Danfoss DHP-H Manuale utente

Altri manuali per DHP-H

3

Altri manuali Danfoss Pompa di calore

Danfoss

Danfoss DHP-S Eco Manuale utente

Danfoss

Danfoss Optyma Slimpack OP-LSQM Series Manuale utente

Danfoss

Danfoss DHP-H Guida rapida

Danfoss

Danfoss DHP-A Istruzioni operative

Danfoss

Danfoss DHP-AL Manuale utente

Danfoss

Danfoss OPTYMA Plus Series Manuale utente

Danfoss

Danfoss OP-HJZM Manuale

Danfoss

Danfoss DHP-H Varius Pro+ Manuale utente

Danfoss

Danfoss Bluestar Series Manuale utente

Danfoss

Danfoss DHP-AT Manuale utente

Danfoss

Danfoss Optyma Slim Pack OP-LPQE Manuale utente

Danfoss

Danfoss Optyma Slim Pack OP-LPQE Series Manuale utente

Danfoss

Danfoss Optyma OP-MCRN030 Manuale utente

Danfoss

Danfoss DHP-iQ Mini Guida utente

Danfoss

Danfoss Optyma Slim Pack OP-LSHM Series Manuale utente

Danfoss

Danfoss BW10 020-090 Manuale

Danfoss

Danfoss DHP-A Istruzioni operative

Danfoss

Danfoss BW10 020-090 Manuale utente

Danfoss

Danfoss DHP-AT Manuale utente

Danfoss

Danfoss DHP-A Manuale utente

Danfoss

Danfoss DHP-H Guida rapida

Danfoss

Danfoss DHP-A Manuale utente

Danfoss

Danfoss DHP-AQ Manuale utente

Danfoss

Danfoss DHP-AT Guida rapida

Manuali Pompa di calore popolari di altre marche

MICROWELL

MICROWELL HP 1000 GREEN Manuale utente

Sanyo

Sanyo SAP120FCH Manuale utente

Daikin

Daikin EHYHBH05AA Manuale utente

Panasonic

Panasonic WH-SDF03E3E5 Guida

Bryant

Bryant 544B Manuale utente

Airxcel

Airxcel 45000 Series Manuale

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manuale utente

Dimplex

Dimplex LI 16I-TUR Guida utente

Carrier

Carrier WSHP Open v3 Guida rapida alla configurazione

TGM

TGM CTV14CN018A Manuale utente

Carrier

Carrier 38MGQ Series Manuale utente

Kokido

Kokido K2O K880BX/EU Guida alla risoluzione dei problemi

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guida rapida

Carrier

Carrier 48EZN Manuale utente

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Istruzioni operative

Ariston

Ariston NIMBUS Manuale utente

Weishaupt

Weishaupt WWP L 7 Guida utente

GE

GE Zoneline AZ85H09EAC Manuale utente

Electrical

installation instructions

Danfoss Heat Pumps

DHP-H

VWBMF302

DHP-H

Electrical installation – Page 2 VWBMF302

Contents

DHP-H 4, 400V 3N .....................................3–5

DHP-H 6, 400V 3N .....................................6–8

DHP-H 8, 400V 3N ................................... 9-11

DHP-H 10, 400V 3N..............................12–14

DHP-H 12, 400V 3N..............................15–17

DHP-H 16, 400V 3N..............................18–20

DHP-H 4 SP, 230V 1N...........................21–23

DHP-H 6 SP, 230V 1N...........................24–26

DHP-H 8 SP, 230V 1N............................27-29

DHP-H 10 SP, 230V 1N.........................30–32

DHP-H 12 SP, 230V 1N.........................33–35

DHP-H Opti Pro 6, 230V 1N...............36–39

DHP-H Opti Pro 8, 230V 1N...............40–43

DHP-H Opti Pro 10, 230V 1N ............44–47

DHP-H Opti Pro 12, 230V 1N ............48–51

Electrical installation

Danfoss heat pumps are factory-wired internally. The leads that are to

be connected are the mains supply (5-wire DPH or 3-wire DPH SP), out-

door temperature sensor and room sensors (if any).

• All electrical wiring must be carried out by a certified electrician in

compliance with local and national codes and regulations. When in

doubt, contact the local electricity distributor.

• The mains lead is passed through the top of the unit.

• Remove the front panel to get access to the terminal blocks. Connect

the mains lead to the terminal block according to the accompanying

schematic diagram.

• The connection of the heat pump to the mains supply must be hard-

wired and a multi-pole switch

(safety switch) must be installed in the power supply line to the unit.

WARNING! To disconnect the power supply to the heat pump, the

safety switch must be switched off.

NOTE! The cables to the outdoor and indoor sensors carry low voltage.

Interference from surrounding cables may affect these and cause incor-

rect information to be sent to the control unit. It is therefore vitally

important that careful consideration be given to positioning of cables.

Low-voltage cables must be kept well separated from high-voltage

cables. It is important that low-voltage cables are run parallel to high-

voltage cables and separated by a distance of at least 25 cm for cable

lengths up to 100 m. For longer cable lengths, the distance between

cables should be increased.

Important information

Before switching on the power supply to the heat pump, you must

ensure that the heating system, chilled water line and hot water heater

are filled and vented. Otherwise, the circulation pumps can be severely

damaged.

DHP-H

Electrical installation – Page 3

VWBMF302

DHP-H

Electrical installation – Page 4 VWBMF302

DHP-H

Electrical installation – Page 5

VWBMF302

DHP-H

Electrical installation – Page 6 VWBMF302

DHP-H

Electrical installation – Page 7

VWBMF302

DHP-H

Electrical installation – Page 8 VWBMF302

DHP-H

Electrical installation – Page 9

VWBMF302

DHP-H

Electrical installation – Page 10 VWBMF302