Crystal Vision Smart DA Manuale utente

Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England.

E-mail: [email protected] Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059

Smart DA

Monitoring Distribution Amplifier

Smart DA User Manual R1.1 Crystal Vision

Smart DA User Manual R1.1 117/01/07

Contents

1 Introduction 3

2 Hardware installation 4

2.1 Rear modules and signal I/O 4

Rear module connections with RM01 4

Rear module connections with RM18 5

Rear module connections with RM02 6

2.2 General Purpose Interface (GPI) 7

3 Card edge operation 11

3.1 Card-edge switch settings 11

3.2 Reading card edge LEDs 12

4 Using the active front panel 13

4.1 Module selected 13

Updating the display 15

The Smart DA active panel menu structure 16

Selecting audio group 17

Configuring alarm delay 18

Status 19

5Statesman 20

5.1 Statesman operation 20

Selecting a monitoring audio group 21

EDH status 21

Signal status 21

Set up 22

Configuring delay 22

Smart DA User Manual R1.1 Crystal Vision

Smart DA User Manual R1.1 217/01/07

6 Trouble shooting 23

6.1 Card edge status LEDs 23

Basic fault finding guide 24

7 Specification 25

Revision 1 Statesman GUIs and descriptions updated. 17-01-07

Crystal Vision Introduction

Smart DA User Manual R1.1 317/01/07

1 Introduction

Smart DA is an SDI distribution amplifier with on board signal monitoring facilities.

Combined with an active front panel or Statesman PC control system, both video and

embedded audio status can be viewed. Depending on the rear module used, Smart DA

will give either five or eight SDI outputs.

Smart DA intelligent Distribution Amplifier

Smart DA monitors the following parameters:

•Input present

•Input standard

•Video black

•Video frozen

•Audio group present

•Audio silence

•EDH monitoring, missing, full field error and active picture error.

•GPI output of selected alarms

Smart DA is a 100mm x 266mm module, which fits in Crystal Vision’s four standard

frames and can be integrated with any boards from the company’s full product range. It

can be used with three different frame rear modules, with the RM01 giving five SDI

outputs and the RM02 and RM18 both giving eight.

Applications include immediate indication of signal or transmission problems in large

systems especially in unmanned automatic playout facilities or as a simple signal probe.

Crystal Vision Hardware installation

Smart DA User Manual R1.1 417/01/07

2Hardware installation

The Smart DA single height module can be used with the RM01, RM02 and RM18 rear

connectors, which will fit into all Crystal Vision rack frames. All modules can be

connected or removed while the frame is powered, without damaging the board.

2.1 Rear modules and signal I/O

The Indigo 4 4U frame will house up to 24 single height modules with up to three power

supplies. The Indigo 2 and FR2AV 2U frames will house up to 12 single height modules

and dual power supplies. The Indigo 1 and FR1AV 1U frames will house six single height

modules and a single power supply. The Indigo DT DTBAV and DTBAV desk top boxes

both have a built-in power supply and will house up to two single height modules.

Note: For details of fitting rear connectors please refer to the appropriate frame manual

Rear module connections with RM01

RM01 fits in all frames Description

RM01

•24 Smart DA modules per

Indigo 4 frame

•12 per Indigo 2 or FR2AV

frame

•Six per Indigo 1 or FR1AV

frame

•Two per Indigo DT

•All frame slots can be used

BNC I/O assignment

SDI OUT(1) Reclocked SDI output

SDI IN SDI input

SDI OUT(2) Reclocked SDI output

SDI OUT(3) Reclocked SDI output

SDI OUT(4) Reclocked SDI output

SDI OUT(5) Reclocked SDI output

Crystal Vision Hardware installation

Smart DA User Manual R1.1 517/01/07

Rear module connections with RM18

RM18 fits in all frames Description

RM18

•12 Smart DA modules per Indigo

4 frame

•Six per Indigo 2 or FR2AV

frame

•Six per Indigo 1 or FR1AV

frame

•Two per Indigo DT

•Card fits in upper slot

•No card fits in lower slot

BNC I/O assignment

AN/C

BSDI input

CRe-clocked SDI output

DRe-clocked SDI output

ERe-clocked SDI output

FRe-clocked SDI output

GN/C

HRe-clocked SDI output

IRe-clocked SDI output

JRe-clocked SDI output

KN/C

LRe-clocked SDI output

Crystal Vision Hardware installation

Smart DA User Manual R1.1 617/01/07

Rear module connections with RM02

RM02 fits in a 2U Indigo or FR2AV frame Description

RM02

•12 Smart DA modules per

Indigo 4 frame

•Nine modules per 2U frame

•Three modules per rear

connector

•Nine connections available

•Card 1 fits in slots 1, 5 and 9

•Card 2 fits in slots 2, 6 and 10

•Card 3 fits in slots 4, 8 and 12

•No card fits in 3, 7 or 11

BNC I/O assignment

SDI IN SDI input

1Reclocked SDI output

2Reclocked SDI output

3Reclocked SDI output

4Reclocked SDI output

5Reclocked SDI output

6Reclocked SDI output

7Reclocked SDI output

8/IN2 Reclocked SDI output

Crystal Vision Hardware installation

Smart DA User Manual R1.1 717/01/07

2.2 General Purpose Interface (GPI)

Each frame slot has up to six connections ‘a-f ‘for GPI control and monitoring. These

connections are available at the rear of the frame on the 26-way D type Remote

connectors.

GPI Default Statesman configured Low (<1V) High (+5V)

1‘a’ Input Missing

2‘b’ Input frozen or

black See table. Alarm condition Non- alarm

3‘c’ No function

4‘d’ No function

5‘e’ No function

6‘f’ No function

As supplied, each GPI output has a 220Ωresistor in series with its output. This allows for

an external LED to be driven, connected to a DC voltage of +5V.

