D-Link DES-1018MP Manuale utente
D E S -10 18M P 1
ENGLISH
CONTENTS OF
PACKAGING
CONTENTS
INTRODUCTION
The D-Link DES-1018MP is a PoE unmanaged switch capable of feeding power to Power over
Ethernet (PoE) devices such as network cameras. The DES-1018MP has 16 ports operating
at 10/100 Mbps ports with 16 PoE ports (Ports 1 to 16). It also has 2 10/100/1000Base-T/SFP
Combo ports ideal for upgrading home and small ofce businesses with limited budgets.
POWER CORD
If any of these items are missing from your packaging, contact
your reseller.
Warning: Using a power adapter with a different voltage rating
will damage and void the warranty of this product.
16 Ports 10/100Mbps PoE + 2 10/100/1000Base-T/SFP
Combo Ports Unmanaged Switch
DES-1018MP
POWER CORD RETAINER
RACK-MOUNT KIT AND RUBBER FEET
QUICK INSTALLATION GUIDE
D E S -10 18M P
2
ENGLISH
PRODUCT
SETUP
BEFORE SETTING UP THE DES-1018MP
Please follow the steps below to set up the switch:
1. Install the DES-1018MP in a cool and dry place. Refer to the Technical Specications for the
acceptable operating temperature and humidity ranges.
2. Install the switch in a site free from strong electromagnetic source, vibration, dust, and direct
sunlight.
3. Leave at least 10 cm of space at the left and right-hand side of the switch for ventilation.
4. Visually inspect the power jack and make sure that it is fully secured to the power adapter.
Do not stack any device on top of the switch.
INSTALL THE POWER CORD RETAINER
To prevent accidental removal of the power cord, it is recommended to install the power cord
retainer together with the power cord.
2. Plug the power cord into the power socket of the
switch.
1. With the rough side facing down, insert the tie into the
hole below the power socket.
D E S -10 18M P 3
ENGLISH
CONNECTING THE DES-1018MP TO YOUR NETWORK
A. POWER
Plug the AC power cord into a free wall socket, then plug the other end into the power outlet
of the DES-1018MP. The Power LED will illuminate conrming that the device has powered
up successfully.
B. PoE PORTS (PORTS 1 - 16)
The PoE ports can supply up to a total PoE budget of 246.4 watts, allowing users to attach
an IEEE 802.3af compliant device to the DES-1018MP.
16 PoE Ports
3. Slide the retainer through the tie until it reaches the
end of the cord.
INSTALL THE POWER CORD RETAINER
4. Wrap the tie of the retainer around the power cord
and back into the retainer to lock it.
Fasten the tie until the power cord is secured.
D E S -10 18M P
4
ENGLISH
LED INDICATORS
The LED indicators allow you to monitor, diagnose, and troubleshoot any potential problem within the
switch, connection, or attached devices.
LED Color Status Description
Power Green Solid light Power on
Off Power off
Link/Act/Speed
10/100/1000Base-T/
SFP Ports (17 to 18)
Green Solid light Secure connection to a 1000 Mbps
Ethernet device is established.
Blinking The port is receiving or transmitting
data.
Amber Solid light Secure connection to a 10/100 Mbps
Ethernet device.
Blinking The port is receiving or transmitting
data.
Off Light off No link
Link/Act/Speed
10/100 Mbps
Ports (1 to 16)
Green Solid light When there is a secure connection (or
link) to 10/100Mbps Ethernet device at
any of the ports.
Blinking When there is reception or transmission
of data occurring at 10/100Mbps.
Off Off No link
PoE
(Ports1 to 16)
Green Solid light The port is successfully connected to a
PoE device and is powering the device
properly.
Red Solid light The PoE port has failed, possibly due
to:
1. PoE total power budget shortage
2. Over current: Exceeds the
power current of powered device's
classication.
3. Short circuit: An intentional short
circuit has been performed on a
powered device.
Off Light off No connection to a PoE device
D E S -10 18M P 5
ENGLISH
TROUBLESHOOTING
SETUP AND CONFIGURATION PROBLEMS
1. WHAT SHOULD I DO IF THE POWER LED DOES NOT LIGHT UP?
- Try unplugging the power cord and plugging it back into the socket.
2. WHAT SHOULD I DO IF A CONNECTED DEVICE IS NOT DETECTED?
- Ensure the Port LED is illuminated or ashing. If not, try using a new LAN cable.
3. WHAT SHOULD I DO IF A POE DEVICE IS NOT POWERED BY THE DES-1018MP?
- Ensure that the PoE device is connected to one of the four PoE enabled ports (1 to 16) and the
connected PoE devices do not exceed the maximum power budget of 246 W.
Altri manuali per DES-1018MP
1
Indice
Altri manuali D-Link Interruttore
D-Link
D-Link NPP-C61BLK242 Manuale utente
D-Link
D-Link DCH-G601W Manuale utente
D-Link
D-Link DGS-3120-24PC-SI Manuale
D-Link
D-Link DES-3250TG Manuale utente
D-Link
D-Link D DGS-3048 DGS-3048 Manuale utente
D-Link
D-Link DUB-H7 - Hub - USB Manuale utente
D-Link
D-Link DGS-1210/ME series Manuale
D-Link
D-Link DES-3252P - Web Smart Switch Manuale utente
D-Link
D-Link DGS-1510-28XMP Manuale utente
D-Link
D-Link xStack Manuale utente
D-Link
D-Link Nuclias DNH-100 Manuale utente
D-Link
D-Link DGS-6600-48TS Manuale utente
D-Link
D-Link xStack DGS-3612G series Manuale utente
D-Link
D-Link DSS-24+ Manuale utente
D-Link
D-Link mydlink DCH-G022 Manuale utente
D-Link
D-Link GO-SW-16G Manuale utente
D-Link
D-Link DGS-8010 Manuale utente
D-Link
D-Link DGS-1008P Manuale utente
D-Link
D-Link DES-3226L Manuale di installazione
D-Link
D-Link QuickMedia DFB-H7 Manuale utente
