Danfoss VLT CDS 803 Manuale utente

Operating Guide

VLT® Compressor Drive CDS 803

Contents

1 Introduction 5

1.1 Purpose of this Operating Guide 5

1.2 Trademarks 5

1.3 Additional Resources 5

1.4 Manual and Software Version 5

1.5 Type Approvals and Certifications 5

1.6 Disposal 6

2 Safety 7

2.1 Safety Symbols 7

2.2 Qualified Personnel 7

2.3 Safety Precautions 7

2.4 Motor Thermal Protection 9

3 Installation 10

3.1 Mechanical Installation 10

3.1.1 Cooling Capacity 10

3.1.2 Side-by-side Installation 10

3.1.3 Drive Dimensions 11

3.2 Electrical Installation 12

3.2.1 Electrical Installation in General 12

3.2.2 IT Grid 12

3.2.3 Mains and Motor Connection 13

3.2.3.1 Introduction 13

3.2.3.2 Connecting to Mains and Motor 14

3.2.3.3 Relays and Terminals on Enclosure Sizes H3–H5 17

3.2.3.4 Relays and Terminals on Enclosure Size H6 18

3.2.4 Fuses and Circuit Breakers 18

3.2.4.1 Branch Circuit Protection 18

3.2.4.2 Short-circuit Protection 18

3.2.4.3 Overcurrent Protection 18

3.2.4.4 UL/Non-UL Compliance 19

3.2.4.5 Recommendation of Fuses 19

3.2.5 EMC-correct Electrical Installation 19

3.2.6 Control Terminals 21

3.2.6.1 Accessing the Control Terminals 21

3.2.6.2 Setting the Control Terminals to Run the Compressor 21

3.2.7 Electrical Wiring 22

ContentsOperating Guide | VLT® Compressor Drive CDS 803

4 Programming 24

4.1 Local Control Panel (LCP) 24

4.2 Start-up Quick Guide for Open-loop Applications 26

4.3 Start-up Quick Guide for Compressor Functions 30

4.4 Start-up Quick Guide for Compressor Closed-loop Applications 31

4.5 Changes Made 36

4.6 Changing Parameter Settings 37

4.7 Accessing All Parameter via the Main Menu 37

4.8 Main Menu Structure 38

5 Troubleshooting 40

5.1 Acoustic Noise or Vibration 40

5.2 List of Warnings and Alarms 40

6 Specifications 43

6.1 Mains Supply 3x200–240 V AC 43

6.2 Mains Supply 3x380–480 V AC 43

6.3 EMC Emission Test Results 44

6.4 Special Conditions 45

6.4.1 Derating for Ambient Temperature and Switching Frequency 45

6.4.2 Derating for Low Air Pressure and High Altitudes 45

6.5 General Technical Data 46

6.5.1 Protection and Features 46

6.5.2 Mains Supply (L1, L2, L3) 46

6.5.3 Compressor Output (U, V, W) 46

6.5.4 Cable Lengths and Cross-sections 46

6.5.5 Digital Inputs 47

6.5.6 Analog Inputs 47

6.5.7 Analog Outputs 47

6.5.8 Digital Outputs 48

6.5.9 Control Card, RS485 Serial Communication 48

6.5.10 Control Card, 24 V DC Output 48

6.5.11 Relay Outputs, Enclosure Sizes H3–H5 48

6.5.12 Relay Outputs, Enclosure Size H6 49

6.5.13 Control Card, 10 V DC Output 49

6.5.14 Ambient Conditions 49

6.6 Options for VLT® Compressor Drive CDS 803 50

ContentsOperating Guide | VLT® Compressor Drive CDS 803

1 Introduction

1.1 Purpose of this Operating Guide

This operating guide provides information for safe installation and commissioning of the AC drive. It is intended for use by qualified

personnel. Read and follow the instructions to use the drive safely and professionally. Pay particular attention to the safety instructions

and general warnings. Always keep this operating guide available with the drive.

1.2 Trademarks

VLT® is a registered trademark for Danfoss A/S.

1.3 Additional Resources

Other resources are available to understand advanced drive functions and programming.

• The programming guide provides greater detail on working with parameters and shows many application examples.

• The design guide provides detailed information about capabilities and functionality to design motor control systems.

• Supplementary publications and manuals are available from Danfoss.

See www.danfoss.com for supplementary documentation.

VLT® Motion Control Tool MCT 10 software support

Download the software from the Service and Support download page on www.danfoss.com.

During the installation process of the software, enter CD-key 34544400 to activate the CDS 803 functionality. An activation key is not

required for using the CDS 803 functionality.

The latest software does not always contain the latest updates for the drive. Contact the local sales office for the latest drive updates (in

the form of *.upd files), or download the drive updates from the Service and Support download page on www.danfoss.com.

1.4 Manual and Software Version

This manual is regularly reviewed and updated. All suggestions for improvement are welcome.

Table 1: Manual and Software Version

Edition Remarks Software version

AQ321748767627xx-xx0101 New power sizes added to product range. 6.0–10 kW (8–15 hp): Version 2.0

18–30 kW (25–40 hp): Version 1.00

1.5 Type Approvals and Certifications

The following list is a selection of possible type approvals and certifications for VLT® Compressor Drive CDS 803 drives:

Introduction

Operating Guide | VLT® Compressor Drive CDS 803

AQ321748767627en-000101 / 130R0570| 5

Name of certification Certification logo IP20

EC Declaration of Conformity ✓

UL listed ✓

UL recognized (only valid for CDS 803 - S096) ✓

RCM ✓

EAC ✓

UkrSEPRO

089

✓

VLT® Compressor Drive CDS 803 drives having S096 in the type code (400 V AC, 18.5–30 kW (25–40 hp)) are certified to UL/EN/IEC

60730-1. The drive is also designed for systems that have to be compliant with UL/IEC/EN 60335.

For more information on UL 508C thermal memory retention requirements, refer to the section Motor Thermal Protection in the

product-specific design guide.

1.6 Disposal

Do not dispose of equipment containing electrical components together with domestic waste.

Collect it separately in accordance with local and currently valid legislation.

Introduction

Operating Guide | VLT® Compressor Drive CDS 803

AQ321748767627en-000101 / 130R0570

2 Safety

2.1 Safety Symbols

The following symbols are used in this manual:

DANGER

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

Indicates information considered important, but not hazard-related (for example, messages relating to property damage).

2.2 Qualified Personnel

To allow trouble-free and safe operation of the unit, only qualified personnel with proven skills are allowed to transport, store,

assemble, install, program, commission, maintain, and decommission this equipment.

Persons with proven skills:

• Are qualified electrical engineers, or persons who have received training from qualified electrical engineers and are suitably

experienced to operate devices, systems, plant, and machinery in accordance with pertinent laws and regulations.

• Are familiar with the basic regulations concerning health and safety/accident prevention.

• Have read and understood the safety guidelines given in all manuals provided with the unit, especially the instructions given in the

Operating Guide.

• Have good knowledge of the generic and specialist standards applicable to the specific application.

2.3 Safety Precautions

WARNING

HIGH VOLTAGE

AC drives contain high voltage when connected to AC mains input, DC supply, or load sharing. Failure to perform installation,

start-up, and maintenance by qualified personnel can result in death or serious injury.

-Only qualified personnel must perform installation, start-up, and maintenance.

Safety

Operating Guide | VLT® Compressor Drive CDS 803

AQ321748767627en-000101 / 130R0570| 7

WARNING

UNINTENDED START

When the drive is connected to AC mains, DC supply, or load sharing, the motor may start at any time. Unintended start during

programming, service, or repair work can result in death, serious injury, or property damage. Start the motor with an external

switch, a fieldbus command, an input reference signal from the local control panel (LCP), via remote operation using MCT 10

software, or after a cleared fault condition.

-Disconnect the drive from the mains.

-Press [Off/Reset] on the LCP before programming parameters.

-Ensure that the drive is fully wired and assembled when it is connected to AC mains, DC supply, or load sharing.

WARNING

DISCHARGE TIME

The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be

present even when the warning indicator lights are off.

Failure to wait the specified time after power has been removed before performing service or repair work could result in death

or serious injury.

-Stop the motor.

-Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and

DC-link connections to other drives.

-Wait for the capacitors to discharge fully. The minimum waiting time is specified in the table Discharge time and is also

visible on the nameplate on top of the drive.

-Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors

are fully discharged.

Table 2: Discharge Time

Voltage [V] Power range [kW (hp)] Minimum waiting time (minutes)

3x200 6.0–10 (8.0–15) 15

3x400 6.0–7.5 (8.0–10) 4

3x400 10–30 (15–40) 15

WARNING

LEAKAGE CURRENT HAZARD

Leakage currents exceed 3.5 mA. Failure to ground the drive properly can result in death or serious injury.

-Ensure the correct grounding of the equipment by a certified electrical installer.

Safety

Operating Guide | VLT® Compressor Drive CDS 803

AQ321748767627en-000101 / 130R0570

WARNING

EQUIPMENT HAZARD

Contact with rotating shafts and electrical equipment can result in death or serious injury.

-Ensure that only trained and qualified personnel perform installation, start-up, and maintenance.

-Ensure that electrical work conforms to national and local electrical codes.

-Follow the procedures in this manual.

CAUTION

INTERNAL FAILURE HAZARD

An internal failure in the drive can result in serious injury when the drive is not properly closed.

-Ensure that all safety covers are in place and securely fastened before applying power.

2.4 Motor Thermal Protection

Context:

This procedure is only valid for VLT® Compressor Drive CDS 803 - S096 (18.2–30 kW/VZH088–VZH170))

Procedure

1. Set parameter 1-90 Motor Thermal Protection to [4] ETR trip 1 to enable the motor thermal protection function.

Safety

Operating Guide | VLT® Compressor Drive CDS 803

AQ321748767627en-000101 / 130R0570| 9

3 Installation

3.1 Mechanical Installation

3.1.1 Cooling Capacity

Table 3: H3–H4, 400 V

Cooling capacity 400 V IP20 enclosure

4 TR/VZH028 H3

5 TR/VZH035 H3

6.5 TR/VZH044 H4

Table 4: H4–H5, 200 V

Cooling capacity 200 V IP20 enclosure

4 TR/VZH028 H4

5 TR/VZH035 H4

6.5 TR/VZH044 H5

Table 5: H5–H6, 400 V

Cooling capacity 400 V IP20 enclosure

13 TR/VZH088 H5

17 TR/VZH117 H5

26 TRVZH170 H6

3.1.2 Side-by-side Installation

The drive can be mounted side by side but requires the clearance specified in table 6 above and below for cooling.

Table 6: Clearance Required for Cooling

Power [kW (hp)] Clearance above/below [mm (in)]

Size IP protection rating 3x200–240 V 3x380–480 V

H3 IP20 – 6.0–7.5 (8.0–10) 100 (4)

H4 IP20 6.0–7.5 (8.0–10) 10 (15) 100 (4)

H5 IP20 10 (15) 18.5–22 (25–30) 100 (4)

H6 IP20 – 30(40) 200 (7.9)

Installation

Operating Guide | VLT® Compressor Drive CDS 803

AQ321748767627en-000101 / 130R0570

Altri manuali per VLT CDS 803

Indice

Altri manuali Danfoss Azionamento CC

Danfoss

Danfoss VLT FC Series Manuale utente

Danfoss

Danfoss VLT 5000 FLUX Manuale utente

Danfoss

Danfoss FCM 300 Series Scheda tecnica

Danfoss

Danfoss RAVV Manuale utente

Danfoss

Danfoss VLT HVAC Drive FC 100 Series Guida

Danfoss

Danfoss VLT HVAC Drive FC 100 Series Guida

Danfoss

Danfoss VACON OPTEA Manuale utente

Danfoss

Danfoss VLT AQUA Drive FC 202 Manuale utente

Danfoss

Danfoss VLT AutomationDrive FC 360 Manuale utente

Danfoss

Danfoss vlt aqua Manuale utente

Danfoss

Danfoss VLT Micro Drive FC 51 Series Manuale utente

Danfoss

Danfoss VLT DriveMotor FCP 106 Manuale utente

Danfoss

Danfoss VLT AutomationDrive FC 361 Manuale utente

Danfoss

Danfoss VLT Midi Drive FC 280 Manuale utente

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuale utente

Danfoss

Danfoss VLT AutomationDrive FC 302 Istruzioni operative

Danfoss

Danfoss AKD 2800 Scheda tecnica

Danfoss

Danfoss VLT 2800 Series Manuale utente

Danfoss

Danfoss HDU-SF Manuale utente

Danfoss

Danfoss ADAP-KOOL Drive Istruzioni operative

Danfoss

Danfoss MCB 152 Manuale utente

Danfoss

Danfoss vlt fcd 302 Manuale utente

Danfoss

Danfoss VLT AQUA Drive FC 202 Guida

Danfoss

Danfoss FC 300 Interbus Manuale utente

Manuali Azionamento CC popolari di altre marche

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuale utente

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuale elenco delle parti

Chamberlain Garog

Chamberlain Garog D Series Manuale utente

Parker

Parker PDS Series Manuale utente

Festo

Festo DGC G Series Guida all'installazione

Binks

Binks QS-5012-1-CE Manuale utente

ABB

ABB ACQ580-01 Series Manuale di installazione

YASKAWA

YASKAWA CANopen SI-S3 Manuale utente

GE D20A6 Manuale utente

Unex

Unex MC-D-250-1000-050W-TW Manuale utente

Geckodrive

Geckodrive G213V Manuale utente

ABB

ABB RSYC-01 Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuale del proprietario

WEG

WEG DeviceNet CFW500 Manuale utente

Siemens

Siemens SINAMICS G Scheda tecnica

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Istruzioni operative

SOMFY

SOMFY JR RU 30 Manuale utente

Beckhoff

Beckhoff AX8911 Manuale dell'operatore