CommScope SD-4U-SPLICE PANEL Manuale utente

LEFT REAR ENTRY RIGHT REAR ENTRY

PARTS LIST

Break Out Input and Output Cables as follows.

Break out the cables per the diagram below, fitting the sub-units with mesh tubing as indicated. Route each sub-unit “bundle” into either back corner of the panel

as shown in Step 3. Secure the mesh tubing with tie wraps and felt tape in the location shown.

Install Panel as follows: (a) mount panel on frame; (b) remove

ALL transportation screws and tape from panel; (c) mount input and

output cables on frame at adjacent location using cable clamp of

customer choice (order separately); see Step 2 breakout diagram.

CABLE MESH TUBING BARE FIBER

CABLE CLAMP (SEE STEP 1)

SD-4U-SPLICE PANEL

CABLE

CLAMP

TRANSPORTATION

SCREW

MESH

LEFT

REAR

ENTRY

EXAMPLE

Product Description

The SD-4U-Splice Panel is a 19-inch

rack-mount panel for terminating

and splicing Outside Plant (OSP)

cables or Infra Facility Cables (IFC).

Each panel accomodates 1728

fibers in 6 C-size splice trays.

Each splice tray holds

4 splice modules, providing

288 mass fusion splices

(12 fiber ribbon x 24 splices).

Accessories listed at right must

be ordered separately .

DESCRIPTION

SD-4U SPLICE PANEL

RACK SCREW

PARTS LIST

QUANTITY

BREAKOUT

TIE POINT ON PANEL

PHILLIPS #2 SCREWDRIVER

SNIPS

TIE WRAPS

CABLE CLAMP 1

PARTS LIST

DESCRIPTION

TOOLS REQUIRED

QUANTITY

PARTS LIST

DESCRIPTION

ACCESSORIES

QUANTITY

FOST-ACC-C-TRAY -RIBN-24

SPLICE TRAY

MESH TUBING 200 FT.

Sections shown

are diagrammatic,

not proportional.

NOTE:

TIE

WRAP

FELT

TAPE

Install Cable as follows: (a) remove back cover (unscrew knob to

release it); (b) route cable bundles to the rear of the panel;

secure on cable mount using cable tie and felt tape; (c) bring bundles

forward to the panel front; (d) unpack splice tray and identify

components; (e) route bundles to splice tray for splicing on

nearby table; (f) splice as shown; see Note below.

BACK

COVER

PANEL

SIDE

WALLS

NOT

SHOWN

UNSCREW

KNOBS

TO RELEASE

26323-A

FELT

TAPE

TIE

WRAPS

SPLICE

MODULES

SPLICE

TRAY

WITH

COVER

NOTE: These steps give a pictorial

overview. For complete

instructions, refer

to CommScope

document provided

with splice tray.

3cFELT

TAPE

& TIE

WRAP

FELT

TAPE

& TIE

WRAP

OVERHEAD VIEW

(ONE BUNDLE)

LEFT REAR

ENTRY

EXAMPLE

TIE

WRAP

FELT

TAPE

Quick

Start

CommScope (logo) and CommScope are trademarks.

TC-96255-IP · Rev A · December 2018

BREAKOUT LENGTH

126 IN. (320.04 CM)

100 IN.

(254.0 CM)

26 IN.

(66.0 CM)

POSITIONAL

(ADDITIONAL MESH

LENGTH TO BREAKOUT)

Continue adding cables and splice trays as needed.

Install them within the splice panel as shown from bottom to top.

The panel holds 6 splice trays.

RED LATCH

SPLICE

TRAY

SPLICE

TRAY TOWER

RED

LATCH

Wind splice tray and attached bundles back into the panel,

looping the bundles within the panel as shown.

Position the splice tray as shown at a right angle to the bottom hinge on

the splice tray deck. Insert the leading edge of the splice tray into the

tower and then rotate the tray 90 degrees to place it flat onto the

bottom of the panel.

Install first loaded splice tray into panel.

NOTE: Press on the red latch to pull out the work tray on the

front of the panel as shown.

26805-A

NOTE: For clarity, splice trays are shown without fiber in these views.

Release red latch (see above) and

slide shelf with splice trays back

into panel. Dress cables in an

orderly manner. Close panel doors.

LEFT REAR ENTRY ROUTING

RIGHT REAR ENTRY ROUTING

TC-96255-IP · Rev A · December 2018 PRODUCT PATENTS: https://www.commscope.com/ProductPatent/ProductPatent.aspx PRODUCT INFORMATION AND TECHNICAL SUPPORT: http://www.commscope.com/SupportCenter

Altri manuali CommScope Hardware di rete

CommScope

CommScope LSX Manuale utente

CommScope

CommScope SYSTIMAX 360 iPatch G2 MPO Manuale utente

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manuale utente

CommScope

CommScope ION-U EU H 23/23 Manuale utente

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manuale utente

CommScope

CommScope CPP-UDDM-SL-1U-24 Manuale utente

CommScope

CommScope WCS-2 Manuale utente

CommScope

CommScope NETCONNECT 1479542-1 Manuale utente

CommScope

CommScope AMP NETCONNECT MRJ21 Manuale utente

CommScope

CommScope EHD Manuale utente

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuale utente

CommScope

CommScope RUCKUS SmartZone 100 Manuale utente

CommScope

CommScope ONECELL RP5200 Manuale

CommScope

CommScope FPX Series Manuale utente

CommScope

CommScope NOVUX DSC 650 Manuale utente

CommScope

CommScope RUCKUS SmartZone 300 Manuale utente

CommScope

CommScope ION-M7P Manuale utente

CommScope

CommScope TC-96370-IP Manuale utente

CommScope

CommScope Mini-OTE 300 Manuale utente

CommScope

CommScope ION-M23 SDARS Manuale utente

CommScope

CommScope FDC-W8-FAT Manuale utente

CommScope

CommScope NOVUX SEC 100 Manuale utente

CommScope

CommScope SCIL-B Manuale utente

CommScope

CommScope FOSC-OC-6 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente