CompuLab FIT-PC4 Manuale utente

FIT-PC4

Owner’s Manual

FIT-PC4 Owner’s Manual

April -2014

Introduction

Package contents

Hardware specifications

FIT-PC4 features

Quick start guide

Connecting FIT-PC4

Booting Linux

Booting Windows 7

Maintenance

Opening service door

Service bay

BIOS Setup Utility

Warranty and RMA

Warranty

RMA

Tips for saving power

General

In Operating System

For more information and to obtain the latest revision of this document, please visit

www.fit-pc.com

Introduction

Package contents

1. FIT-PC4 computer

2. Power supply: input 100-240VAC 50/60Hz, 36W output 12VDC 3A, DC plug lock,

3. Attachable Standard North-American and EU plugs AC cord. *

4. HDMI to DVI adapter

5. Audio 3.5mm to RCA cable

6. 2 WiFi antennas (in some models)

7. Mini-serial to DB9-female adapter cable

To use FIT-PC4, you will need:

A display with DVI/HDMI input + DVI/HDMI cable

USB keyboard and mouse

* Local resellers may supply FIT-PC4 with other AC cord types.

Hardware specifications

Processor

Pro Model

Value Model

Type

AMD GX-420CA System-on-Chip

AMD A4-1250 System-on-Chip

Cores

64-bit quad core

64-bit dual core

Clock speed

2GHz

1GHz

TDP

25W

Chipset

SoC (CPU and Chipset on the same die)

Memory

Supported

2x SO-DIMM 204-pin DDR3/DDR3L/DDR3U SDRAM memory slots

Up to 16GB (2x 8GB) DDR3/DDR3L/DDR3U-1600 (1.5V/1.35V/1.25V)

Storage

Supported

1x SATA up to 6 Gbps (SATA 3.0) for internal 2.5” HDD/SSD

1x mSATA slot up to 6 Gbps (SATA 3.0)

Graphics

GPU

AMD Radeon HD 8400E

Dual display mode supported

AMD Radeon HD 8210

Dual display mode supported

Display Interface 1

HDMI 1.4a up to 1920 x 1200 @ 60Hz

Display Interface 2

HDMI 1.4a up to 1920 x 1200 @ 60Hz

Audio

Codec

Realtek ALC888-VC2 HD audio codec

Audio Output

Analog stereo output

Digital 7.1+2 channels S/PDIF output

3.5mm jack

Audio Input

Analog stereo Microphone input

Digital S/PDIF input

3.5mm jack

Networking

Pro Model

Value Model

LAN

2x GbE LAN ports

LAN1: Intel I211 GbE controller (RJ-45)

LAN2: Intel I211 GbE controller (RJ-45)

Wireless

Intel 2.4/5GHz dual band 7260HMW

WLAN 802.11ac

Bluetooth 4.0

AzureWave AW-NB057H

WLAN 802.11b/g/n

Bluetooth 3.0

Connectivity

USB

2x USB 3.0

6x USB 2.0

Serial

1x Serial communication port

COM1: RS232 via mini serial connector

Micro-SD slot support SD/SDHC/SDXC cards

Transfer rates up to 25 MB/s (50MHz clock)

Special I/O

1x micro SIM slot (6 pins)4

Expansion

Half/Full-size mini-PCIe socket

Half/Full-size mini-PCIe/mSATA socket2

Advanced Technologies

CPU Virtualization

Yes

Special Functionality

Auto-On

Wake-on-LAN

Wake-on-Timer

PXE Boot

Watchdog

CEC support on Display Interface 1

Operating System

Supported

Windows 7/8, 32-bit and 64-bit

Linux 32-bit and 64-bit

Embedded OS

Operating Conditions

Input Voltage

Unregulated 10 –15VDC input1

Power Consumption

8W –25W

5W –11W

Operating Temperature

1. Commercial

HDD models: 0°C –50°C

SSD models: 0°C –70°C

2. Extended (TE)

SSD models only: -20°C –70°C

3. Industrial (TI)

SSD models only: -40°C –70°C

Enclosure

Material

Die Cast Aluminum

Cooling

Passive Cooling Fanless Design

Dimensions

19cm x 16cm x 4cm

19cm x 16cm x 2.5cm

Weight

1100gr

1067gr

Package

Warranty

5 years3

Notes

1. Nominal input voltage: 12V

2. Shared with mSATA

3. For products purchased since 1-Jan-2013

4. For use with mini PCIe Cellular Modem module

FIT-PC4 features

Front panel

The features of the front panel of FIT-PC4 depend on specific FACE Module used and are documented

separately.

Power

FIT-PC4 has a tactile power push-button. It is used for turning on/off the PC and for standby/resume when

supported by the operating system.

A push of at least 5 seconds will always turn off the FIT-PC4.

Display

FIT-PC4 has dual display interface with support for dual head.

1. 2x HDMI with audio support (CEC support on one HDMI port)

To connect FIT-PC4 to a DVI display, use the provided HDMI to DVI-D adapter. Use a DVI cable to connect

the adapter to the display.

Audio

There are 2 standard 3.5mm jacks on the back panel.

Right:

Stereo line-in using a standard 3.5mm plug

S/PDIF 7.1 in using provided cable

Left:

Stereo line-out using a standard 3.5mm plug

S/PDIF 7.1 out using provided cable

LAN

FIT-PC4 features two 10/100/1000BaseT Ethernet ports using standard RJ45 connectors. Use a standard

Ethernet cables to connect.

The connectors feature built-in LEDs that are lit when a connection is detected.

WLAN

2 WLAN antennas are supplied in models with integrated WiFi and should be screwed into the standard

SMA connectors.

USB

There are 2 USB 3.0 ports (5 Gbps) and 2 USB 2.0 ports on the back panel. FM4U module contains 4

additional USB2.0 ports on the front panel. All USB ports support current up to 1A.

Serial port

RS232 mini-serial ports is located on the back panel.

Mini-serial to DB9 cable to connect to standard serial devices is supplied in the package.

Quick start guide

Connecting FIT-PC4

Turn off the display and connect it to the FIT-PC4 HDMI connector (use the HDMI to DVI adapter

if needed).

Connect the USB keyboard and mouse to USB 2 connectors.

Plug the Ethernet cable into the Ethernet connector.

In FIT-PC4 models with WiFi: Mount the WiFi Antennas on the SMA connector by turning it

clockwise repeatedly until the antenna holds firm.

Insert the DC plug into the FIT-PC4 DC-in jack. Rotate clockwise 900to secure.

Plug the speakers into the line-out jack.

Connect the power supply to the AC cord and plug the cord into AC outlet. The front panel logo

should light up as the FIT-PC4 boots.

Booting Linux

Linux loads automatically on power up. Upon boot you will be guided through the Linux Mint first-boot

setup procedure.

Booting Windows 7

Upon first power-up, you will be guided through the Windows Welcome procedure which is self-

explanatory. The Windows 7 serial number is printed on the Windows 7 label on the bottom of your FIT-

PC4.

Maintenance

FIT-PC4 requires no maintenance. You should not take the FIT-PC4 apart other than opening the service

door. Taking FIT-PC4 apart will void its warranty.

The following operations can be conducted by the user:

Opening service door

1. Unscrew marked Philips screw at the bottom to release service-door.

2. Slide out service-door until it stops –about 10 mm.

3. Service-door is now detached. Lift edge of service-door to completely remove.

Re-assemble in reverse order. Hard disk connects by sliding-in the service-door.

Service bay

The service-bay provides easy access to hard-disk, RAM, and mini-PCIe sockets incl. WLAN module.

Hard disk is 2.5” 7mm/9.5mm SATA. It is screwed to service door by 4 screws, 2 on each side. It is

recommended to use 5400 RPM hard disk or SSD. 7200 RPM or higher is not recommended due to higher

power consumption and risk of overheating.

RAM –use up to DDR3/DDR3L -1600 SO-DIMM modules (1.5V/1.35V), or up to DDR3U-1333 SO-DIMM

modules (1.25V).

Mini-PCIe –the half-size mini-PCIe is normally used for WLAN. If you remove the WLAN module make sure

to isolate the ends of antenna cables with some tape to avoid short-circuit. The full-size mini PCIe is

available for any use.

BIOS Setup Utility

Entering BIOS Setup Utility

Turn off the FIT-PC4.

Turn on while holding down the F2 key.

See http://www.fit-pc.com/wiki/index.php/Main_Page.

Warranty and RMA

Warranty

CompuLab guarantees products against defects in workmanship and material for a period of 60

months from the date of shipment.

Your sole remedy and CompuLab’s sole liability shall be for CompuLab, at its sole discretion, to

either repair or replace the defective product at no charge.

This warranty is void if the product has been altered or damaged by accident, misuse or abuse.

RMA

Keep the original package for shipping in case of hardware failure.

In case of HW failure of an FIT-PC4 under warranty, please contact the seller of that FIT-PC4.

Please provide the following required information:

FIT-PC4 serial number

Name of purchaser

Address

Problem description

If the FIT-PC4 was purchased directly from CompuLab, please email rma@fit-pc.com.

Tips for saving power

General

Working without a connected display automatically disables the graphics controller –saving

power.

Disconnect external USB devices when not in use.

In Operating System

Use power scheme as follows

Turn of monitor after several minutes not in use

Turn off hard disk after several minutes not in use

System standby after an hour not in use

FIT-PC4

Manufacturer: CompuLab Ltd.

This device complies with Part 15 of the

FCC Rules.

Operation is subject to the following two

conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any

interference received, including

interference that may cause undesired

operation.

Statement

Changes or modifications to this

equipment not expressly approved by the

party responsible for compliance

(CompuLab Ltd.) could void the user’s

authority to operate the equipment.

Statement

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and

receiver.

-Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician

for help.

Altri manuali per FIT-PC4

Indice

Altri manuali CompuLab Scrivania

CompuLab

CompuLab fitlet2 FC-USB Manuale utente

CompuLab

CompuLab Airtop Manuale utente

CompuLab

CompuLab UTILITE2 Manuale utente

CompuLab

CompuLab Airtop-C0 Manuale utente

CompuLab

CompuLab fitlet2 FC-USB Manuale utente

CompuLab

CompuLab Airtop2 Manuale utente

CompuLab

CompuLab fitlet3 Manuale utente

CompuLab

CompuLab Fitlet2 FC-POED Manuale utente

CompuLab

CompuLab IPC2 Manuale utente

CompuLab

CompuLab fit-PC2 Manuale utente

CompuLab

CompuLab fitlet2 FC-USB Manuale utente

CompuLab

CompuLab Fitlet FC-OPLN Manuale utente

CompuLab

CompuLab SBC-FITPC3 Manuale utente

CompuLab

CompuLab Tensor-I22 Manuale utente

CompuLab

CompuLab Airtop3 Manuale utente

CompuLab

CompuLab fit-PC2i Manuale utente

CompuLab

CompuLab Trim-Slice Manuale utente

CompuLab

CompuLab fitlet Manuale utente

CompuLab

CompuLab IPC3 Manuale utente

CompuLab

CompuLab Fitlet-H Manuale utente

Manuali Scrivania popolari di altre marche

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP Presario SV7000 - Desktop PC Manuale utente

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente