Cub CB-425e Manuale utente
THERMAL TRANSFER / DIRECT THERMAL
BAR CODE PRINTER
Cub CB-425e
USER’S
MANUAL
Contents
1. Introduction ...........................................ii
1.1 Product Introduction ...............................................................................ii
1.2 Compliances ............................................................................................ii
2. Operations Overview .....................................1
2.1 Unpacking and Inspection ......................................................................1
2.2 Printer Overview ......................................................................................2
2.2.1 Front View ......................................................................................2
2.2.2 Interior view....................................................................................4
2.2.3 Rear View........................................................................................5
3. Setup .................................................6
3.1 Setting Up the Printer..............................................................................6
3.2 Open / Close the Top Cover....................................................................7
3.3 Loading the Ribbon.................................................................................8
3.4 Loading the Media .................................................................................11
3.4.1 Loading the media....................................................................... 11
3.4.2 External Label Roll Mount Installation (Option)........................13
3.4.3 Loading Media in Peel-off Mode (Option)..................................15
3.4.4 Loading Media in Cutter Mode (Option).....................................17
3.5 Diagnostic Tool......................................................................................18
3.5.1 Start the Diagnostic Tool.............................................................18
3.5.2 Printer Function (Calibrate sensor, Ethernet setup, RTC
setup………)..........................................................................................19
3.6 Install SD Memory Card.........................................................................20
4. LED and Button Functions ................................22
4.1 LED indicator .........................................................................................22
4.2 Regular button function........................................................................22
4.3 Power on utilities...................................................................................22
4.3.1 Ribbon and Gap/Black Mark Sensor Calibration ......................23
4.3.2 Gap/Black Mark Calibration, Self-test and Dump Mode ...........24
4.3.3 Printer Initialization......................................................................26
4.3.4 Set Black Mark Sensor as Media Sensor and Calibrate the Black
Mark Sensor..........................................................................................27
4.3.5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor
27
4.3.6 Skip AUTO.BAS............................................................................27
i
ii
5. Troubleshooting ........................................28
5.1 LED Status..............................................................................................28
5.2 Print Quality ...........................................................................................29
6. Maintenance ...........................................30
i
1. Introduction
1.1 Product Introduction
Thank you for purchasing the Cub CB-425e bar code printer.Although the printer takes only a
a small amount of space, it delivers reliable, superior performance.
This printer provides both thermal transfer and direct thermal printing at user selectable speeds
of: 2.0, 3.0, 4.0 or 5.0 ips.It acceptsroll feed and fan-fold labels for both thermal transfer
and direct thermal printing. The unit will print all common 1D & 2D bar code formats.
Fonts and bar codes can be printed in 4 directions, 8 different alphanumeric bitmap fonts
fonts are preloaded into the printers memory. The unit also supports type fonts.
1.2 Compliances
CE Class B:
EN55022: 1998+A1: 2000+A2: 2003
EN55024: 1998+A1: 2001+A2: 2003 IEC 61000-4 Series
EN61000-3-2: 2006 & EN61000-3-3: 1995+A1: 2001
FCC Part 15, Class B
UL, CUL
C-Tick:
CFR 47, Part 15/CISPR 22 3rd Edition: 1997, Class B
ANSI C63.4: 2003
Canadian ICES-003
TÜV-GS: EN60950: 2000
Wichtige Sicherheits-Hinweise
1.Bitte lesen Sie Diese Hinweis sorgfältig durch
2.Heben Sie diese Anleitung fűr den späteren Gebrauch auf.
3.Vor jedem Reinigen ist das Gerät vom Stromentz zu trennen. Verwenden Sie Keine
Flűssig-oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur
Reinigung.
4.Die Netzanschlußsteckdose soll nahe dem Gerät angebraucht und leicht zugänglich
sein.
5.Das Gerät ist vor Feuchtigkeit zu schűtzen.
6.Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Beschädigungen hervorrufen.
7.Beáchten Sie beim Anschluß an das stromnetz die Anschlußwerte.
8. Dieses das Gerät kann bis zu einer Außentemperatur von maximal 40℃betieben
werden.
ii
iii
WARNING
HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
WARNUNG!
GEFÄHRLICHE BEWEGLICHE TEILE – FINGER UND ANDERE KÖRPERTEILE
FERNHALTEN!
VORSICHT!
EXPLOSIONSGEFAHR BEI ERSATZ DER
BATTERIE DURCH UNZULÄSSIGEN TYP.
VERBRAUCHTE BATTERIEN IMMER
VORSCHRIFTSGEMÄSS ENTSORGEN!
Note：
* Continuous printing may cause the printersmotor to overheat. The printer will stop printing automatically
for about 10~15 minutes until motor has cooled down. Please do not turn poweroff when printer pauses
or the data transfered to the printer buffer will be lost.
* The maximum printing ratio per dot line is 15% for this printer. To print the full web black line, the
maximum black line height is limited to 40 dots, which is 5mm for 203 DPI resolution printer and 3.3mm
for 300 DPI resolution printer.
2. Operations Overview
2.1 Unpacking and Inspection
This printer has been specially packaged to withstand damage during shipping.
Please carefully inspect the packaging and printer upon receiving the unit.
Please retain the packaging materials in case you need to reship the printer.
The following items are included with the printer.
One Cub CB-425e printer
One Software & Documentation CD
One quick installation guide
One power cord
One auto switching power supply
One USB interface cable
If any parts are missing, please contact the Customer Service Department of your
purchased reseller or distributor.
2.2 Printer Overview
2.2.1 Front View
3
2
1. Ribbon access cover
2. Top cover open lever
3. Media view window
4. LED indicator
5. Feed button
6. SD card socket
* Recommended SD card specification.
SD card spec SD card capacity Approved SD card manufacturer
V1.0, V1.1 128 MB SanDisk, Transcend
V1.0, V1.1 256 MB SanDisk, Transcend, Panasonic
V1.0, V1.1 512 MB SanDisk, Transcend, Panasonic
V1.0, V1.1 1 GB SanDisk, Transcend, Panasonic
V2.0 SDHC CLASS 4 4 GB
V2.0 SDHC CLASS 6 4 GB SanDisk, Transcend, Panasonic
V1.0, V1.1 microSD 128 MB Transcend, Panasonic
V1.0, V1.1 microSD 256 MB Transcend, Panasonic
5
6
2
1
4
3
V1.0, V1.1 microSD 512 MB Panasonic
V1.0, V1.1 microSD 1 GB Transcend, Panasonic
V2.0 SDHC CLASS 4 microSD 4 GB Panasonic
V2.0 SDHC CLASS 6 microSD 4 GB Transcend
V1.0, V1.1 miniSD 128 MB Transcend, Panasonic
V1.0, V1.1 miniSD 256 MB Transcend, Panasonic
V1.0, V1.1 miniSD 512 MB Transcend, Panasonic
V1.0, V1.1 miniSD 1 GB Transcend, Panasonic
V2.0 SDHC CLASS 4 miniSD 4 GB Transcend
V2.0 SDHC CLASS 6 miniSD 4 GB
- The DOS FAT file system is supported for the SD card.
- Folders/files stored in the SD card should be in the 8.3 filename format
- The miniSD/microSD card to SD card slot adapter is required.
2.2.2 Interior view
7
1
8
2
4
5
3
4
9
10
11
12
6
1. Ribbon rewind hub
2. Ribbon rewind gear
3. Gap sensor (receiver)
4. Media holder
5. Media holder lock switch
6. Gap sensor (transmitter)
7. Printhead
8. Ribbon supply hub
9. Top cover support
10. Media guide adjustment knob
11. Black mark sensor
12. Platen roller
Indice
Altri manuali Cub Lettore di codici a barre
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
