Daewoo DWD-FD1451 Manuale utente

SPECIFICATIONS

Hose drain Inlet hose Manual Cap holder(3EA)

■ Accessories

■ DWD-FD145X SERIES

DETERGENT CASE

INLET HOSE

HOT

(OPTION) COLD

DOOR

LOWER COVER ADJUSTABLE LEG

HOSE DRAIN

CONTROL PANEL

POWER CORD

POWER SOURCE 220-240V/50-60Hz

DiMENSION (WXDXH) 595mm x 540mm x 850mm

WEIGHT 58 kg

WATER CONSUMPTION 56.1ℓ

POWER CONSUMPTION 2200W

MAXIMUM MASS WASH 7 kg

OF TEXTILE SPIN 7 kg

WASHER TYPE DRUM TYPE (FRONT LOADING WASHING MACHINE)

OPERATING WATER PRESSURE 0.3 ~ 8kgf/cm2(29.4 ~ 784kPa)

MODEL DWD-FD1451/1452/1453/1454/1455

2. INSTALLATION

INSTALLATION

■ Transit bolts

The appliance is fitted with transit bolts to prevent internal damage during transport.

■ Removing transit bolts

1. To prevent internal damage during transport, the

special 3 bolts are locked. Before operating the

washer, remove the bolts along with the rubber

bungs.

• If they are not removed, it may cause heavy

vibration, noise and malfunction.

2. Unscrew the 3 bolts with the 10mm hex wrench

or spanner or cross-tip screwdriver.

Keep the 3 bolts for a later time.

• When the appliance is transported, transit bolts

will be re-used.

3. Close the holes with the caps supplied.

■ Transit bolts

The appliance is fitted with transit bolts to prevent internal damage during transport.

■ Removing transit bolts

INSTALLATION

■ Installation place requirement

■ BS Plug Safety Details (For U.K. User)

Level floor :

Allowable slope under entire washer is 1°.

Power outlet :

Must be with 1.5 meters of entire side of location of

washer. Do not overload the outlet with more than

one appliance.

Additional Clearance :

For wall, door and floor modeling is required.

(10cm : rear / 2cm : right & left side)

Do not place or store laundry products on top of

washer at any times.

They can damage the finish or controls.

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked

with the letter E or by the earth symbol or coloured Green or Green and Yellow.

The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black.

The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or

coloured Red.

If a 13 amp (BS 1363) plug is used, fit a 13amp BS 1362 fuse.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

GREEN AND YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

This appliance must be earthed

INSTALLATION

FOR ORDINARY TAP

6Connect the inlet hose

adapter of the hose to the

water inlet of the washer by

turning it clockwise to be fixed

tightly.

• Please check the rubber

packing present inside the inlet

hose adapter of the hose.

1Pull down the collar

of the inlet hose to

separate it from the

water tap adapter.

2Loosen the four

screws properly in

order to fit into

water tap.

4Remove the tape,

and screw connector

B into connector A

tightly.

5Connect the inlet

hose to the water tap

adapter by pulling

down the collar of the

hose end.

3Fit the water tap adapter into

the water tap and tighten the

four screws evenly while

pushing up the adapter so that

the

rubber packing can stick to the

water tap tightly.

■ Connecting inlet hose

In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve.

Option : Be careful not to confuse hot water inlet and cold water inlet.

FOR SCREW-SHAPED TAP

Connect the inlet hose adapter

to the water inlet of the washer

and turn it to be fixed.

• Check the packing in the inlet.

1Connect the inlet hose

to the water tap

adapter by pulling

down the collar of the

hose end.

Connect the

connector- inlet

supplied if

necessary.

Inlet Hose

Connector D Rubber

Packing

Connector C

Connector

Inlet

Rubber

Packing

Connector D

Connector C

Hose

TAPE

Connector B

Connector A

INSTALLATION

■ Installation of drain hose

• When installing the drain hose in sink, secure

it tightly with a string.

• Proper securing of the drain hose will protect the

floor from damage due to water leakage.

• The drain hose should not be placed higher than

100cm above the floor.

• Proper securing of the drain hose will protect the

floor from damage due to water leakage.

• When the drain hose is too long, do not force

back in to the washer. This will cause

abnormal noise.

■ Installation of drain hose

INSTALLATION

■ Level adjustment

1. The level adjustment of the washing machine

prevents excessive noise and vibration.

Install the washing machine on a solid and even

floor surface, if possible, in a corner of the room.

Note: The wooden floor may cause excessive

vibration.

2. If the floor is uneven, adjust the adjustable leg as

the following.

(Do not insert pieces of wood etc. under legs.)

• Please check whether there is any gap between

four adjustable legs and the floor.

• Turn adjustable legs by the enclosed spanner in

order to adjust the level of the washing machine.

• Make it sure that there is no swaying of the

washing machine and check that the washing

machine is even completely. (use a spirit level)

• After the level adjustment is finished, turn fixing

nuts up tightly so that the washing machine

maintains the adjustment.

leg

Fixing Nut

❈ Diagonal Check

When pushing down the edges of the washing

machine top plate diagonally, the machine should

not move up and down at all.

(Please, check both of two directions)

If machine rocks when pushing the machine top

plate diagonally, adjust legs again.

3. MAINTENANCE

MAINTENANCE

❈Before cleaning the washer interior, unplug the electrical power cord avoid electrical shock hazards.

■ Cleaning your washer

1. Exterior

Proper care of your washer can extend its life.

The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent.

Immediately wipe off any spills. Wipe with damp cloth.

Try not to hit surface with sharp objects.

• Do not use methylated spirits, diluents or similar products.

2. Interior

Dry around the washer door opening, flexible gasket and door glass.

Run washer through a complete cycle using hot water.

Repeat process if necessary.

• Remove hard water deposits using only cleaners labeled as washer safe.

■ Cold condition

If the washer is stored in an area where freezing may occur or moved in freezing temperature,

follow these instructions to prevent damage to the washer.

1. Turn off water supply tap.

2. Disconnect hoses from water supply and drain water from hoses.

3. Plug electrical cord into a properly grounded electrical outlet.

4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into empty wash drum.

Close the door.

5. Set spin cycle and let washer spin for 1minute to drain out all water.

6. Unplug eletrical power cord, dry the drum interior, and close the door.

7. Remove detergent case and dry excessive water from the compartments.

8. Store washer in an upright position.

9. To remove antifreeze from washer after storage, run empty washer through a complete cycle using detergent.

Do not add wash load.

MAINTENANCE

■ Cleaning the water inlet filter

• "IE" error message will blink on the control panel when water does not enter the detergent drawer.

• If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged.

• It is therefore a good idea to clean it from time to time.

■ Cleaning the drain pump filter

• The drain filter collects threads and small objects left in the laundry.

• Check regularly that the filter is clean to ensure smooth running of your machine.

CAUTION Be careful when draining if the water is hot.

1. Turn off the

water tap. 2. Unscrew the

water inlet

hose.

3. Clean the filter

using a had

bristle brush.

4. Tighten up the

inlet hose.

1. Open the lower cover(1) by

using a coin. Turn the cap

hose(2) to pull out the hose.

Pull out the hose maximally.

(About 13~14cm.)

Unplug the cap hose(2), allowing

the water to flow out. At this time

use a vessel to prevent water

flowing on to the floor. When

water does not flow any more, turn

the pump filter(3) open to the left.

3. Remove any foreign material

from the pump filter(3). After

cleaning, turn the pump filter

clockwise and insert the cap

hose(2) to the original place.

Close the lower cover.

100

about

13~14cm

about

13~14cm

■ Cleaning the water inlet filter

• "IE" error message will blink on the control panel when water does not enter the detergent drawer.

• If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged.

• It is therefore a good idea to clean it from time to time.

MAINTENANCE

■ Cleaning the detergent case

❈After a while detergents and fabric softeners leave a deposit in the detergent case.

• It should be cleaned from time to time with a jet of running water.

•If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out.

• To facilitate cleanling, the upper part of the fabric softener compartment can be removed.

Inlet box recess

❈Detergent can also accumulate inside the recess which should be cleaned

occasionally with an old toothbrush.

• Once you have finished cleaning, replace the detergent case and run a rinse

cycle without laundry.

MAX

max

MAX

max

■ Cleaning the washing drum

• If you live in a hard water area, limescale may continuously build up in places where it cannot be seen and thus

not easily removed.

• Over time the build up of scale clogs appliances, and if it is not kept in check these may have to be replaced.

• Although the washing drum is made of stainless steel, specks of rust can be caused by small metal articles (paper

clips, safety pins) which have been left in the drum.

• The washing drum should be cleaned from time to time.

• If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine use.

❈Descaler may contain chemicals that may damage part of your washing machine.

❈Remove any spots with a stainless steel cleaning agent.

❈Never use steel wool.

■ Cleaning the detergent case

❈After a while detergents and fabric softeners leave a deposit in the detergent case.

• It should be cleaned from time to time with a jet of running water.

•If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out.

• To facilitate cleanling, the upper part of the fabric softener compartment can be removed.

4. DIRECTION FOR DISASSEMBLY

DIRECTION FOR DISASSEMBLY

DOOR LOCK SWITCH

1) Open the door and remove the gasket clamp. 2) Remove the gasket from the front cabinet.

HEATER AND THERMISTOR

1) Remove five screws on the COVER B and separate

the COVER B from washing machine. 2) Remove the connectors of the HEATER.

3) Remove two screws, and remove the door lock

switch.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Daewoo Rondella

Daewoo

Daewoo DWD-F1011 Manuale utente

Daewoo

Daewoo DWD-FV2021-4 Manuale utente

Daewoo

Daewoo DWM-800C Manuale utente

Daewoo

Daewoo DWD-FU1081 Manuale utente

Daewoo

Daewoo DWF-1095 E Series Manuale utente

Daewoo

Daewoo DWF-204AY Manuale utente

Daewoo

Daewoo DWF-S99NS Manuale utente

Daewoo

Daewoo DWD-M8013 Manuale utente

Daewoo

Daewoo DWF-1089 Manuale utente

Daewoo

Daewoo DWM-7010 Manuale utente

Daewoo

Daewoo DWD-M801X Manuale utente

Daewoo

Daewoo DWF-803 Manuale utente

Daewoo

Daewoo DWD-L100 Series Manuale utente

Daewoo

Daewoo DWC-LU1011 Manuale utente

Daewoo

Daewoo WM812T1WU0BG Manuale utente

Daewoo

Daewoo WFW0A1 Series Manuale utente

Daewoo

Daewoo DWD-WD1132 Manuale utente

Daewoo

Daewoo DWC-UD121X Series Manuale utente

Daewoo

Daewoo DWF-4230 Series Manuale utente

Daewoo

Daewoo DWD-F1011 Manuale utente

Daewoo

Daewoo DWF-200TATC Manuale utente

Daewoo

Daewoo DWF-900M Manuale utente

Daewoo

Daewoo DW-3000 Series Guida all'installazione

Daewoo

Daewoo DWM-200C Manuale utente

Manuali Rondella popolari di altre marche

Tricity Bendix

Tricity Bendix AW 1000 W Guida del prodotto

Panasonic

Panasonic NA-F60L5WRB Manuale utente

GE WSLP1500 Manuale

Electrolux

Electrolux EWF1284EDW Manuale utente

Bosch

Bosch WAN2829BSN Manuale utente

LG TV2516DV3B Manuale utente

LG TH2517DSAV Manuale utente

VESTEL

VESTEL CMH-XL 7510 TE Manuale utente

AEG

AEG 74335 Manuale operativo

Johnson

Johnson JWF721A Manuale utente

Beko

Beko WTE7604XLW0 Manuale utente

Danby

Danby DTT100A1WDB Istruzioni per il montaggio

Amica

Amica WA 14 Ex Manuale utente

Bosch

Bosch WAS28461AU Manuale utente

Miele

Miele PW 6080 Vario Manuale utente

Finlux

Finlux FLX108CF220 Manuale utente

Whirlpool

Whirlpool 3LBR5132AN0 Manuale utente

Beko

Beko WKB 51231 PTMA Manuale utente