Dahua Technology N43AJ52 Manuale utente

Eyeball Network Camera

Quick Start Guide

V1.0.2

ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD

Foreword I

Foreword

General

This Quick Start Guide (hereinafter referred to as "the Guide") introduces the functions,

installation, and operations of the camera.

Safety Instructions

The following categorized signal words with defined meaning might appear in the Guide.

Signal Words

Meaning

WARNING

Indicates a medium or low potential hazard which, if not avoided,

could result in slight or moderate injury.

CAUTION

Indicates a potential risk which, if not avoided, could result in

property damage, data loss, lower performance, or unpredictable

result.

NOTE

Provides additional information as the emphasis and supplement

to the text.

Revision History

No.

Version

Revision Content

Release

Time

V1.0.0

First Release.

March 2018

V1.0.1

Add one more SD installation type in "3.3.3 Installing SD

Card (Optional)."

March 2019

V1.0.1

Revise the device dimension in "3.2 Dimension."

April 2019

Privacy Protection Notice

As the device user or data controller, you might collect personal data of others such as face,

fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be

in compliance with the local privacy protection laws and regulations to protect the legitimate

rights and interests of other people by implementing measures include but not limited to:

providing clear and visible identification to inform data subject the existence of surveillance

area and providing related contact.

About the Guide

The Guide is for reference only. If there is inconsistency between the Guide and the actual

product, the actual product shall prevail.

We are not liable for any loss caused by the operations that do not comply with the Guide.

Foreword II

The Guide would be updated according to the latest laws and regulations of related

regions. For detailed information, see the paper manual, CD-ROM, QR code or our official

website. If there is inconsistency between paper manual and the electronic version, the

electronic version shall prevail.

All the designs and software are subject to change without prior written notice. The product

updates might cause some differences between the actual product and the Guide. Please

contact the customer service for the latest program and supplementary documentation.

There still might be deviation in technical data, functions and operations description, or

errors in print. If there is any doubt or dispute, please refer to our final explanation.

Upgrade the reader software or try other mainstream reader software if the Guide (in PDF

format) cannot be opened.

All trademarks, registered trademarks and the company names in the Guide are the

properties of their respective owners.

Please visit our website, contact the supplier or customer service if there is any problem

occurred when using the device.

If there is any uncertainty or controversy, please refer to our final explanation.

Important Safeguards and Warnings III

Important Safeguards and Warnings

Electrical Safety

All installation and operation should conform to your local electrical safety codes.

The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and

supply power with rated voltage which conforms to Limited power Source requirement

according to IEC60950-1. Please note that the power supply requirement is subject to the

device label.

Make sure the power supply is correct before operating the device.

A readily accessible disconnect device shall be incorporated in the building installation

wiring.

Prevent the power cable from being trampled or pressed, especially the plug, power socket

and the junction extruded from the device.

Environment

Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise it

might cause over brightness or light marks, which are not the device malfunction, and

affect the longevity of Complementary Metal-Oxide Semiconductor (CMOS).

Do not place the device in a damp or dusty environment, extremely hot or cold

temperatures, or the locations with strong electromagnetic radiation or unstable lighting.

Keep the device away from any liquid to avoid damage to the internal components.

Keep the indoor device away from rain or damp to avoid fire or lightning.

Keep sound ventilation to avoid heat accumulation.

Transport, use and store the device within the range of allowed humidity and temperature.

Heavy stress, violent vibration or water splash are not allowed during transportation,

storage and installation.

Pack the device with standard factory packaging or the equivalent material when

transporting the device.

Install the device in the location where only the professional staff with relevant knowledge

of safety guards and warnings can access. The accidental injury might happen to the

non-professionals who enter the installation area when the device is operating normally.

Operation and Daily Maintenance

Do not touch the heat dissipation component of the device to avoid scald.

Carefully follow the instructions in the Guide when performing any disassembly operation

about the device; otherwise, it might cause water leakage or poor image quality due to

unprofessional disassemble. Please contact after-sale service for desiccant replacement if

there is condensed fog found on the lens after unpacking or when the desiccant turns

green. (Not all models are included with the desiccant).

Important Safeguards and Warnings IV

It is recommended to use the device together with lightning arrester to improve lightning

protection effect.

It is recommended to ground the device to enhance reliability.

Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air

blower, or you can wipe the lens gently with soft cloth that moistened with alcohol.

Device body can be cleaned with soft dry cloth, which can also be used to remove

stubborn stains when moistened with mild detergent. To avoid possible damage on device

body coating which could cause performance decrease, do not use volatile solvent such as

alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive

detergent be used.

Dome cover is an optical component, do not touch or wipe the cover with your hands

directly during installation or operation. For removing dust, grease or fingerprints, wipe

gently with moisten oil-free cotton with diethyl or moisten soft cloth. You can also air blower

to remove dust.

Please strengthen the protection of network, device data and personal information by

adopting measures which include but not limited to using strong password, modifying

password regularly, upgrading firmware to the latest version, and isolating computer

network. For some device with old firmware versions, the ONVIF password will not be

modified automatically along with the modification of the system password, and you need

to upgrade the firmware or manually update the ONVIF password.

Use standard components or accessories provided by manufacturer and make sure the

device is installed and maintained by professional engineers.

The surface of the image sensor should not be exposed to laser beam radiation in an

environment where a laser beam device is used.

Do not provide two or more power supply sources for the device unless otherwise specified.

A failure to follow this instruction might cause damage to the device.

Regulatory Information V

Regulatory Information

The regulatory information herein might vary according to the model you purchased. Some

information is only applicable for the country or region where the product is sold.

FCC Information

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

FCC conditions:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause

undesired operation.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device,

pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communication.

For class A device, these limits are designed to provide reasonable protection against

harmful interference in a commercial environment. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

For class B device, these limits are designed to provide reasonable protection against

harmful interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

Table of Contents VI

Table of Contents

Foreword.................................................................................................................................................... I

Important Safeguards and Warnings.................................................................................................... III

Regulatory Information............................................................................................................................V

1 Introduction............................................................................................................................................ 1

2 Network Configuration.......................................................................................................................... 2

Initializing Device .......................................................................................................................... 22.1 Modifying Device IPAddress........................................................................................................ 32.2 Logging in Web Interface.............................................................................................................. 42.3

3 Installation.............................................................................................................................................. 5

Packing List................................................................................................................................... 53.1 Dimension..................................................................................................................................... 53.2 Installing Device............................................................................................................................ 73.3 3.3.1 Installation Type.................................................................................................................. 7

3.3.2 Detaching the Enclosure .................................................................................................... 7

3.3.3 Installing SD Card (Optional).............................................................................................. 7

3.3.4 Attaching Device................................................................................................................. 8

3.3.5 Installing Waterproof Connector (Optional)........................................................................ 9

3.3.6 Adjusting Lens Angle........................................................................................................ 10

Introduction 1

1 Introduction

Cable type might vary with different devices, and the actual product shall prevail.

Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit

and water damage. For the detailed operation, see the FAQ Manual.

Cable listFigure 1-1

For more information about cable ports, see Table 1-1.

Table 1-1 Cable information

No.

Port Name

Function

Ethernet port

Connects to network with network cable.



Provides power to the device with PoE.



PoE is available on select models.

12V DC

power input

Inputs 12V DC power. Please be sure to supply power as instructed

in the Guide.

Device abnormity or damage could occur if power is not supplied

correctly.

Network Configuration 2

2 Network Configuration

Device initialization and IP address setting can be finished with the "ConfigTool" or in web

interface. For more information, see the Web Operation Manual.

Device initialization is available on select models, and it is required at first use or after the

device being reset.

Device initialization is available only when the IP addresses of the device (192.168.1.108

by default) and the PC stay in the same network segment.

Plan useable network segment properly to connect the device to the network.

The following figures and interfaces are for reference only, and the actual product shall

prevail.

Initializing Device2.1

Double-click "ConfigTool.exe" to open the tool.Step 1

Click .Step 2

The Modify IP interface is displayed. See Figure 2-1.

Modify IPFigure 2-1

Click Search setting.Step 3 The Setting interface is displayed.

Enter the start IP address and end IP address of the network segment in which youStep 4 want to search devices, and then click OK.

All the devices found in the network segment are listed.

Select one or several devices with Status shows Uninitialized, and then clickStep 5 Initialize.

Network Configuration 3

The Device initialization interface is displayed.

Select the devices that need initialization, and then click Initialize.Step 6 The password setting interface is displayed. See Figure 2-2.

Password settingFigure 2-2

Set and confirm the password of the devices, then enter a valid email address, andStep 7 then click Next.

The final setting interface is displayed.

Password can be modified or reset in System Settings.

Select the options according to your needs, and then click OK.Step 8 The Initialization interface is displayed after initialization is completed. Click the

success icon ( ) or the failure icon ( ) for the details.

Click Finish.Step 9 The device status in the Modify IP interface (Figure 2-1) turns to Initialized.

Modifying Device IP Address2.2

You can modify IP address of one or multiple devices in one time. This section is based on

modifying IP addresses in batch.

Modifying IPaddresses in batch is available only when the corresponding devices have the

same login password.

Do "Step 1" to "Step 4" in "2.1 Initializing Device" to search devices in your networkStep 1 segment.

After clicking Search setting, enter the username and password, and please make

sure they are the same as what you set during initialization, otherwise there will be

"wrong password" notice.

Select the devices which IP addresses need to be modified, and then click Modify IP.Step 2 The Modify IP Address interface is displayed. See Figure 2-3.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Dahua Technology Telecamera di sicurezza

Dahua Technology

Dahua Technology IPC-HFW2531T-ZS-S2 Manuale utente

Dahua Technology

Dahua Technology DH-IPC-HDBW3466FP-AS-AUS Manuale utente

Dahua Technology

Dahua Technology DH-IPC-PFW83242-A180-S2 Manuale utente

Dahua Technology

Dahua Technology N55BS5 Manuale utente

Dahua Technology

Dahua Technology N28BL7Z Manuale utente

Dahua Technology

Dahua Technology IPC-HFW2831T-ZS-S2 Manuale utente

Dahua Technology

Dahua Technology D-TPC-BF1241-B3F4-DW-S2 Manuale utente

Dahua Technology

Dahua Technology IPC-HFW5431E-Z Manuale utente

Dahua Technology

Dahua Technology DH-PSDW8842ML-A180-D237 Manuale utente

Dahua Technology

Dahua Technology IPC-HDW2249TM-S-IL-0280B Manuale utente

Dahua Technology

Dahua Technology IPC-HUM4231S-L4-0280B-S3 Manuale utente

Dahua Technology

Dahua Technology D-IPC-HDBW3841EP-S-0280-S2 Manuale utente

Dahua Technology

Dahua Technology DH-IPC-HDBW3541FP-AS-M-0280B Manuale utente

Dahua Technology

Dahua Technology WizMind IPC-PDBW82041-B360 Manuale utente

Dahua Technology

Dahua Technology IPC-HDB3202-DI Series Manuale utente

Dahua Technology

Dahua Technology N65CB5Z Manuale utente

Dahua Technology

Dahua Technology DH-IPC-HFW3849T1P-AS-PV-S3-BLK Manuale utente

Dahua Technology

Dahua Technology NAVIGATOR X1550 Manuale utente

Dahua Technology

Dahua Technology IPC-HUM8531M-V-LED-0360B Manuale utente

Dahua Technology

Dahua Technology 8A840WANF Manuale utente

Dahua Technology

Dahua Technology IPC-HFW1239DQ-PV-STW Manuale utente

Dahua Technology

Dahua Technology 52C230UNI Manuale utente

Dahua Technology

Dahua Technology Ultra IPC-HFW7442H-Z Manuale utente

Dahua Technology

Dahua Technology Eyeball Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente