Compex NetPassage WP18 1A Manuale utente

Questo manuale è adatto per i seguenti modelli

11

Indice

Altri manuali Compex Punto di accesso wireless

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Quick Install Guide

Wireless 54Mbps A+G Dualband Access Point

With Integrated PoE

NetPassage WP18 1A, 2A, 2B, 2C, 3A, 3B, 3C, 3D

NetPassage WP18 6A, 6B, 6C, 6D (RoHS-compliant)

i

Table of Contents

1: Introduction......................................................................................1

Packaging Content.................................................................................. 2

2: Hardware Setup..............................................................................3

Option 1: Using Power Adapter to Supply Power................................ 3

Option 2: Using PoE to Supply Power..................................................... 5

3: Access to Web Interface...............................................................8

Access to the Web Interface Through Utility - uConfig ...................... 9

Access to the Web Interface Manually.............................................. 12

4: Panel Views and Descriptions.....................................................13

Panel Description....................................................................................15

5: Technical Specifications..............................................................17

WARRANTY REGISTRATION CARD.......................................................21

1

1: Introduction

The Wireless 54Mbps A+G Dualband Access Point doesn’t just operate in wired

network environments, it also upholds simultaneous IEEE802.11a and

IEEE802.11b/g connections, as is often required in hotspots and other public

Internet access deployment.

The access point is designed to support state-of-the-art security standards such

as the Wi-Fi Protected Access (WPA) protocol, the 802.1x authentication

standard, and 64/128-bits Wired Equivalent Privacy (WEP) encryption.

This high-performance access point also bears the exclusive uConfig utility and

support broadband Internet sharing is an additional function that can be

enabled.

When the user chooses to enable routing, additional enhanced functions to the

wireless access point operation are available, such as Load Balancing; Fail-

Over Redundancy; Parallel Broadband; built-in DHCP server; Virtual Servers

based on IP and Port Forwarding; De-Militarised Zone hosts; Packet Filtering;

and much more!

2

Packaging Content

Actual product appearance may differ slightly depending on the hardware

version.

1 X Access Point

2 x External Antenna

1 x Power Adapter

1 x Read-Me-First Note

1 x Product CD

2 x Rest Foot

3

!

Important: To ensure proper functionality of the

access point, these two antennas MUST

NOT be swapped.

2: Hardware Setup

The access point can be powered using either the power adapter, or the PoE*

or IEEE 802.3af PoE.

The installation process for the three options is described below.

Option 1: Using Power Adapter to Supply Power

Before attaching a pair of external

antennas to the access point, take

note of the ‘A’ marking on one of

the two antennas.

The antenna with the ‘A’ marking is

the Dualband AG Antenna.

The antenna without the marking is

the single-band G Antenna.

• PoE is available in several models and power outputs.

Please contact your supplier for the correct model and power requirements.

Connect the Dualband

AG antenna to Ant-1 on

the LEFT.

Connect the single-band

G antenna to Ant-2 on

the RIGHT.

‘A’ marking

4

Insert one end of the RJ45 Ethernet cable to any of the LAN ports (1, 2, 3, or 4)

on the access point and the other end to your PC’s Ethernet network adapter.

Attach the power adapter to the main electrical supply and connect the

power plug into the socket of the access point.

Power on your PC.

Notice that the Power and the corresponding port LEDs have lighted up.

This indicates that connection has been established successfully between the

access point and your PC.

PC

5

Option 2: Using PoE to Supply Power

PoE (Power-Over-Ethernet) can be used to power the access point. This

accessory supplies operational power to the wireless access point through the

Ethernet cable connection and is available separately.

If you wish to use PoE to supply power to the access point, follow the steps

below:

Follow the steps described in Option One.

Connect one end of an RJ45 Ethernet cable to LAN OUT port of the PoE

Injector and the other end to Port 4 of the access point.

For PoE, the recommended length of the RJ45 Category 5 cable is up to 50

metres.

6

Connect the RJ45 Ethernet cable attached to the PoE Injector to your PC’s

Ethernet network adapter.

Once you have finished configuring the access point, you can connect the

PoE Injector’s RJ45 Ethernet cable to your network device, such as a switch or

a hub.

Connect the power adapter supplied in the PoE kit to the main electrical

supply and the power plug into the socket of the injector.

Note:

DO NOT interchange the access point and PoE power adapters.

The voltage and current supply is incompatible.

7

Turn on your power supply. Notice that the Power LEDs have lighted up. This

indicates that the access point is receiving power through the PoE Injector.

Notice also that the Port 4LEDs have lighted up. This indicates that

connection between the access point and your PC has been established.

8

3: Access to Web Interface

There are 2 methods to access the web interface of the access point:

1. Access to the Web Interface Through Utility – uConfig

Access the web interface directly without having to change the IP address

of your PC.

2. Access to the Web Interface Through web browser

1. Assign an IP address to your PC so that it is in the same subnet

as the access point.

(Example: 192.168.168.xxx where x can be any value from 2 to

254)

2. Enter IP address of the access point in the address bar of

Internet Explorer and press Enter.