Custom Dynamics Dynamic Strips CD-DS-ST-B Manuale utente

Custom Dynamics® Dynamic Strips™ Turn Signals

Installation Instructions

Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

09-2017

We thank you for purchasing the Custom Dynamics® Dynamic

Strips™ Turn Signals. Our products utilize the latest technology

and high quality components to ensure you the most reliable ser-

vice. We offer one of the best warranty programs in the industry

and we back our products with excellent customer support, if you

have questions before or during installation of this product please

call Custom Dynamics® at 1(800) 382-1388.

Package Contents:

- Dynamic Strips™ Turn Signals (pair)

- ST Harness L/R (1)

- 5/16”-24 X 3/4” Screws (4)

Part Numbers:

ATTENTION

Please read all Information below before Installation

Warning: Disconnect negative battery cable from battery; refer to

owner’s manual. Failure do to so may result in electrical shock, injury

or fire. Secure negative battery cable away from positive side of

battery and all other positive voltage sources on vehicle.

Safety First: Always wear appropriate safety gear including safety

glasses when performing any electrical work. It is highly recom-

mended that safety glasses be worn throughout this installation

process. Be sure vehicle is on level surface, secure and cool.

Important: This product is designed and intended for use as

auxiliary lighting only. It is NOT intended to replace any original

equipment lighting installed on the vehicle and should not be used

for that purpose. This product must be wired so that it does not

interfere with any original equipment lighting.

Note: The location of the factory harness plug may vary from model

to model and year to year. It will be located under the gas tank on

either the left or the right side of the frame support. Consult model

year owners manual to determine where factory plug is located.

Note: Installation of this product requires partial removal of the gas

tank. See owners manual or detailed service manual for instructions

on this procedure. If you are not comfortable performing this task

yourself, have this product installed by a qualified Harley-Davidson

mechanic or dealer.

CD-DS-ST-B

CD-DS-ST-C

CD-DS-ST-CC 1

Refer to the manufacturer detailed service manual for

instructions on removing the gas tank. We are not removing

it all the way, only sliding it back about 5 inches so that we

have access to the 8 pin turn signal harness plug located

on the right side of the bike, highlighted above. It will be

behind the rubber frame cover.

Remove the connector from the connector plate, then plug

the male end of the ST-HARNESS into to the plug. Re-

mount the plug to the connector plate when complete.

Connector

Plate

8 Pin

Connector

Fits: 1999-2017 HD Fatboy® and Slim®

Fits: 1999-2017 HD Heritage and Deluxe® ( stock passing

lamps removed)

Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

12-2016SM

Installation Instructions - Page 2

Identify the LEFT side ST-HARNESS connections labeled

with a sticker marked “L”, they need to be routed over to

the left side of the bike. There is a small hole at the base of

the frame that the harness will run through. Pull the rubber

cover back and insert each red connector one at a time

through the hole, be sure to pull any slack available from

the other side. You may also remove the label.

The wires exiting the ST-HARNESS are paired with shrink

tube coverings. Take the Yellow and black paired wires and

twist them together as shown in the photo. Pair the White

and black wires in the same manner. Repeat for the Right

side connections on the ST-HARNESS.

Push the main part of the ST-HARNESS in behind the

rubber frame cover, leaving the output side of the harness

visible from the outside.

Route the ST-HARNESS output wires in behind the brake

and clutch lines on the frame to ensure they won’t interfere

with them. Re-install the gas tank to the frame by following

the instructions in the detailed manufacturer service

manual. The Harness part of the installation is complete,

we now have our connections for the Dynamic Strips™.

Twist

Pull

Left side of the

bike

Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

09-2017

Installation Instructions - Page 3

Take steps to protect the headlamp before working in this area. We have covered ours with a soft microfiber cloth.

There are 5 components that make up the cover: the front plate, side rails left/right and rear plates left/right. Remove the 3

screws (per side) that secure the fork cover assemblies. Note the screw locations in the photos A & B. The front plate in photo A

will remain fixed on the bike, while the rear plates L/R highlighted in photo B will be removed. Note that only the top screw in the

rear plate needs to be removed. Take care with these parts as they are painted and can chip or scratch easily. Stage removed

pieces so they can be drilled.

Remove

Front Plate

Side Rail

Rear plate

Remove

Remove the tie-wraps that secure the Dynamic Strips™

together and un-wrap the wires. Take the right strip and

place it over the 2 bolts that secure the cover. Using a

suitable pen or pencil, tilt the strip outward, noting the wire

outlet, then mark its location on the edge. Remove the strip,

then carry the mark to the center of the cover, equal points

between the 2 screws. Repeat for the other side.

Use a center punch at the marked location to ensure a

guide for the drill bit. Repeat for the other side.

Using a 1/4” drill bit, drill the side rails using the punch mark made in step 8. Repeat for the other side.

Next, mount side rails back in place and use as a reference to mark and punch the left and right rear covers. Use a

center punch to mark the location before drilling. Remove both side rails and rear covers, then drill each rear cover.

Remount the left and right rear covers back in place and use as a reference to mark and punch each side of the

front cover. Use a center punch to mark the location before drilling. Do not drill the front cover yet, there are special

instructions on the next page.

Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

09-2017

Installation Instructions - Page 4

Note that there is a gap between the front plate and the

fork. Using the side rail, turn it over so that the back side is

facing outward (the side you don’t see when installed), then

insert it in behind the front cover at the drill site. This will

protect the fork from being punctured by the drill bit. Drill

the holes with the same 1/4” drill bit.

11 12

Now that the drilling is complete, we must make sure that

there are no sharp rough edges on all parts of the cover that

could cut the wires from the Dynamic Strips™. Using a

de-burring tool like the one pictured, or a small circular metal

file, ream the holes to remove any debris.

Pair the right side strip with the right side rail, insert the wire through the rail. Make sure that the rail is oriented with the curve facing

outward (as if mounted on the bike) toward the strip. Remove the red backing from the 3M tape, then align the screw holes by line

of sight. Once properly aligned, press into place. Repeat for the other side.

Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

09-2017

Installation Instructions - Page 5

Install the rear cover back to the bike. Insert the wires from the Dynamic Strip™ into the holes in the covers. Pull wire slack though

the other side. Repeat this for the other side. Route the wires to the ST-HARNESS connectors.

Using the included mounting screws, secure the Dynamic Strip™ to the bike. Keep an eye on the strips as they are tightened, over

torqueing can cause the them to bow. Do not over tighten, see detailed service manual for torque specs. Repeat for the other side.

Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

09-2017

Installation Instructions - Page 6

Purple = Left Turn (Yellow LEDs)

Black = Left Turn Ground

White = Left Running (white LEDs)

Black = Left Running Ground

Brown = Right Turn (Yellow LEDs)

Black = Right Turn Ground

White = Right Running (white LEDs)

Black = Right Running Ground

Left Turn Harness =Yellow

Left Turn Harness Ground =Black

Left Run Power =White

Left Run Harness Ground =Black

Right Turn Harness =Yellow

Right Turn Harness Ground =Black

Right Run Power=White

Left Run Ground =Black

ST-HARNESS

Male Connector

Left

Turn

Right

Turn

To Factory Harness Connector

Posi-Lock™ Connectors

Note: The secondary connector on

the ST-Harness is a pass-through

for the wiring if needed. It is typically

not used in this application.

Left Right

Use the wiring diagram for connecting the Dynamic Strips™ wires to

the ST-HARNESS. You can wrap the red connectors with electrical

tape or they may be covered with heat shrink tubing, though neither is

mandatory.

Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

09-2017

Installation Instructions - Page 7

18 Test function of the Dynamic Strips™. In running mode, The white LEDs will be on. Test the left turn signal.

The white LEDs will turn off and begin flashing in amber LEDs. Disable left turn and the Amber LEDs will turn

off and engage the White LEDs. Perform this with the Right Turn Signals as well.

Note: This is a very IMPORTANT step. DO NOT SKIP.

Grab both sets of wires with the closed end of your fingers and

push them into the back of the fork cover as shown in the photo.

This should give about 5-6 inches of slack in the wires to allow the

handlebars to turn freely. If you desire, tie wraps may be used to

keep the wires in place.

Tuck Wires up

into the rear of

the fork cover

Everything to Light Up Your Ride®

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Custom Dynamics Accessori per motociclette

Custom Dynamics

Custom Dynamics ProBEAM PB-BCM-KIT1 Manuale utente

Custom Dynamics

Custom Dynamics MAGIC STROBES Manuale utente

Custom Dynamics

Custom Dynamics Street Magic Amber Brightsides Guida alla configurazione

Custom Dynamics

Custom Dynamics ProBEAM Dynamic Strips Manuale utente

Custom Dynamics

Custom Dynamics MAGIC-STROBES-HD Manuale utente

Custom Dynamics

Custom Dynamics ProBEAM PB-BCM-KIT1 Manuale utente

Custom Dynamics

Custom Dynamics ProBEAM PB-SCOUT-RR-BR Manuale utente

Custom Dynamics

Custom Dynamics MagicFLEX2 Indian LED War Bonnet Light Kit Manuale di servizio

Custom Dynamics

Custom Dynamics CD-LR-04-R Manuale utente

Custom Dynamics

Custom Dynamics GEN-SMART-TPU -IND Manuale utente

Custom Dynamics

Custom Dynamics TruWrapz Manuale utente

Custom Dynamics

Custom Dynamics Magic Strobes Manuale utente

Custom Dynamics

Custom Dynamics Smart Triple Play GEN-SMART-TPU-SS8 Manuale utente

Custom Dynamics

Custom Dynamics MAGIC-STROBES-HD Manuale utente

Custom Dynamics

Custom Dynamics PROBEAM PB-SS-KIT2 Manuale utente

Custom Dynamics

Custom Dynamics CD-RG-V-AW2-B Manuale utente

Custom Dynamics

Custom Dynamics Street Magic RT Scuff Guard Guida alla configurazione

Custom Dynamics

Custom Dynamics TruBEAM CDTB-45-AW-3B Manuale utente

Custom Dynamics

Custom Dynamics CD-FORK-BCM-AB Manuale utente

Custom Dynamics

Custom Dynamics Road Glide CD-RG-TS-15-B Manuale utente

Custom Dynamics

Custom Dynamics MAGIC-STROBES-SS6 Manuale utente

Custom Dynamics

Custom Dynamics Street Magic M109 Manuale utente

Manuali Accessori per motociclette popolari di altre marche

SRC

SRC B-TRK502-01-01-SL Manuale utente

3M Speedglas 9100 MP Manuale utente

hepco & becker

hepco & becker 6307520 00 01 Manuale utente

HOMCOM

HOMCOM AA0-077 Manuale utente

hepco & becker

hepco & becker 6307558 00 01 Manuale utente

Wunderkind Custom

Wunderkind Custom 106503-F15 Guida utente

Dräger

Dräger HPS 3500 Manuale utente

M-WAVE

M-WAVE SKI Manuale utente

Kuryakyn

Kuryakyn 6212 Manuale utente

hepco & becker

hepco & becker 6507504 00 01 Manuale utente

Tool it

Tool it PROMAX LCD 9.13G Manuale utente

Roof

Roof RO200 CARBON Manuale utente

Kabuto

Kabuto Japan IBUKI Manuale utente

PUIG

PUIG 5051 Manuale utente

rizoma

rizoma ZTH050 Manuale utente

Joubert

Joubert 10001711 Manuale utente

Sperian

Sperian Optrel p420 Manuale utente

SW-Motech

SW-Motech SBL.01.971.10000/B Manuale utente