D-Link DIR-300 - Wireless G Router Manuale utente

English • Deutsch • Español • Français • Italiano • ??? • Polski • Português • ??????? • Svenska •

???(????)? • ???(??)? •

= D-Link DIR-300 Rev.A = Airlink101 AR430W = Airlink101 AR335W

Contents

1 Initial flashing instruction

1.1 Install RedBoot♦ 1.2 Install DD-WRT♦ 1.3 Recovery and

Upgrade

♦

1.4 Redboot access

script for Windows

♦

1.5 Redboot access

script for Linux

1.5.1 Putty◊ 1.5.2 Telnet◊

♦

•

2 Hardware

2.1 Serial port♦

•

3 Overclocking•

Initial flashing instruction

Warning: Procedure below is valid only for DIR-300 Revision A. Please check carefully the revision

level of your D-Link before flashing

Don't use Builds 21676 - 23503 as it has a restart loop.

See Where do I download firmware? for links.

Windows flashing instruction for the D-Link DIR-300 to DD-WRT (by Brainslayer, modified by Sash,

v24_SP1 specific added by Deepak)

Install RedBoot

configure your local ip to 192.168.20.80 connect your lan cable to the WAN port of the router. plugoff the

power cord and replug it. You must press the RESET key for 5 sec. now enter the redboot using telnet and ip

192.168.20.81 and port 9000. connect your lan cable to the dir300 wan port. you might need several tries

since its only available for 1 second after aprox. 5 sec. of booting (below is a Windows & Linux access script

for an easy way to connect to redboot)

When you succeed you will be rewarded with a RedBoot> prompt.

DIR-300 Info:

IP: 192.168.20.81/255.255.255.0, Gateway: 0.0.0.0

D-Link_DIR-300_rev_A

Initial flashing instruction 1

Default server: 192.168.20.80

now start a local tftp server on your computer and place ap61.ram as well as ap61.rom in the root dir of this

server

back to the redboot enter:

load ap61.ram

now a new temporarily bootloader should start. (on serial console it will display some warning. but you dont

need to care about). It will be waiting for connection at the LAN side of the router, so follow the instructions

that follow. Plug off your cable from the wan port and reconfigure your local (computer) ip to 192.168.1.2 (set

your DHCP server to serve 192.168.1.1 as the only address in the DHCP pool and the TFTP must also be

available at 192.168.1.2). Now you should be pluging on to any of the lan ports. Then connect via telnet to

192.168.1.1 (or to the ip your dhcp server served to the redboot) and port 9000. A DD-WRT> prompt should

welcome you.

IMPORTANT: while doing the following steps. never plugoff the lan cable or the power cord

fis init

About to initialize [format] FLASH image system - continue (y/n)? y

*** Initialize FLASH Image System

... Erase from 0xbffe0000-0xbfff0000: .

... Program from 0x807f0000-0x80800000 at 0xbffe0000: .

ip_address -h 192.168.1.2

IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0

Default server: 192.168.1.2

load -r -b %{FREEMEMLO} ap61.rom

Using default protocol (TFTP)

Raw file loaded 0x80080000-0x800a8717, assumed entry at 0x80080000

fis create -l 0x30000 -e 0xbfc00000 RedBoot

An image named 'RedBoot' exists - continue (y/n)? y

... Erase from 0xbfc00000-0xbfc30000: ...

... Program from 0x80080000-0x800a8718 at 0xbfc00000: ...

... Erase from 0xbffe0000-0xbfff0000: .

... Program from 0x807f0000-0x80800000 at 0xbffe0000: .

reset

now the unit will reboot and the new bootloader will be executed and is waiting for your connection. this will

take 30+ sec.

Install DD-WRT

The following will work for the initial flash AND a recovery

connect to the bootloader with telnet on port 9000 and ip 192.168.1.1 (If you have installed Micro_Redboot

read the wiki page about it first)

now do the following (consider that fis create operations are taking sometimes *several* minutes to finish, in

my particular case it took more than 5 minutes):

D-Link_DIR-300_rev_A

Install RedBoot 2

fis init

ip_address -h 192.168.1.2

load -r -b 0x80041000 linux.bin

fis create linux

fconfig boot_script true

fconfig boot_script_timeout 5

now type fconfig again and configure the bootscript to:

fis load -l linux

exec

and press enter for every other option to confirm the defaults.

Now type reset again. The unit should now boot dd-wrt and work as known from other atheros based

platforms

You are done now. Wait for your router to reboot. It will take about 1-2 minutes. It may blink and reset once

or twice (as noted).

Now open a Browser and connect to address 192.168.1.1 you should be able to see the dd-wrt page.

That's All

Recovery and Upgrade

connect to the bootloader with telnet on port 9000 and ip 192.168.1.1

do the following: (consider that fis create operations are taking sometimes several minutes to finish)

fis init -f

now load the latest linux.bin from your tftp-server:

ip_address -h 192.168.1.2

load -r -b 0x80041000 linux.bin

fis create linux

Redboot access script for Windows

Make a folder and download putty.exe to it

create a file in the same folder called redboot.txt, with the following content:

create a file in the same folder called redboot.bat with the following content:

rem echo off

:start

rem ------------------------------------------------

ping 192.168.20.81 -n 1 -w 1 >NUL

IF ERRORLEVEL 1 goto start

D-Link_DIR-300_rev_A

Install DD-WRT 3

rem putty

rem ------------------------------------------------

break

putty.exe telnet://192.168.20.81:9000 -m redboot.txt

exit

start the bat file and power on the router.....here comes redboot

Redboot access script for Linux

Putty

download putty.exe to c:\ create a file called redboot.txt, with the following content:

create a file called redboot in the same folder with the following content:

#!/bin/bash

echo

echo ""

echo "Enter hostname or ip address: "

read host

while true

if eval "ping -c 1 $host" > /dev/null; then

putty telnet://$host 9000 -m redboot.txt

echo "Router Awake"

break

else

echo "Waiting for Redboot to boot. Press CTRL + C to quit"

sleep 1

done

Make the file executable.

Telnet

If you don't want to install putty for linux, you may use standard telnet and arping. It would be so (replace

eth2 by your ethernet card name):

#!/bin/sh

echo "192.168.20.81 send ip" >> ~/.telnetrc

arping -f 192.168.20.81 -I eth2; telnet 192.168.20.81 9000

D-Link_DIR-300_rev_A

Redboot access script for Windows 4

Hardware

Serial port

3.3V TTL

8,n,1,9600

Overclocking

To overclock your router, see http://www.dd-wrt.com/phpBB2/viewtopic.php?t=30305

D-Link_DIR-300_rev_A

Overclocking 5

Altri manuali per DIR-300 - Wireless G Router

Indice

Altri manuali D-Link Router di rete

D-Link

D-Link DSL-G804V Manuale utente

D-Link

D-Link DVG-7022S Manuale utente

D-Link

D-Link DWR-555 Manuale utente

D-Link

D-Link DES-1005F Manuale utente

D-Link

D-Link DIR-813 Manuale utente

D-Link

D-Link DWR-961 Manuale utente

D-Link

D-Link DSL-2600U Manuale utente

D-Link

D-Link DSL-2500U Manuale utente

D-Link

D-Link SharePort DIR-825 Manuale utente

D-Link

D-Link xStack DGS-3120-24PC Manuale utente

D-Link

D-Link DIR-878 Manuale utente

D-Link

D-Link EXO DIR-1960 Manuale utente

D-Link

D-Link DWR-910 Manuale utente

D-Link

D-Link DVG-7062S Manuale utente

D-Link

D-Link Xtreme N L7-N-R2000 Manuale utente

D-Link

D-Link DES-2108 Manuale utente

D-Link

D-Link DGL-4100 - GamerLounge Broadband Gigabit Gaming... Manuale utente

D-Link

D-Link DSL-2642B Manuale utente

D-Link

D-Link DIR-615 - Wireless N Router Manuale utente

D-Link

D-Link Express EtherNetwork DI-604 Manuale utente

D-Link

D-Link DIR- 878 Manuale utente

D-Link

D-Link DSL-526E Manuale utente

D-Link

D-Link DKT-710 Manuale utente

D-Link

D-Link DIR-615 - Wireless N Router Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza