Danfoss VLT FC Series Manuale utente

Installation Guide

Control Card VLT® FC Series

1 Introduction

1.1 Compatible Drives

This guide describes the replacement of the control card in:

• VLT® HVAC Drive FC 102.

• VLT® Refrigeration Drive FC 103.

• VLT® AQUA Drive FC 202.

• VLT® AutomationDrive FC 301/FC 302.

• VLT® Lift Drive LD 302.

1.2 Safety Instructions

Only Danfoss authorized, qualified personnel is allowed to repair this equipment.

WARNING

DISCHARGE TIME

The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be

present even when the warning indicator lights are off.

Failure to wait the specified time after power has been removed before performing service or repair work could result in death

or serious injury.

-Stop the motor.

-Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and

DC-link connections to other drives.

-Wait for the capacitors to discharge fully. The minimum waiting time is specified in table Discharge time and is also visible

on the nameplate on top of the drive.

-Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors

are fully discharged.

Table 1: Discharge Time, VLT® HVAC Drive FC 102

Voltage [V] Minimum waiting time (minutes)

4 7 15 20 30 40

200–240 1.1–3.7 kW

(1.50–5 hp)

– 5.5–45 kW

(7.5–60 hp)

– – –

380–480 1.1–7.5 kW

(1.50–10 hp)

– 11–90 kW

(15–121 hp)

– – 315–1000 kW

(450–1350 hp)

AN279051429263en-000101 / 130R0788 | 1

Voltage [V] Minimum waiting time (minutes)

400 – – – 90–315 kW

(121–450 hp)

– –

500 – – – 110–355 kW

(150–500 hp)

– –

525 – – – 75–315 kW

(100–450 hp)

– –

525–600 1.1–7.5 kW

(1.50–10 hp)

– 11–90 kW

(15–121 hp)

– – –

690 – – – 90–315 kW

(100– 350 hp)

– –

525–690 – 1.1–7.5 kW

(1.50–10 hp)

11–90 kW

(15–121 hp)

– 400–1400 kW

(500–1550 hp)

450–1400 kW

(600–1550 hp)

–

Table 2: Discharge Time, VLT® Refrigeration Drive FC 103

Voltage [V] Minimum waiting time (minutes)

4 7 15 20 40

200–240 0.25–3.7 kW

(0.34–5 hp)

– 5.5–37 kW

(7.5–50 hp)

– –

380–480 0.25–7.5 kW

(0.34–10 hp)

– 11–75 kW

(15–100 hp)

110–315 kW

(150–450 hp)

355–450 kW

(500–600 hp)

355–560 kW

(500–750 hp)

525–600 0.75–7.5 kW

(1.0–10 hp)

– 11–75 kW

(15–100 hp)

– –

525–690 – 1.5–7.5 kW

(2–10 hp)

11–75 kW

(15–100 hp)

55–400 kW

(75–400 hp)

450–630 kW

(600–750 hp)

450–800 kW

(600–950 hp)

Introduction

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788

Table 3: Discharge Time, VLT® AQUA Drive FC 202

Voltage [V] Minimum waiting time (minutes)

4 7 15 20 30 40

200–240 0.25–3.7 kW

(0.34–5 hp)

– 5.5–37 kW

(7.5–50 hp)

– – –

380–480 0.25–7.5 kW

(0.34–10 hp)

– 11–75 kW

(15–100 hp)

110–315 kW

(150–450 hp)

– 315–1000 kW

(450–1350 hp)

355–560 kW

(500–750 hp)

525–600 0.75–7.5 kW

(1–10 hp)

– 11–90 kW

(15–121 hp)

– 400–1400 kW

(400–1550 hp)

–

525–690 – 1.1–7.5 kW

(1.5–10 hp)

11–90 kW

(10–100 hp)

75–400 kW

(75–400 hp)

– 450–800 kW

(450–950 hp)

Table 4: Discharge Time, VLT® AutomationDrive FC 301/FC 302

Voltage [V] Minimum waiting time (minutes)

4 7 15 20 30 40

200–240 0.25–3.7 kW

(0.34–5 hp)

– 5.5–37 kW

(7.5–50 hp)

– – –

380–500 0.25–7.5 kW

(0.34–10 hp)

– 11–75 kW

(15–100 hp)

90–200 kW

(150–350 hp)

250–500 kW

(450–750 hp)

250–800 kW

(450–1350 hp)

315–500 kW

(500–750 hp)

400 – – – 90–315 kW

(125–450 hp)

– –

500 – – – 110–355 kW

(150–450 hp)

– –

525 – – – 55–315 kW

(75–400 hp)

– –

525–600 0.75–7.5 kW

(1–10 hp)

– 11–75 kW

(15–100 hp)

– – –

Introduction

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788 | 3

Voltage [V] Minimum waiting time (minutes)

525–690 – 1.5–7.5 kW

(2–10 hp)

11–75 kW

(15–100 hp)

37–315 kW

(50–450 hp)

355–1200 kW

(450–1550 hp)

355–2000 kW

(450–2050 hp)

355–710 kW

(400–950 hp)

690 – – – 55–315 kW

(75–400 hp)

– –

Table 5: Discharge Time, VLT® Lift Drive LD 302

Voltage [V] Minimum waiting time (minutes)

4 15

380–480 0.25–7.5 kW

(0.34–10 hp)

11–75 kW

(15–100 hp)

1.3 Items Supplied

The following is supplied:

• Control card.

1.4 Tools

Only 2 tools are required for replacing the control card:

• Torx 10 screwdriver.

• Flat-head screwdriver.

1.5 More Items Required

• An FC Series drive.

Introduction

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788

2 Replacement

2.1 Overview

e30bf717.11

1LCP 2Blind cover

Illustration 1: LCP and Blind Cover

Replacement

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788 | 5

2.2 Replacing the Control Card

Procedure

1. Remove the LCP and the blind cover.

e30bf718.11

Illustration 2: Removing the LCP

e30bf719.11

Illustration 3: Removing the Blind Cover

2. Remove the LCP cradle.

Replacement

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788

e30bf720.11

Illustration 4: Removing the LCP Cradle

3. Remove all control cables from the metal bracket (spring-loaded).

4. Remove any A, B, or C options that may be installed.

5. Remove the I/O terminals.

e30bf721.12

1Location of A option

3I/O terminals

2Location of B option

Illustration 5: Location of Options and I/O Terminals

6. Unscrew the 3 T10 screws and remove the cable shield.

7. Remove the plastic cover underneath the cable shield.

Replacement

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788 | 7

e30bf722.11

1Cable shield

3T10 screws

2MCO ribbon cable

Illustration 6: Location of the Cable Shield, Screws, and MCO Ribbon Cable (Control Card without MCB 159)

e30bg832.10

Illustration 7: Control Card with MCB 159

8. Unscrew the 2 T10 screws holding the control card EMC shield (4 screws if MCO is installed).

AIf MCO is installed, remove the MCO ribbon cable.

BIf the VLT® Sensorless Safety MCB 159 option is installed, it is not possible to remove the ribbon cable before removing the

control card EMC shield.

Replacement

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788

9. Remove the control card EMC shield.

AIf the MCB 159 is installed, lift the left side of the control card EMC shield first, then lift the right side until it is possible to

remove the MCB 159 ribbon cable. Otherwise, there is a risk to destroy the cable or the connector. When the ribbon cable is

removed, the EMC shield is separated from the control card.

e30bf723.11

1T10 screws 2Control card

Illustration 8: Screws and EMC Shield

10. Unscrew the 3 T10 screws and remove them.

11. Gently remove the control card from the upper-right socket. Avoid overbending and contact with electronic components.

Replacement

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788 | 9

e30bf724.11

Illustration 9: Control Card and T10 Screws

The control card can now be replaced. Reassemble the new control card in reverse order.

Replacement

Installation Guide | Control Card VLT® FC Series

AN279051429263en-000101 / 130R0788

Altri manuali per VLT FC Series

Indice

Altri manuali Danfoss Controllori

Danfoss

Danfoss 4033 Guida

Danfoss

Danfoss ECL Comfort 210 Manuale utente

Danfoss

Danfoss VLT 5000 Series Manuale utente

Danfoss

Danfoss Icon Master Controller 24 V Manuale utente

Danfoss

Danfoss VLT AutomationDrive FC 360 Istruzioni operative

Danfoss

Danfoss KoolKey Manuale utente

Danfoss

Danfoss AMV 110 NL AQT Manuale utente

Danfoss

Danfoss ERC 214 Manuale utente

Danfoss

Danfoss Series 90 Manuale utente

Danfoss

Danfoss AK-SC255 Manuale utente

Danfoss

Danfoss ECL Comfort C31 Manuale utente

Danfoss

Danfoss AK-CC 550A Manuale utente

Danfoss

Danfoss ADAP-KOOL AK-PC 572 Manuale utente

Danfoss

Danfoss AMI 140 Series Manuale utente

Danfoss

Danfoss MCD 500 Series Manuale utente

Danfoss

Danfoss 176F7300 Manuale utente

Danfoss

Danfoss RAE-K Manuale utente

Danfoss

Danfoss AME86 Manuale utente

Danfoss

Danfoss MCO 305 Manuale utente

Danfoss

Danfoss EKC 102C2 Manuale utente

Danfoss

Danfoss AVPA Manuale utente

Danfoss

Danfoss MCI 50-3 I-O Manuale utente

Danfoss

Danfoss 140F1139 Manuale utente

Danfoss

Danfoss AME 56K Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente