CyberData 11171 Manuale
The IP Endpoint Company
Installation Quick Reference
VoIP V3 Zone Controller:
4-Port Audio Out
SIP Compliant
011171
Quick Reference 930445B © 2011 CyberData Corporation ALL RIGHTS RESERVED© 2011 CyberData Corporation ALL RIGHTS RESERVED 930445B Quick Reference
Mounting
Contacting CyberData
Drill Hole Size for Anchor Installation: 3/16" (0.1875")
You have the option to use the following mounting template to mark, and then drill two 3/16" (0.1875”) holes for the
plastic ribbed anchors.
To install and mount the V3 Zone Controller:
1. Install the plastic ribbed anchors in the holes, and position the V3 Zone Controller mounting holes over the
anchors.
2. Use the two #6 x 1 1/2" screws to secure the V3 Zone Controller onto the mounting surface.
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Web: http://www.cyberdata.net/support/contactsupportvoip.html
RMA Dept: (831) 373-2601 ext. 136
Email: [email protected]
RMA Status: http://www.cyberdata.net/support/rmastatus.html
Warranty and RMA information is available at the following website:
http://www.cyberdata.net/support/warranty/index.html
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
www.CyberData.net
The VoIP V3 Zone Controller with Audio-Out enables access to existing paging speakers through a VoIP phone system.
The interface is designed to use a standard paging amplifier with audio inputs and supports paging up to 15 zone
groups from a VoIP phone.
Getting Started
• Be sure that you have received all the parts described in the Parts List section.
• Download the VoIP V3 Zone Controller Operations Guide from the following website address:
http://www.cyberdata.net/products/voip/legacyanalog/pagingzonev3/docs.html
Parts List
Product Specifications
Regulatory Compliance FCC Class A, UL 60950, CE
Power Requirement PoE or +48VDC
LAN Speed 10/100 Mbps
Protocol SIP compliant
Part Number 011171
Dimensions 6.11”L x 4.05”W x 1.15” H
Weight 1.2 lbs.
(2) #6 Plastic Ribbed Anchors (2) #6 x 1 1/2" Screws
(1) Mounting Template (see the last page)
(1) Mounting Kit
(1) VoIP Zone Controller - 4-Port Audio Out
© 2011 CyberData Corporation ALL RIGHTS RESERVED 930445B Quick Reference Quick Reference 930445B © 2011 CyberData Corporation ALL RIGHTS RESERVED
Verifying Operations and Settings
To restore the V3 Zone Controller’s factory default
settings:
1. Use a paper clip to press and hold the RTFM
switch while all of the indicator LEDs turn off.
See the picture on the right.
2. Continue to press the RTFM switch until after
the indicator LEDs turn back on.
3. Release the RTFM switch. All of the V3 Zone
Controller settings will be restored to the
factory default settings.
4. The unit reboots.
Front View with LEDs
Back View with RTFM Switch
Status
(GREEN LED)
Power Status
(BLUE LED)
Link
(YELLOW LED)
Activity
(GREEN LED)
The round, BLUE Power Status LED on the front of the V3 Zone Controller comes on indicating that the
power is on.
The square, YELLOW Link LED above the Ethernet port indicates that the network connection has been
established. The Link LED changes color to confirm the auto-negotiated connection speed:
•ThisLEDisYELLOW at 10 Mbps.
•ThisLEDisORANGE at 100 Mbps.
The GREEN Status LED comes on after the device is booted and initialized. This LED blinks when a page
is in progress.
The square, GREEN Activity LED blinks when there is network activity.
Paper clip RTFM switch
Typical Zone Controller Setup Using the V3 Zone Controller
Setting Up the VoIP V3 Zone Controller
Generic PoE Switch
12 34 56
IP Phone
IP PBX Server
VoIP V3 Zone Controller 4-Port Audio Out
Analog Amplifiers Paging Speakers
Non PoE (with 48 VDC power supply)
Chassis Ground
Chassis Ground
PoE
To set up the V3 Zone Controller, connect the
device to your network:
Poe
•ForPoE, plug one end of an 802.3af Ethernet
cable into the V3 Zone Controller Ethernet
port. Plug the other end of the Ethernet cable
into your network. See the figure on the left.
Non-Poe
•ForNon-PoE, connect the V3 Zone Controller
to a 48VDC power supply. See the figure on
the left.
Chassis Ground
• If required, connect the earth grounding wire
to the Chassis Ground. See the figure on the
left.
48VDC
Altri manuali per 11171
2
Altri manuali CyberData Interruttore
CyberData
CyberData 011528 Manuale
CyberData
CyberData KS-1000 Manuale utente
CyberData
CyberData External Hub Manuale utente
CyberData
CyberData Hub Manuale utente
CyberData
CyberData VoIP Zone Controller Manuale
CyberData
CyberData 011539 Manuale
CyberData
CyberData 10630 Manuale utente
CyberData
CyberData 10807 Manuale utente
CyberData
CyberData 011508 Manuale
CyberData
CyberData 011539 Manuale
CyberData
CyberData 10845 Manuale utente
CyberData
CyberData 10845 Manuale utente
CyberData
CyberData 011187 Manuale
CyberData
CyberData 10776 Manuale utente
CyberData
CyberData IBM SI/O Manuale utente
CyberData
CyberData 10807 Manuale utente
CyberData
CyberData 10630 Manuale utente
CyberData
CyberData 4-Port PoweredUSB 2.0 Hub 011006 Manuale utente
CyberData
CyberData 011539 Manuale
CyberData
CyberData RS232 Manuale utente
