D-Link DES-7200 Manuale di istruzioni

. i

DES-7200

Basic Configuration Command

Reference Guide

Version 10.4(3)

DES-7200 CLI Reference Guide

. ii

Revision No.:Version 10.4(3)

Date:

Without our written permission, this document may not be excerpted, reproduced,

transmitted, or otherwise in all or in part by any party in any means.

. iii

Preface

Version Description

This manual matches the firmware version 10.4(3).

Target Readers

This manual is intended for the following readers:

Network engineers

Technical salespersons

Network administrators

Conventions in this Document

1. Universal Format Convention

Arial: Arial with the point size 10 is used for the body.

Note: A line is added respectively above and below the prompts such as caution and note to

separate them from the body.

Format of information displayed on the terminal: Courier New, point size 8, indicating the

screen output. User's entries among the information shall be indicated with bolded

characters.

2. Command Line Format Convention

Arial is used as the font for the command line. The meanings of specific formats are

described below:

Bold: Key words in the command line, which shall be entered exactly as they are displayed,

shall be indicated with bolded characters.

Italic: Parameters in the command line, which must be replaced with actual values, shall be

indicated with italic characters.

[ ]: The part enclosed with [ ] means optional in the command.

{ x | y | ... }: It means one shall be selected among two or more options.

[ x | y | ... ]: It means one or none shall be selected among two or more options.

//:Lines starting with an exclamation mark "//" are annotated.

. iv

3. Signs

Various striking identifiers are adopted in this manual to indicate the matters that special

attention should be paid in the operation, as detailed below:

Caution

Warning, danger or alert in the operation.

Note

Descript, prompt, tip or any other necessary supplement or explanation for

the operation.

Note

The port types mentioned in the examples of this manual may not be

consistent with the actual ones. In real network environments, you need

configure port types according to the support on various products.

The display information of some examples in this manual may include the

information on other series products, like model and description. The details

are subject to the used equipments.

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands

. 1-1

1CLI Authorization

Configuration Commands

1.1 alias

You can use the alias command to configure an alias of a command in the

global configuration mode. Use the no form of the command to remove the alias

of a specified command or all the aliases under one mode.

alias mode command-alias original-command

no alias mode command-alias

Parameter Description

mode Mode of the command represented by

the alias

command-alias Alias of the command

Parameter

description

original-command Syntax of the command represented

by the alias

Default

Settings Some commands in the privileged EXEC mode have

default alias names.

Command

mode Global configuration mode.

Usage

guidelines

The following table lists the default alias of the commands

in the privileged EXEC mode.

Alias Actual Command

h help

p ping

s show

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands

. 1-2

un undebug

The default alias cannot be deleted by the no alias exec

command.

By setting the alias, you can use a word to replace a

command. For example, you can create an alias to

represent the first part of a command, and then type the

rest part of the command.

The mode of the command represented by the alias is the

command mode existing in the current system. In the

global configuration mode, you can use alias ? to list all

the modes under which you can configure alias for

commands.

DES-7200(config)# alias ?

aaa-gs AAA server group mode

acl acl configure mode

bgp Configure bgp Protocol

config globle configure mode

......

The alias also has its help information that is displayed

after * in the following format:

*command-alias=original-command

For example, in the privileged EXEC mode, the default

alias sstands for show. You can enter s? to query the key

words beginning with sand the help information of the

alias.

DES-7200#s?

*s=show show start-chat start-terminal-service

If an alias represents more than one word, the command

will be displayed in brackets. For example, if you set sv

stand for show version in the privileged EXEC mode,

then:

DES-7200#s?

*s=show *sv="show version" show start-chat

start-terminal-service

The alias must begin with the first letter of the command.

The first letter of the command cannot be a space. The

space before the command cannot be used as a valid

alias.

DES-7200# s?

show start-chat start-terminal-service

The command alias also has its help information. For

example, if the alias ia represents ip address in the

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands

. 1-3

interface configuration mode, then:

DES-7200(config-if)#ia ?

A.B.C.D IP address

dhcp IP Address via DHCP

DES-7200(config-if)# ip address

The above help information lists the parameters of ip

address and shows the actual command name.

You must enter an entire alias; otherwise it cannot be

recognized.

Use the show aliases command to show the aliases

setting in the system.

Examples

In the global configuration mode, use def-route to

represent the default route setting of ip route 0.0.0.0

0.0.0.0 192.168.1.1:

DES-7200# configure terminal

DES-7200(config)# alias config def-route ip route 0.0.0.0

0.0.0.0 192.168.1.1

DES-7200(config)#def-route?

*def-route="ip route 0.0.0.0 0.0.0.0 192.168.1.1"

DES-7200(config)# end

DES-7200# show aliases config

globle configure mode alias:

def-route ip route 0.0.0.0 0.0.0.0

192.168.1.1

Command Description

commands show aliases Show the aliases settings.

1.2 privilege

To attribute the execution rights of a command to a command level, use

privilege in the global configuration mode. The no form of this command

recovers the execution rights of a command to the default setting.

privilege mode [all] [level level | reset ]command-string

no privilege mode [all] [level level ]command-string

Parameter Description

mode CLI mode of the command to which

the execution rights are attributed.

all Alias of the command

Parameter

description

level Specify the execution right levels

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands

. 1-4

(0–15) of a command or

sub-commands

reset Restore the command execution rights

to its default level

command-string: Command string to be authorized

Default

Settings N/A.

Command

mode Global configuration mode.

Usage

guidelines

The following table lists some key words that can be

authorized by command privilege in the CLI mode. The

number of command modes that can be authorized may

vary with different devices. In the global configuration

mode, you can use privilege ? to list all CLI command

modes that can be authorized.

Mode Descripton

config Global configuration mode.

exec Privileged EXEC mode

interface Interface configuration mode

ip-dhcp-pool DHCP address pool

configuration mode

keychain KeyChain configuration mode

keychain-key KeyChain-key configuration

mode

time-range Time-Range configuration mode

Examples

Set the password of CLI level 1 as test and attribute the

reload rights to reset the device:

DES-7200(config)#enable secret level 1 0 test

DES-7200(config)#privilege exec level 1reload

After the above setting, you can access the CLI window as

level-1 user to use the reload command:

DES-7200>reload ?

LINE Reason for reload

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands

. 1-5

<cr>

You can use the key word all to attribute all sub-commands

of reload to level-1 users:

DES-7200(config)# privilege exec all level 1 reload

After the above setting, you can access the CLI window as

level-1 user to use all sub commands of the reload

command:

DES-7200>reload ?

LINE Reason for reload

at reload at a specific time/date

cancel cancel pending reload scheme

in reload after a time interval

<cr>

Command Description

commands enable secret Set CLI-level password

1.3 show aliases

To display all the command aliases or aliases in special command modes, run

the show aliases command in the privileged EXEC mode.

show aliases [mode]

Parameter Description

Parameter

description mode Mode of the command represented by

the alias.

Default

Settings N/A.

Command

mode EXEC mode.

Usage

guidelines Show all the configuration of aliases if the command mode

has not been input.

Examples Following example shows the command alias in the EXEC

mode:

DES-7200#show aliases exec

DES-7200 CLI Reference Guide Chapter 1CLI Authorization Configuration Commands

. 1-6

exec mode alias:

h help

p ping

s show

u undebug

un undebug

Command Description

commands alias Set the alias of a command.

Altri manuali per DES-7200

Indice

Altri manuali D-Link Interruttore

D-Link

D-Link DXS-5000-54S Manuale

D-Link

D-Link xStack DGS-3120-24TC Manuale utente

D-Link

D-Link TM DES-6500 Manuale utente

D-Link

D-Link 5000 Series Manuale di istruzioni

D-Link

D-Link GO-SW-5E Manuale di installazione e funzionamento

D-Link

D-Link DGS-108 Manuale utente

D-Link

D-Link DES-3252P - Web Smart Switch Manuale utente

D-Link

D-Link DXS-3250 - xStack Switch - Stackable Manuale utente

D-Link

D-Link GO-SW-5G Manuale utente

D-Link

D-Link DGS-3000 series Manuale utente

D-Link

D-Link DXS-3600 Series Manuale utente

D-Link

D-Link DKVM-410H Manuale utente

D-Link

D-Link DGS-3000-28X/B1A Manuale utente

D-Link

D-Link xStack DGS-3620 Series Manuale utente

D-Link

D-Link DKVM-2KU Manuale utente

D-Link

D-Link DES-3010FA Manuale utente

D-Link

D-Link DGS-1210-52MP Manuale utente

D-Link

D-Link xStack DGS-3120-48PC Manuale utente

D-Link

D-Link 3100 24P - DGS Switch - Stackable Manuale utente

D-Link

D-Link xStack DGS-3420 Series Manuale utente

D-Link

D-Link DES-1005P Manuale utente

D-Link

D-Link DUB-H4 - Hub - USB Manuale utente

D-Link

D-Link DCH-G020 Manuale di installazione e d'uso

D-Link

D-Link DMS-1250 Series Manuale

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuale utente