CTC Union JB230 Series Manuale utente

JB230 Series Switch BoxJB230 Series Switch Box

4-12 Channel4-12 Channel

Product ManualProduct Manual

• Introduction...................................................................3

• Product Description...........................................................3

• Product Dimensions...........................................................4

• Mounting Instructions .........................................................5

• Conduit Entry .................................................................6

• Grounding ....................................................................7

• Sensor Installation ............................................................9

• Post Installation Testing ..................................................... 12

• Maintenance ................................................................ 13

• Warranty & Refund .......................................................... 14

T  C

I

CTC switch box solutions allow for the monitoring of remotely mounted vibration

sensors, which would otherwise be restricted to human access due to safety

considerations.

JB230 Series Switch Box Overview: 4-12 channel boxes, stainless steel

enclosure

The JB230 Switch Box is a common cable termination point for bringing

compatible cables for triaxial sensors into a switch box for routine data collection

with portable data collectors. JB series enclosures are designed to have field

input cabling installed behind the board. A flip-down panel allows the user to wire

connections on location. The JB series also features an IEPE bias indicator light

built into the box itself, which can be used to indicate errors in the field wiring or

the sensor.

Rated for NEMA 4X (IP66), the JB230 is resistant to hose directed fluid

and corrosion. The box can also withstand harsh environments, including

temperatures ranging from -58 to 180 °F (-50 to 82 °C). A key latch is installed on

the door, allowing the box to be sealed from the elements when not in use.

If a continuous output application is desired that can be easily accomplished by

purchasing the optional CTC accessory “T” plug part number JB933-1A.

P D

Measurement

Location Card

Data Collector

Access (BNC)

Switch

Quick

Connect

Option

Screw

Terminal

Option

Data Collector

Access (4 pin)

Input Terminal Strip Options

Bias

Indicator

Light

Figure 1. Dimensions

Figure 2. Diagram

Front View Side View

M I

Molded mounting brackets are included on the enclosure. Wall anchoring screws

are not included.

CTC

Vibration

Switch Box

(Rear View)

Mounting

Brackets

0.31 in./7.95 mm

Figure 3. Mounting Bracket Placement

C E

If you have purchased a switch box without cable entries provided, you should

add your own entry prior to mounting the enclosure. CTC does not recommend

putting holes in the top of enclosures as it will cause restricted access to the

wire termination connection points and also allow possible moisture ingress.

Note: To prevent a buildup of condensation inside the enclosure, provide drainage

by drilling a hole in the lowest point of the conduit.

Correct

Figure 4. Conduit Entry for Switch Box

Incorrect

Drill Drain

Hole Here

G

Ensure the shield ground wire on the JB230 Series Switch Box is grounded to

earth ground.

A. Mounting to Earth Ground

When mounting JB230 Series Switch boxes to earth ground (such as an I-Beam),

no additional steps are necessary, as the enclosure is grounded internally.

Figure 5. Switch Box (JB230) Earth Ground

G

B. Mounting to non-grounded structure

When mounting the switch box to a non-grounded structure, ensure the shield

ground wire or customer supplied ground wire is tied to a source of earth ground.

Figure 6. Ground Wire Placement

S I

Installation of sensors/signal input cable

1. Feed blunt cut end through the cable entry at the bottom of the enclosure.

Note: it is recommended that cables are marked on both ends.

For cord grip cable entry, take off the cord grip cover with bushing and run cable

through it then into the enclosure, hand tighten cord grip cover to base to prevent

damage of cord grip.

1. Strip outer jacket of cable back 1¼ in. and remove all of the shielding.

2. Separate the internal wires from the shield.

3. Strip red and black insulation back ¼ in.

Figure 8. Bottom View with

Cord Grips Installed

Figure 7. Front View

Figure 9. Stripped Wire

(-)

Shield / Drain wire

(+) Channel Y

(+) Channel X

(+) Channel Z

Figure 10. Field Wiring for 4-Conductor Triaxial Sensor Inputs

GND

SENSOR #1 SENSOR #2

GND

SENSOR #3

GND

SENSOR #4

GND

SENSOR #5

GND

SENSOR #6

GND

SENSOR #7

GND

SENSOR #8

GND

SENSOR #9 SENSOR #10

GND

SENSOR #11

GND

SENSOR #12

GND

Sensor Inputs

Green = Positive X Axis

Red = Positive Y Axis

White = Positive Z Axis

Black = Common

Grey = Shield (Ground)

Inputs

S I

4. Locate the appropriate plug (identified by channel number), remove it, and

install the wires using a small flathead screwdriver. Push plug back into location.

Orientation is as follows:

a. Green insulated conductor wire is connected to Channel X.

b. Red insulated conductor wire is connected to Channel Y.

c. White insulated conductor wire is connected to Channel Z.

d. Black insulated conductor wire is connected to (-).

e. Shield drain wire is connected to ground (GND).

GND

SENSOR #1 SENSOR #2

GND

SENSOR #3

GND

SENSOR #4

GND

SENSOR #5

GND

SENSOR #6

GND

SENSOR #7

GND

SENSOR #8

GND

SENSOR #9 SENSOR #10

GND

SENSOR #11

GND

SENSOR #12

GND

Sensor Inputs

Green = Positive X Axis

Red = Positive Y Axis

White = Positive Z Axis

Black = Common

Grey = Shield (Ground)

Inputs

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali CTC Union Interruttore

CTC Union

CTC Union IGS-2408SM-24PH Manuale utente

CTC Union

CTC Union SB202 Series Manuale utente

CTC Union

CTC Union SB142 Manuale utente

CTC Union

CTC Union IGS-401F Manuale utente

CTC Union

CTC Union IGS?401F?4PH24 Manuale utente

CTC Union

CTC Union TSB1000 Series Manuale utente

CTC Union

CTC Union IGS-812SM Series Manuale utente

CTC Union

CTC Union SB282 Series Manuale utente

CTC Union

CTC Union IGS-803SM-8PH24 Manuale utente

CTC Union

CTC Union FS-802GS-8PH Manuale utente

CTC Union

CTC Union JB330 Series Manuale utente

CTC Union

CTC Union JB220 Series Manuale utente

CTC Union

CTC Union FRM220A-GSW/SNMP Manuale utente

CTC Union

CTC Union IGS+803SM-8PH Manuale utente

CTC Union

CTC Union FSW3224 Manuale utente

CTC Union

CTC Union ITP-800-8PH24 Manuale utente

CTC Union

CTC Union IFS?402F Manuale utente

CTC Union

CTC Union GSW-1005MS Manuale utente

CTC Union

CTC Union ITP-G800SM-8PH24 Manuale utente

CTC Union

CTC Union IFS-803GSM-8PH24 Manuale utente

CTC Union

CTC Union IFS+402GSM-4PHE24 Manuale utente

CTC Union

CTC Union JB210 Series Manuale utente

CTC Union

CTC Union GSW-3208M Manuale utente

CTC Union

CTC Union SB262 Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente