Contec COM-2(PC)F Manuale utente
COM-2(PC)F
RS-232C (2ch) Serial I/O Board
User’s Guide
COM-2(PC)F i
Copyright
Copyright 1996 CONTEC Co., LTD. ALL RIGHTS RESERVED
No part of this document may be copied or reproduced in any form
by any means without prior written consent of CONTEC Co., LTD.
CONTEC Co., LTD. makes no commitment to update or keep
current the information contained in this document. The
information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this
document. Should you notice an omission or any questionable
item in this document, please feel free to notify CONTEC Co.,
LTD.
Regardless of the foregoing statement, CONTEC assumes no
responsibility for any errors that may appear in this document nor
for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft, MS-DOS, Windows and Windows NT are
trademarks of Microsoft Corporation. Other brand and product
names are trademarks of their respective holder.
COM-2(PC)Fii
Product Configuration
-COM-2(PC)FBoard…1
-Sample Program Diskette (3.5inch/1.44MB)…1
-User's Guide (This Booklet)…1
Unpacking:
This board is specially packed in an anti-static bag to prevent
damage in shipping.
Check the contents to make sure that you have everything listed
above. If you do not have all the items, contact your distributor
or CONTEC group office where you purchased.
Note! Do not remove the board from its protective packaging until the
computer case is open and ready for installation. Electrical static
can cause damage to electrical components.
COM-2(PC)F iii
Table of Contents
Copyright............................................................................i
Trademarks ........................................................................i
Product Configuration ..................................................... ii
1. Introduction .............................................................1
About the COM-2(PC)F Board.....................................1
Support Software of Option..........................................1
Features.........................................................................1
Limited Three-Year Warranty......................................2
How to Obtain Service..................................................2
Liability.........................................................................2
About the Manual.........................................................3
2. How to Use the Board ...............................................5
Compatible Mode and Enhanced Mode ...........................5
Compatible Mode..........................................................5
Enhanced Mode.............................................................5
Operating under Windows Me/98.....................................6
Procedure.......................................................................6
Operating under Windows 95.........................................10
Procedure.....................................................................10
Operating under Windows 2000.....................................14
Procedure.....................................................................14
Operating under Windows NT .......................................18
Procedure.....................................................................18
Operating under Windows 3.1........................................19
Procedure.....................................................................19
Operating under MS-DOS..............................................20
Procedure.....................................................................20
3. Hardware Setup ..................................................... 23
Names of Board Components.........................................23
I/O Address Setting.........................................................24
Setting Procedure .......................................................25
Interrupt Level Setting...................................................26
Setting Procedure .......................................................26
COM-2(PC)Fiv
Mounting Method............................................................28
Connecting the External Devices...................................31
Connecting the Cable......................................................32
4. System Reference.................................................... 33
Specifications...................................................................33
Circuitry Diagrams.........................................................34
Block Diagram.................................................................34
5. Troubleshooting...................................................... 35
QUESTIONS:..................................................................35
Is the pilot light on?....................................................35
Did the system boot up? .............................................35
Does your program work?...........................................35
Does the sample program work?................................36
Is the input data accurate?.........................................36
Still have a probrem?..................................................36
6. Appendix................................................................ 39
A. Sample Programs (for MS-DOS)................................39
COM-2(PC)F Diskette ................................................39
Sample Programs........................................................40
Switch and Jumper Settings......................................42
Cable Connection........................................................44
B. Notes on Developing Driver Software.......................56
Internal Registers.......................................................56
Baud Rate Selection....................................................57
LSI Recovery Time......................................................58
Various Aspects of Interrupt Handling in Enhanced
Mode and Compatible Mode.......................................60
C. The Details on NS16550 ............................................62
D. Difference Between the COM-2(PC)F
and COM-2(PC)V.......................................................64
7. Index ..................................................................... 65
COM-2(PC)F v
List of Figures
Figure 3.1. Names of Board Components and Default Factory
Settings..................................................................... 23
Figure 3.2. I/O Address DIP Switch............................................ 25
Figure 3.3. Interrupt Level Settings............................................. 26
Figure 3.4. Rear Panel of IBM-PC/AT......................................... 28
Figure 3.5. Removing the Cover.................................................. 28
Figure 3.6. Expansion Slot Cover................................................ 29
Figure 3.7. Anchoring the COM-2(PC)F..................................... 30
Figure 3.8. Interface Connectors (CN1 and CN2)........................ 31
Figure 3.9. CN1 and CN2 Pin Assignments................................ 31
Figure 3.10.Example Connection to a Modem ............................. 32
Figure 3.11.Example Connection to a PC..................................... 32
Figure 3.12.Example Connection to a Device............................... 32
Figure 4.1. Circuitry Diagrams.................................................... 34
Figure 4.2. COM-2(PC)F Block Diagram.................................... 34
Figure 6.1. Floppy Disk Files...................................................... 40
Figure 6.2. 9-pin Connector Diagram.......................................... 44
Figure 6.3. Flowchart of Sample Program 1................................ 45
Figure 6.4. Flowchart of Sample Program 2................................ 46
Figure 6.5. Flowchart of Sample Program 3................................ 47
Figure 6.6. Flowchart of Sample Program 4................................ 48
Figure 6.7. Flowchart of Sample Program 5................................ 49
Figure 6.8. Flowchart of Sample Program 6................................ 50
Figure 6.9. Flowchart of Sample Program 7................................ 51
Figure 6.10.Flowchart of Sample Program 8................................ 52
COM-2(PC)Fvi
Figure 6.11.Flowchart of Sample Program 9................................ 53
Figure 6.12.Flowchart of Sample Program10............................... 54
Figure 6.13.Flowchart of Sample Program 11 .............................. 55
Figure 6.14. IVR Bit Function in Enhanced Mode........................ 61
Figure 6.15.Difference in Jumpers (JP1~JP3)............................... 64
COM-2(PC)F vii
List of Tables
Table 2.1. COM Port Support for Various Programming
Languages................................................................. 21
Table 3.1. I/O Address Settings................................................. 25
Table 3.2. Example Compatible Mode Settings......................... 27
Table 4.1. Specifications............................................................ 33
Table 6.1. Data Format.............................................................. 40
Table 6.2. Switch and Jumper Settings of Sample Program 1, 2,
and 5......................................................................... 42
Table 6.3. Switch and Jumper Settings of Sample Program 3, 4, 6,
and 10....................................................................... 42
Table 6.4. Switch and Jumper Settings of Sample Program 7.... 43
Table 6.5. Switch and Jumper Settings of Sample Program 11... 43
Table 6.6. Function Selection through Internal Registers........... 56
Table 6.7. Baud Rate and Divisors............................................. 57
Table 6.8. Number of Times the IN Instruction Must be Executed
for the 2EFh Port after Accessing the LSI................. 58
Table 6.9. NS16550's Register (Short from National
Semiconductor's data book) < 1 / 2 >.................... 62
Table 6.9. NS16550's Register (Short from National
Semiconductor's data book) < 2 / 2 >.................... 63
Table 6.10. Specifications Differences....................................... 64
COM-2(PC)Fviii
Introduction
COM-2(PC)F 1
1. Introduction
About the COM-2(PC)F Board
The COM-2(PC)F is an IBM PC/AT ISA-Bus add-on interface
board for multi-channel RS-232C asynchronous communications.
It features two serial communication ports and a programmable
communication rate ranging from 50 to 115,200 bps for
communication or modem control.
Support Software of Option
-For Windows API-PAC(W32)
-For Windows 3.1 API-SIO(PC)WIN
-For MS-DOS SUPPORT-PAC(PC)103
Features
-2-channel asynchronous communication
-Supports RS-232C protocol
-Programmable communication rate from 50 to 115,200 bits per
second
-Two operational modes : Enhanced and Compatible
(COM1, COM2, COM3, and COM4)
For more information, see System Reference.
Indice
Altri manuali Contec Sistema I/O
Contec
Contec DAI16-4(USB) Manuale utente
Contec
Contec DIO-48DX-USB Manuale utente
Contec
Contec POW150X Manuale utente
Contec
Contec DI-128L-PE Manuale utente
Contec
Contec DIO-3232L-PE Manuale utente
Contec
Contec DIO-1616TB-PE Manuale utente
Contec
Contec DIO-1616L-PE Manuale utente
Contec
Contec PIO-32H(PCI)H Manuale utente
Contec
Contec COM-2PD(PCI)H Manuale utente
Contec
Contec PIO-16/16L(CB)H Manuale utente
Contec
Contec PIO-16H Manuale utente
Contec
Contec AO-1604CI3-PCI Manuale utente
Contec
Contec AI-1664LAX-USB Manuale utente
Contec
Contec PCI-bus Analog Input Multi-Function Board... Manuale utente
Contec
Contec PIO-64L(PCI)H Manuale utente
Contec
Contec PIO-32 Series Manuale utente
Contec
Contec AD12-64(PCI) Manuale utente
Contec
Contec AO-1604CI2-PCI Manuale utente
Contec
Contec N Series Manuale utente
Contec
Contec DIO-1616RY-PE Manuale utente
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
