made on site when the equipment is installed.

Figure 1. Position of Power Transition Panel in Constellation System

The CPT-PP-48C is a collection of 48 color coded terminal blocks. Each terminal block provides for

cross-connection of one conductor from the transmitter and one conductor from the backplane.

Prior to installation, the conductors must be separated out from the two cables and stripped back to

the specified distance per Section 5 on Page 10 and Section 6 on Page 12. The bare wires from the

transmitter can then be plugged directly into the assigned bottom slots in the terminal blocks. It is

recommended that the 16 AWG copper conductors in the HFPC that ultimately terminate at

powered backplane are fitted with wire ferrules prior to being inserted in the top slots of the terminal

blocks.

Note: The fiber leg of the HFPC (also shown in Figure 1) is not covered in this manual.

ENCLOSURE

(CPCE-1)

27925-A

POWERED

BACKPLANE

(CPCB-1)

POWER

TRANSITION

PANEL

(CPT-PP-48C)

POWER

TRANSMITTER

(CPCX-12)

POWER

TRANSMITTER

CARD

(CTX-6)

POWER

INTERCONNECT

LEAD

(CTX-CBL-10)

HYBRID FIBER POWER CABLE (HFPC)

POWER

LEG OF

HFPC

FIBER

LEG OF

HFPC

TO FIBER

PANEL

TC-96343-IP

Page 6

2.2 Main Features

Figure 2 shows a front view of the Power Transition Panel. The main features are:

•Sheet Metal Bezel—provides a support structure so that the terminal blocks can be installed

in a 19-inch rack.

•Mounting Holes—4 mounting holes are provided so that the panel can be attached to the

rack.

•Terminal Block—a pass-through block that connects one conductor from the transmitter and

one conductor from the backplane. There are 48 terminal blocks.

Figure 2. Power Transition Panel Main Features

•Top Slot for Backplane—the slot where a single conductor from the power leg of the HFPC

attaches to a single terminal block on the panel.

•Bottom Slot for Transmitter—the slot where a single conductor from the power transmitter

interconnect lead attaches to a single terminal block on the panel.

MOUNTING

HOLE (4x)

27926-A

BEZEL TERMINAL

BLOCK (48x)

TOP

SLOT

BOTTOM

SLOT

TC-96343-IP

Page 7

2.3 Specifications and Dimensions

Figure 3 shows dimensions for the Power Transition Panel. Table 3 lists dimensions.

Figure 3. Power Transition Panel Dimensions

Table 3. Power Transition Panel Specifications

Parameter Va lue

Height 3.47 in (8.83 cm)

Width 19.0 in. (48.26 cm)

Depth 1.75 in. (4.43 cm)

Weight 1.93 lbs. (0.875 Kg)

15.07 IN.

(40.01 CM)

19.00 IN.

(48.26 CM)

3.47 IN.

(8.81 CM)

2.20 IN.

(5.59 CM)

27927-A

TOP VIEW

FRONT VIEW

SIDE VIEW

1.23 IN.

(3.31 CM)

1.75 IN.

(4.43 CM)

TC-96343-IP

Page 8

3 UNPACKING AND INSPECTION

Use the following procedure to unpack and inspect the product. Verify parts against Table 4 below.

1. Inspect the exterior of the shipping carton for evidence of rough handling that may have

damaged the components in the container.

2. Open the carton and remove the panel while carefully checking the contents for damage.

3. If damage is found or parts are missing, contact the CommScope Support Center using the

URL: http://www.commscope.com/SupportCenter

4. If damaged, save the carton for inspection by the carrier.

Table 4. Power Transition Panel Parts List

Description Quantity

Power Transition Panel 1

Panel fastener pack 1

TC-96343-IP

Page 9

4 MOUNTING THE PANEL ON THE RACK

The panel mounts on a 19-inch equipment rack. Use the following procedure.

1. Align the four mounting holes with the four holes in the selected rack location.

2. Secure the panel to the rack using the four screws provided.

Refer to Figure 4.

Figure 4. Mounting the Power Transition Panel

27928-A

TC-96343-IP

Page 10

5 CONNECTING THE POWER TRANSMITTER TO THE TRANSITION POINT

PANEL

The CTX-CBL-10 is a 20 AWG power interconnect lead that is used to connect the output of the

transmitter to the Power Transition Panel (CPT-PP-48C). One end of the two-conductor cable is

terminated onto the outer positions of a four position plug that is keyed to match the input to the

CTX-6 power transmitter card (a subassembly of the CPCX-12). The jacket on the panel end of the

cable has been removed and the conductors stripped back between 10 and 12 mm.These exposed

connectors are the ends that terminate into the bottom slot of the CPT-PP-48C.

A small segment of loose heat shrink is also present on the 10-foot cable. If the cable is intended to

be used in its original 10-foot length, the heat shrink can be applied at the end of the cable and the

interconnect is ready for termination onto the panel. If the interconnect is to be shortened before

terminating onto the panel, use the following procedure.

1. Cut the cable to the desired length (taking into account enough length for the desired cable

routing).

2. Remove approximately 4 inches of the outer jacket.

3. Remove 10-12 mm of insulation from the ends of the insulated conductors.

4. Route the cable from the transition panel along the rack to the transmitter.

5. Use a small screwdriver or equivalent to press on the clamp release on the terminal block

(Figure 5).

Figure 5. Releasing the Clamp

27930-A

Indice

Altri manuali CommScope Hardware di rete

CommScope

CommScope TC-96370-IP Manuale utente

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuale utente

CommScope

CommScope LSX Manuale utente

CommScope

CommScope SYSTIMAX 100BASE-T Manuale utente

CommScope

CommScope CPP-UDDM-SL-1U-24 Manuale utente

CommScope

CommScope SYSTIMAX EHD Manuale utente

CommScope

CommScope FDC-W8-FAT Manuale utente

CommScope

CommScope CPPR-QF-F-1U-E Manuale utente

CommScope

CommScope M3200 Manuale utente

CommScope

CommScope FPX Series Manuale utente

CommScope

CommScope ION-U EU H 23/23 Manuale utente

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuale utente

CommScope

CommScope OneCell RP5000 Series Guida

CommScope

CommScope SYSTIMAX AirSPEED AP542 Manuale utente

CommScope

CommScope FPX Series Manuale utente

CommScope

CommScope EHD Manuale utente

CommScope

CommScope WCS-2 Manuale utente

CommScope

CommScope ONECELL RP5200 Manuale

CommScope

CommScope RUCKUS SmartZone 100 Manuale utente

CommScope

CommScope AMP NETCONNECT MRJ21 Manuale utente

CommScope

CommScope SCIL-B Manuale utente

CommScope

CommScope MRJ21 Quick Fit Cassette Manuale utente

CommScope

CommScope ST-BSP60 Manuale utente

CommScope

CommScope NOVUX DSC 650 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente