D-Link DPR-1040 Manuale utente

WIRELESS G

MULTIFUNCTION PRINT SERVER

DPR-1040

Quick Installation Guide+

Руководство по быстрой установке+

Guía de Instalación Rápida+

Guia de Instalação Rápida+

快速安裝指南+

Petunjuk Pemasangan Cepat+

This product can be set up using

any current web browser, such as

Internet Explorer 6 or Netscape

Navigator 7.0

DPR-1040

Wireless G Multifunction

Print Server

5V, 1.2A Power Adapter

Before You Begin

Check Your Package Contents

DPR-1040 Wireless G Multi-Function Print Server

CD-ROM (Software, Manual and Warranty)

Ethernet (CAT5 UTP) Cable

If any of the above items are missing, please contact your reseller.

Using a power supply

with a different voltage

rating will damage this

product and void its

warranty.

Software and specications subject to change without notice.

This Quick Installation Guide provides you with step-by-step instructions to set up your

Multifunction (MFP) Print Server and start your printing tasks. The model you have purchased

may be slightly different from those seen in the illustrations. For more detailed information

regarding the Print Server, please refer to the User’s Manual that is included in your installation

CD.

NOTE: The images and setting values in this manual are FOR YOUR REFERENCE ONLY.

The actual settings and values depend on your Print Server, system and network.

EXTERNAL FEATURES

USB Port

The DPR-1040’s USB port is located on the rear panel. The port can be congured using the

web congurator which allows users to congure settings through their web browser.

The default IP address of the DPR-1040 is automatically acquired from a DHCP server on

the network. If a DHCP server cannot be found the default IP address for the DPR-1040 will

be 192.168.0.10.

NOTE : The PC’s IP address must be in the same subnet as the Print Server’s IP address

for the two devices to communicate. (For example, if the Print server’s IP address is

192.168.0.10, with a subnet mask of 255.255.255.0, then your computer’s IP address

should be 192.168.0.x, where x is a value between 1-254, excluding 10.)

Physical Interfaces

Ethernet Port (LAN)

The Print Server’s rear panel features an RJ-45 port for the connection of a 10/100Mbps

CAT 5 Ethernet cable. The port supports the NWay protocol, allowing the Print Server to

automatically detect or negotiate the transmission speed of the network.

DC Power Connector

The DC power input connector is located on the Print Server’s rear panel and is labeled

DC 5V.

Reset Button (Bottom Panel)

Press and release this button to reset the MFP Server. To restore the device to factory

default settings , press and hold the button for three seconds until the USB LED on the

front panel lights up and then release the button.

Wi-Fi Protected Setup (WPS) Button

Press this button to use WPS to easily connect to a wireless network. For more information

about this button, see Section 5 - Wireless Setup.

WPS Button

USB Port

Reset Button

Ethernet Port (LAN)

DC Power

Connector

LED INDICATORS

The top panel of the Print Server features four LED indicators:

Power

A steady blue light conrms that the Print Server is turned ON.

USB

A steady blue light indicates the printer is online and successfully connected to the print

server. This light will also blink to indicate that data is being transferred between the print

server and printer.

Link/Act

A steady blue light conrms that the Print Server has a connection to an Ethernet network.

This light will also blink when receiving or transmitting data on the network.

Wireless Link/Act

A steady blue light conrms that the Print Server has a connection to a wireless network.

This light will also blink when receiving or transmitting data on the network.

HARDWARE INSTALLATION

WARNING:

There may be conguration problems if the Print Server is turned on without

rst establishing a network connection.

Follow the steps below to avoid any complications during the hardware installation:

1. Confirm that the printer you will use to connect to the DPR-1040 is operating

correctly.

2. When you have conrmed that the printer is operating correctly, switch its power

OFF.

3. Conrm that your network is operating normally.

4. Using a CAT 5 Ethernet cable, connect the DPR-1040 Ethernet Port (labeled LAN)

to the network.

5. While the printer is turned OFF, connect the USB printer cable to the printer and then

to the USB port on the Print Server.

6. Switch on the printer.

7. Insert the power adapter’s output plug into the DC 5V power socket on the rear panel

of the Print Server.

8. Connect the other end of the power adapter into a power outlet. This will supply power

to the Print Server. The blue LED on the Print Server’s front panel should turn on.

PS SOFTWARE INSTALLATION

PS Software (Windows Vista/XP/2003/2000) includes PS-Link. PS-Link can help you

set up your printer for multifunction printing using your manufacturer’s drivers. This utility

can congure additional Print Server settings. Please refer to the user’s manual for more

information.

To install PS Software, insert the included installation CD into your computer’s CD-ROM

drive to initiate the auto-run program.

NOTE: If auto-run does not start you can access the CD-ROM contents in Windows by

clicking My Computer > [CD-ROM Drive Letter].

Installation

The content of the Installation CD-ROM includes:

 – click this to install the PS Software, which contains PS-Link.

 - click this to see the Quick Installation Guide in PDF format for step-by-step

instructions of the print server Installation.

 – click this to see the User Manual in PDF format for more detailed

information regarding the print server.

 – click this to install Acrobat Reader onto your computer. This enables

you to view the manual and Quick Installation Guide in PDF format.

 – click to close the Auto-Run program.

PS SOFTWARE INSTALLATION

After clicking Install PS Software the

following screen will appear.

Click .

To change the default installation

location, click Browse.

Click .

In this screen you can change the name

of the installation folder. The default

name is PS Software.

Click .

PS SOFTWARE INSTALLATION

To finish the installation of the PS

Software, click Finish.

Click Finish.

To access the utility, click Start

> Programs >PS Software

and click PS Link.

WIRELESS SETUP



WEB CONFIGURATOR

WPS simplies the process of connecting to a wireless network to a touch of a button.

To use WPS you must have a WPS compatible wireless router, if you do not then

you will need to manually congure the wireless connection in the web congurator

(see Web Congurator below).

1. After following the hardware installation steps in section 3, ensure your wireless

network is operating normally and that the print server and wireless router are

close by. When ready, press the WPS button located on the side of the DPR-1040.

The blue LED should start ashing repeatedly.

2. Within 120 seconds, press the WPS button located on the wireless router you will

be connecting to. This button may also be located in the wireless router’s web

conguration pages labeled “Push Button Conguration (PBC)”.

3. If successful, a wireless connection will be established between the two devices.

This connection is secure and uses automatically generated encryption keys; you

do not need to remember them.

Note: If you experience problems connecting to a device, please try again, your

devices may be out of range. If you still experience problems, the device you’re

connecting to may be incompatible with the DPR-1040. Also, make sure you are

connecting to a router or access point (AP).

1. After following the hardware installation steps in section 3, ensure your wireless

network is operating normally. When ready, type the IP address of the DPR-1040

into your browser, the default IP address is 192.168.0.10. If this does not work,

use the PS-Link utility to nd out the IP address.

2. Upon accessing the web congurator, click Setup > Wireless Setup.

3. On the next screen, enter the wireless network settings as provided by your

network administrator.

4. Click Apply Settings, the DPR-1040 will restart and the wireless setup is

complete.

Note: If your wireless connection does not work, check that you have entered the

correct network settings into the Wireless Setup screen.

Technical Support

You can nd software updates and user documentation on the D-Link website.

Tech Support for customers in

Australia:

Tel: 1300-766-868

24/7(24Hrs, 7days a week) technical support

http://www.dlink.com.au

e-mail: [email protected]

India:

Tel: 1800-222-002

9.00 AM to 9.00 PM. All days

http://www.dlink.co.in/support/productsupport.aspx

Indonesia, Malaysia, Singapore and Thailand:

Tel: +62-21-5731610 (Indonesia)

Tel: 1800-882-880 (Malaysia)

Tel: +65 6501 4200 (Singapore)

Tel: +66-2-719-8978/9 (Thailand)

24/7, for English Support Only

http://www.dlink.com.sg/support/

e-mail: [email protected]

Korea:

Tel: +82-2-2028-1815

Monday to Friday 9:00am to 6:00pm

http://www.d-link.co.kr

e-mail: [email protected]

New Zealand:

Tel: 0800-900-900

24/7(24Hrs, 7days a week) technical support

http://www.dlink.co.nz

e-mail: [email protected]

Altri manuali per DPR-1040

Indice

Lingue:

Altri manuali D-Link Server di stampa

D-Link

D-Link DP-101P+ Manuale utente

D-Link

D-Link DP 301U Manuale dell'operatore

D-Link

D-Link DPR-2000 Manuale utente

D-Link

D-Link DPR-1020 Manuale utente

D-Link

D-Link AirPlus DP-G310 Manuale utente

D-Link

D-Link DPR-1260 - RangeBooster G Multifunction Print... Manuale utente

D-Link

D-Link DP-300+ Manuale utente

D-Link

D-Link DP-300U Manuale utente

D-Link

D-Link DP-300 Manuale di istruzioni

D-Link

D-Link AirPlus G DP-G321 Manuale utente

D-Link

D-Link AirPlus DP-G310 Manuale utente

D-Link

D-Link DP-300U Manuale utente

D-Link

D-Link AirPlus G DP-G301 Manuale utente

D-Link

D-Link DP-101P - Pocket Ethernet Print Server Manuale utente

D-Link

D-Link DP-311U Manuale utente

D-Link

D-Link Epress EtherNetwork DP-301P+ Manuale utente

D-Link

D-Link DI-713P Manuale utente

D-Link

D-Link AirPlus DP-G310 Manuale utente

D-Link

D-Link DP-313 - Air 802.11b Wireless Print Server Manuale utente

D-Link

D-Link AirPlus G DP-G310 Manuale utente

D-Link

D-Link DP-101P+ Manuale utente

D-Link

D-Link DPR-1061 Manuale utente

D-Link

D-Link DP 301U Manuale utente

D-Link

D-Link DPR-1020 Manuale utente

Manuali Server di stampa popolari di altre marche

Digitus

Digitus DN-13003-1 Manuale utente

Edimax

Edimax PS-1206PWg Manuale utente

Intellinet

Intellinet 509077 Manuale utente

Atlantis Land

Atlantis Land NETSERVER A02-PSU_GX02 Manuale utente

Buffalo

Buffalo LPV4-U2-300S Manuale utente

Zonet

Zonet ZPS1000 Manuale utente

TRENDnet

TRENDnet TEW-P11G Manuale utente

Axis

Axis 140 BJC Manuale utente

HP Jetdirect 280m - 802.11b Wireless Print... Manuale utente

MicroNet

MicroNet SP766W Manuale utente

NETGEAR

NETGEAR PS104 - Hub - EN Manuale utente

Axis

Axis AXIS 1610 Manuale utente

Buffalo

Buffalo LPV4-U2-300S Manuale utente

Axis

Axis 5600+ Manuale utente

LevelOne

LevelOne WPS-9123 Manuale utente

NETGEAR

NETGEAR PS105 Manuale utente

Xerox

Xerox FreeFlow Print Server V9 SP3 Manuale utente

SEH

SEH primos Manuale utente