CYP CH-1601TXRX Manuale utente

CH-1601TXRX

HDMI/Audio over CAT5e/6/7 Extender with 48V PoH

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means

- electronic, mechanical, magnetic, optical, chemical, manual,

or otherwise - without express written permission and consent from

Cypress Technology.

Version 1.0 November 2014

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack or install or

operate this equipment, and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through

module openings or empty slots, as you may damage parts.

• Do not attach the power supply cabling to building surfaces.

• Do not allow anything to rest on the power cabling or allow it to

be abused by persons walking on it.

• To protect the equipment from overheating, do not block the slots

and openings in the module housing that provide ventilation.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

VR0 20/10/15 Preliminary Release

VR1 01/12/15 Add HDBT Spec. Table

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 1

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Transmitter’s Front Panel..................3

6.3 Receiver’s Front Panel.....................5

6.4 Receiver’s Rear Panel .....................6

6.5 IR Cable Pin Assignment..................8

6.6 D-Sub 9-Pin Assignment...................8

7. Connection Diagram ............................ 9

8. Specications ...................................... 10

8.1 Technical Specication.................10

8.2 CAT5e/6/7 Cable Specication ...11

8.3 HDBT Specication.........................11

8.4 Supported Resolutions...................12

9. Acronyms ............................................. 13

1. INTRODUCTION

This HDMI and Audio over Single CAT5e/6/7 Transmitter and Receiver

set can send uncompressed audio/video along with controls, IP and

USB data over a single run of CAT5e/6/7 cable up to 100m. It has the

added benet of control through the built-in RS-232 and IR ports and

a bidirectional LAN serving connection. There is a bidirectional digital

audio capability that gives users the convenience of an additional

audio connection. This system also allows the connection of any

USB host, enabling a USB connection to up to 2 USB ports, giving the

Receiver the ability to act like a USB hub. The 48V PoH design can

power the Receiver (PD) from the Transmitter (PSE), eliminating the

need for a separate power supply for the Receiver.

2. APPLICATIONS

• 48V PoH from Transmitter (PSE) to Receiver (PD)

• Household entertainment extending and control

• Lecture room display and control

• Showroom display and control

• Meeting room presentation and control

• Classroom display and control

3. PACKAGE CONTENTS

• 1 x HDMI/Audio over CAT5e/6/7 Transmitter

• 1 x CAT5e/6/7 to HDMI/Audio Receiver

• 1 x IR Blaster

• 1 x IR Extender

• 1 x 48 DC Power adaptor

• 1 x Power Cord

• 1 x Operational Manual

4. SYSTEM REQUIREMENTS

Input source equipment such as DVD/Blu-ray player, host PC/Laptop

and HDMI equipped output display (TV or monitor) with amplier or

active speakers.

5. FEATURES

• Supports HDBaseT 2.0 specication supporting over a single CAT6/7

cable up to 100m/328ft and CAT5e cable up to 90m/295ft

• Fully compliant with HDMI 1.4, and compatible with HDMI 2.0 (4K2K

60Hz with 4:2:0)

• Receiver features 2 USB 2.0 ports

• HDMI (with 3D & 4Kx2K support), HDCP and DVI compliant

• HDBaseT 5Play™ convergence: High-Denition (HD) Video and

Audio, 100BaseT Ethernet, PoH and Control (Bidirectional IR/RS-232

pass-through)

• Supports pass-through of audio formats: LPCM2/5.1/7.1CH, Dolby

Digital 2~5.1Ch, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos and

DTS-HD Master Audio

• Supports coaxial cable up to 2 meter with sampling rate up to 48kHz

• Supports Ethernet network connection

• Bidirectional LAN and external digital audio capability

• Supports RS-232 baud rate from 110~115200bps

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Transmitter’s Front Panel

RS 232 IN IR IN 2 IR OUT 1LAN CAT5e/6/7 OUT DC 48V

POWER

UPDATE



7654321

1Update Switch

Switch this deep switch to right for rmware update use, under

normal operation, leave the switch on left.

2RS-232 IN

Connect to a PC or Laptop with D-Sub 9- pin female cable for the

transmission of RS-232 commands.

3IR IN 2

Connect to the supplied IR Extender cable for IR signal reception.

Ensure that remote being used is within the direct line-of-sight of

the IR Extender.

4IR OUT 1

Connect to the supplied IR Blaster Cable for IR signal transmission.

Place the IR Blaster in direct line-of-sight of the equipment to be

controlled.

5LAN

Connect to internet or network service system to this slot or to the

LAN port slot of the equipment device for a total sharing rate of

100Mbps within the link. The yellow LED will illuminate to represent

the link with Receiver is steady, when it blink irregularly it represent

the link error or when not illuminate it means no link with Receiver.

The green LED will illuminate to represent the Ethernet speed is with

100Mbit/s.

6CAT5e/6/7 OUT

Connect to the Receiver unit with CAT5e/6/7 cable for transmission

of all data signals. The yellow LED will illuminate to represent the

link between Transmitter and Receiver is steady, when it blink

irregularly it represent the link error or when not illuminate it means

no link with Receiver. The green LED will illuminate to represent the

PoE activation.

7DC 48V & POWER LED

Plug the 48V DC power supply into the unit and connect the

adaptor to an AC outlet and the LED will illuminate.

6.2 Transmitter’s Rear Panel

HDMI IN COAX AUDIO IN

OUT 1IN

USB

ARC OUT

OFFON

ARC

5 64321

1HDMI IN

Connect to HDMI source equipment such as a DVD or Blu-ray

player.

2USB

Connect from PC or Laptop for data transmit to or control from the

Receiver’s USB slots.

3COAX OUT 1

Connect to speaker with coaxial input for audio signal output from

Receiver’s COAX IN 1.

4COAX IN 2

Connect to audio source equipment such as DVD or Blu-ray player

for audio signal sending to Receiver’s COAX OUT2.

5AUDIO IN L/R

Connect with audio source equipment such as PC or CD player for

audio signal sending to Receiver’s AUDIO OUT L/R.

6ARC OUT ON/OFF

Switch this dip switch to allows ARC (Audio Return Channel)

function to be activate or not. Switch to OFF to disable ARC

function.

Switch to ON allows Receiver's HDMI output/COAX IN audio to be

routed back and output to both HDMI IN and COAX OUT 1 on the

Transmitter side.

Note: When ARC switch to ON, depending on the connected

devices of the HDMI OUT & Coaxial in from Receiver and the

connected device of the HDMI In & Coaxial Out at the Transmitter

the audio format and behavior may be varied. The ARC input/

output transmission distance may be varied too, it is suggested to

use cable within 2 meters long to ensure the best audio quality.

6.3 Receiver’s Front Panel

RS 232 OUT IR IN 1 IR OUT 2LAN CAT5e/6/7 IN

POWER

UPDATE



7654321

1Update Switch

Switch this deep switch to right for rmware update use, under

normal operation, leave the switch on left.

2RS-232 OUT

Connect to the device that is to be controlled (via D-Sub 9-pin

male cable) by RS-232 commands.

3IR IN1

Connect to the supplied IR Extender cable for IR signal reception.

Ensure that remote being used is within the direct line-of-sight of

the IR Extender.

4IR OUT 2

Connect to the supplied IR Blaster cable for IR signal transmission.

Place the IR Blaster in direct line-of-sight of the equipment to be

controlled.

5LAN

Connect to internet or network service system to this slot or to

Altri manuali per CH-1601TXRX

Indice

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente