CYP PU-506-KIT Manuale utente
PU-506-KIT
3-Play HDBaseT™ Extender Kit (2-way IR, RS-232 & HDMI,
up to 100m)
OPERATION MANUAL
3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.01 08/10/13 First release
5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions.......8
6.1 Transmitter Front and Rear Panels....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3 D-Sub 9-Pin Denitions.........................10
6.4 IR Cable Pin Assignment .......................10
7. Connection Diagram .......................... 11
8. Specications...................................... 12
9. Acronyms............................................. 13
6
1. INTRODUCTION
The PU-506-KIT allows uncompressed HDMI signals to be transmitted over
a Single CAT5e/6/7 cable. This solution has the added features of RS-232
and 2-way IR control functionality over the same CAT5e/6/7 cable. These
combined HDMI and control signals can be transmitted up to lengths of
100 metres. Utilise the USB power output from a TV as an optional way
of powering the PU-506-RX receiver unit alternative to a mains power
supply.
2. APPLICATIONS
Domestic HDMI installation
University lecturing systems
Retail showroom systems
Conference presentation and control
3. PACKAGE CONTENTS
1×HDMI over Single CAT5e/6/7 Transmitter
1×HDMI over Single CAT5e/6/7 Receiver
2×IR Blaster
2×IR Extender
1×3.5 mm Mini-jack to RS-232 Female Cable
1×3.5 mm Mini-jack to RS-232 Male Cable
2×5V/2.6 A DC Power Adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as a DVD or Blu-ray player and HDMI
equipped display (TV or monitor). HDMI and CAT5e/5/7 connection
cables.
7
5. FEATURES
Supports all v1.4 HDMI resolutions plus 4k.
Supports uncompressed video/audio up to 10.2Gbps
Common supported resolutions: HDTV: 480p, 576p, 720p, 1080i,
1080p, 1080p24; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA, WUXGA.
HDMI, HDCP & DVI compliant
Supports HDCP repeating and CEC functions
Uncompressed data transfer over single CAT cable (100m - CAT6/7;
80m - CAT5e)
Audio support up to 7.1CH & Dolby TrueHD, DTS-HD
3-Play™ convergence
Compact design
Supports 3D signals
Choose to power the PU-506-RX via the USB output from a TV (Cable
available separately - APC-USB) : * Please note the performance and
consistency of USB power outputs from TV's can vary and cannot be
guaranteed by CYP.
Note: This system was tested with CAT6/23AWG cable. Results may vary
with cables of dierent specications.
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
Power
Link
CAT 5e /6 Out
DC 5V
IR2 Extender
RS232 In IR1 Blaster
HDMI In
RearFront
231 5
46
7
8
1
RS232 In: Connect to a PC/laptop or RS-232 enabled device (with
supplied 3.5 mm mini-jack to D-sub 9-pin adaptor) for the transmission
of RS-232 commands.
2
IR2 Extender: Connect to the supplied IR extender cable for IR signal
reception. Ensure that remote control being used is within the direct
line-of-sight of the IR extender.
3
IR1 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line-of-sight of the
equipment to be controlled.
4
HDMI In: Connect to the HDMI source equipment such as a DVD or
Blu-ray player.
5
DC 5V: Connect the 5V DC power supply to the unit and plug the
adaptor into an AC outlet.
6
Link LED: The yellow LED will illuminate when both the input and
output CAT5e/6/7 signals are connected.
7
Power LED: This green LED will illuminate when the device is
connected to a power supply.
8
CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7
cable for transmission of all data signals.
9
6.2 Receiver Front and Rear Panels
Power
Link
CAT 5e /6 In
DC 5V IR1 Extender
RS232 Out IR2 Blaster
HDMI Out
RearFront
675
18
3
2
4
1
DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
2
Power LED: This green LED will illuminate when the device is
connected to a power supply.
3
Link LED: The yellow LED will illuminate when both the input and
output CAT5e/6/7 signals are connected.
4
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7
cable for transmission of all data signals.
5
RS232 Out: Connect to the device that is to be controlled (with
the supplied 3.5mm mini-jack to D-sub 9-pin adaptor) by RS-232
commands.
6
IR1 Extender: Connect to the supplied IR extender cable for IR signal
reception. Ensure that the remote being used is within the direct line-
of-sight of the IR extender
7
IR2 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line of sight of the
equipment to be controlled.
8
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.
10
6.3 D-Sub 9-Pin Denitions
PIN DEFINE TX/RX
1N/C
2TxD/RxD
3RxD/TxD
4N/C
5GND
6N/C
7N/C
8N/C
9N/C
6.4 IR Cable Pin Assignment
3
1
3
1
2
2
Power 5V
IR Blaster Signal
NC
IR Signal
Power 5V
Grounding
IR Extender
IR Blaster
Altri manuali per PU-506-KIT
1
Indice
Altri manuali CYP Estensione
CYP
CYP SDV-FTX Manuale utente
CYP
CYP PU-USB-AL Manuale utente
CYP
CYP IP-7000TXWP Manuale utente
CYP
CYP PUV-2010TX Manuale utente
CYP
CYP CETH-4USB Manuale utente
CYP
CYP IP-6000TXRX Manuale utente
CYP
CYP AU-1HARC Manuale utente
CYP
CYP CH-1529TX Manuale utente
CYP
CYP PUV-1530TXRX Manuale utente
CYP
CYP CH-506TXPLBD Manuale utente
CYP
CYP PU-HBTPL-ZE Manuale utente
CYP
CYP CDVI-1109TXC Manuale utente
CYP
CYP CDVI-513TXL Manuale utente
CYP
CYP PU-607BDWP-TX Manuale utente
CYP
CYP PU-232 Manuale utente
CYP
CYP PU-1109KIT Manuale utente
CYP
CYP PU-1107-KIT Manuale utente
CYP
CYP CH-1109TXC Manuale utente
CYP
CYP PU-513L-KIT Manuale utente
CYP
CYP CH-1527TX Manuale utente