GPI 1 and GPI 2 can be configured to show an alarm condition for any individual or

group of error conditions. Configuration of the GPI reporting can only be carried out

using either an active control panel or Statesman.

Reportable error conditions

Silence from any channel 1-4 of selected group for

longer than set interval

Video input not present

Video input standard changed

Video picture black for longer than set interval

Video picture frozen for longer than set interval

EDH error

EDH missing

Note. When set to local control, GP1 input present/missing will react immediately to a loss of input

signal. GP2 will report an error only if any of the monitored parameters are incorrect for approximately

30 seconds. Error delay is not variable in local mode.

Crystal Vision Hardware installation

Smart DA User Manual R1.1 817/01/07

4U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of eight rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

18 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

27 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

38 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)

47 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)

55 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

64 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

75 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)

84 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)

93 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)

12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

18 (5) 9 (5) 18 (5) 26 (5) 19 (6) 20 (6)

27 (5) 16 (5) 17 (5) 25 (5) 10 (6) 11 (6)

38 (7) 9 (7) 18 (7) 26 (7) 19 (8) 20 (8)

47 (7) 16 (7) 17 (7) 25 (7) 10 (8) 11 (8)

55 (5) 6 (5) 15 (5) 24 (5) 1 (6) 2 (6)

64 (5) 14 (5) 13 (5) 23 (5) 3 (6) 4 (6)

75 (7) 6 (7) 15 (7) 24 (7) 1 (8) 2 (8)

84 (7) 14 (7) 13 (7) 23 (7) 3 (8) 4 (8)

93 (5) 12 (5) 22 (5) 21 (5) 12 (6) 13 (6)

10 10 (5) 11 (5) 19 (5) 20 (5) 21 (6) 22 (6)

11 3 (7) 12 (7) 22 (7) 21 (7) 12 (8) 13 (8)

12 10 (7) 11 (7) 19 (7) 20 (7) 21 (8) 22 (8)

Table shows pin number (Remote number)

Note: Remote 1, Remote 3, Remote 5 and Remote 7 are 26 way high-density D-Type female

sockets. Frame ground is pin 2 and +5V @500mA is pin 1 in each case.

Remote 2, Remote 4, Remote 6 and Remote 8 are 26 way high-density D-Type male plugs

and frame ground is pin 6 in each case and +5V @500mA is pin 15 on Remote 2 and Remote

Note. The +5V output is protected by self-resetting thermal fuses, which limit the total output

current available from Remotes 1-4 to approximately 1A. Remotes 5-8 are similarly

protected.

UpperLower

Crystal Vision Hardware installation

Smart DA User Manual R1.1 917/01/07

2U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of four rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

18 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

27 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

38 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)

47 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)

55 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

64 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

75 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)

84 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)

93 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)

12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)

Table shows pin number (remote number)

Note: Remote 1 and Remote 3 are 26 way high-density D-Type female sockets. Frame ground is

pin 2 and +5V @500mA is pin 1 in each case.

Remote 2 and Remote 4 are 26 way high-density D-Type male plugs and frame ground is pin

6 in each case and +5V @500mA is pin 15 on Remote 2.

Note. The +5V output is protected by self-resetting thermal fuses, which limit the total output

current available from Remotes 1-4 to approximately 1A.

1U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of two rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

18 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

27 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

35 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

44 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

53 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

610 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

Table shows pin number (remote number)

Note: Remote 1: 26 way high-density D-Type female socket. Frame ground is pin 2 and +5V

@500mA is pin 1.

Remote 2: 26 way high-density D-Type male plugs and frame ground is pin 6 and +5V

@500mA is pin 15

Note. The +5V output is protected by self-resetting thermal fuses, which limit the total output

current available from Remotes 1-2 to approximately 1A.

Indice

Altri manuali Crystal Vision Amplificatore

Crystal Vision

Crystal Vision VDA110R Manuale utente

Crystal Vision

Crystal Vision Indigo AADA416FM Manuale utente

Crystal Vision

Crystal Vision 3GDA-VF Manuale utente

Crystal Vision

Crystal Vision Indigo DADA208 Manuale utente

Crystal Vision

Crystal Vision Indigo VDA210M HD Manuale utente

Crystal Vision

Crystal Vision ViPA102 Manuale utente

Crystal Vision

Crystal Vision VDA110M Manuale utente

Crystal Vision

Crystal Vision Indigo AADA-STM-1 Manuale utente

Crystal Vision

Crystal Vision DDA108A-BP Manuale utente

Crystal Vision

Crystal Vision DDA208B Manuale utente

Crystal Vision

Crystal Vision Indigo 3GDA105 Manuale utente

Crystal Vision

Crystal Vision Indigo 3GDA105R Manuale utente

Crystal Vision

Crystal Vision VDA110M Manuale utente

Crystal Vision

Crystal Vision VDA210R Manuale utente

Crystal Vision

Crystal Vision AADA416FR Manuale utente

Crystal Vision

Crystal Vision AADA-VF Manuale utente

Crystal Vision

Crystal Vision DDA108A Manuale utente

Crystal Vision

Crystal Vision ViPA204 Manuale utente

Crystal Vision

Crystal Vision Indigo VDA210M HD Manuale utente

Crystal Vision

Crystal Vision VDA110R Manuale utente

Crystal Vision

Crystal Vision DADA-VF Manuale utente

Crystal Vision

Crystal Vision 3GDA204R Manuale utente

Crystal Vision

Crystal Vision HDDA104R Manuale utente

Crystal Vision

Crystal Vision Indigo MADDA 105 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente