Danfoss DHP-R 26 Manuale utente

Danfoss Heat Pumps

DHP-R

Electrical Installation Instructions

VWBME102

VWBMD102Electrical Installation Instructions DHP-R – 2

Danfoss DHP-R 20 . . . . . . . . . . . . . . . . . . . . . 4–10

Danfoss DHP-R 26 . . . . . . . . . . . . . . . . . . . .11–17

Danfoss DHP-R 35 . . . . . . . . . . . . . . . . . . . . 18-24

Danfoss DHP-R 42 . . . . . . . . . . . . . . . . . . . . 25-31

Danfoss DHP-R 21 H . . . . . . . . . . . . . . . . . . 32-38

Danfoss DHP-R 25 H ..................39-45

Electrical Installation

Danfoss DHP-R heat pumps are internally prepared at the factory. The wiring that requires connec-

tion are the power supply (5 core) and the wiring between the outer control cabinets and the heat

pump.

No separate operating voltage needs to be connected to the heat pump, however, if required a

separate operating voltage can be connected to the terminal block marked 2L1 and the bridge

between L1 and 2L1 can be removed. If separate operating voltage is supplied, it must be clearly

marked that external voltage is attached to the heat pump, if the operating power is not connected

through the same circuit breaker as the power supply.

All wiring must be routed according to the applicable regulations under the supervision of an elec-

trician and dimensioned to the applicable regulations, observe any local regulations, contact the

power company if uncertain.

On the rear side at the left-hand lower edge there are cable lead-ins.

The electrical installation must occur with the fixed prelaid cables and an all pole circuit breaker in

the fixed installation.

NOTE! Bridge between terminal block 123 and 124

When connecting a pressure or flow switch in the coolant circuit, remove the bridge between ter-

minal block 123 and 124 (this bridge is connected at the factory)

If the coolant pump is to be started and stopped via separate external switch (passive cooling), this

is connected to terminal block 127-128, potential free connection.

WARNING! The circuit breaker must be switched off to stop the current to the heat pump.

NOTE! The control computer sensor cables transfer small weak currents, ambient interference can

affect them and give incorrect information to the control computer. It is therefore important that

care is taken when laying the cables. The low current cables must be kept well separated from the

high current cables. It is important that the low current cables are routed parallel to the high current

cables and are kept at a distance of at least 25 cm at lengths of up to 100 m, after that the distance

increases.

Contents

VWBMD102 Electrical Installation Instructions DHP-R – 3

Important information

Before the heat pump is supplied with voltage you must ensure that the heating system and coolant

system are filled and bled of air otherwise the circulation pumps can be damaged.

If the electrician wishes to test his connections before the above is carried out, this should only done

when it has been checked that the coolant pump, the condenser pump, the hot gas pump and the

compressor are disconnected.

󰥎

24 VAC 1 must not be connected together with:

• 24 VAC 2

• 24 VDC

• Other equipment that uses 0-10V control signal

• Signal ground GND

24 VAC 2 must only be used as power supply to:

• External equipment that requires 0-10V control

signal

• Auxiliary modules

The two separate 24 VAC circuits must never be connected to each other or to protective ground.

The total power load on 24 VAC 1 respectively 24 VAC 2 must not exceed 50VA.

VWBMD102

Electrical Installation Instructions DHP-R – 4

VWBMD102 Electrical Installation Instructions DHP-R – 5

VWBMD102

Electrical Installation Instructions DHP-R – 6

VWBMD102 Electrical Installation Instructions DHP-R – 7

VWBMD102

Electrical Installation Instructions DHP-R – 8

VWBMD102 Electrical Installation Instructions DHP-R – 9

VWBMD102

Electrical Installation Instructions DHP-R – 10

Questo manuale è adatto per i seguenti modelli

5

Altri manuali Danfoss Pompa di calore

Danfoss

Danfoss Optyma Blue OP-LGHE068NTA07D Manuale utente

Danfoss

Danfoss DHP-A Istruzioni operative

Danfoss

Danfoss DHP-H Guida rapida

Danfoss

Danfoss Optyma Integral Series Manuale utente

Danfoss

Danfoss OPTYMA Plus Series Manuale utente

Danfoss

Danfoss Optyma OP-LPQE Series Manuale utente

Danfoss

Danfoss DHP-AX 6 Manuale utente

Danfoss

Danfoss HHP Series Manuale di istruzioni

Danfoss

Danfoss ECL Comfort 100M Manuale utente

Danfoss

Danfoss Optyma Series Manuale utente

Danfoss

Danfoss DHP-AT Guida rapida

Danfoss

Danfoss DHP-H Varius Pro+ Guida utente

Danfoss

Danfoss DHP-A Manuale utente

Danfoss

Danfoss Optyma OP-UPAC015COP04E Manuale di istruzioni

Danfoss

Danfoss Optyma Plus Manuale utente

Danfoss

Danfoss DHP-R Eco Manuale utente

Danfoss

Danfoss DHP-AL Manuale utente

Danfoss

Danfoss DHP-AQ Mini Istruzioni operative

Danfoss

Danfoss Optyma Trio Series Guida utente

Danfoss

Danfoss DHP-A Manuale utente

Danfoss

Danfoss Optyma OP-MCRN030 Manuale utente

Danfoss

Danfoss Optyma iCO2 Manuale utente

Danfoss

Danfoss OP-LSQM Series Manuale utente

Danfoss

Danfoss DHP-S&DP Manuale utente

Manuali Pompa di calore popolari di altre marche

MICROWELL

MICROWELL HP 1000 GREEN Manuale utente

Sanyo

Sanyo SAP120FCH Manuale utente

Daikin

Daikin EHYHBH05AA Manuale utente

Panasonic

Panasonic WH-SDF03E3E5 Guida

Bryant

Bryant 544B Manuale utente

Airxcel

Airxcel 45000 Series Manuale

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manuale utente

Dimplex

Dimplex LI 16I-TUR Guida utente

Carrier

Carrier WSHP Open v3 Guida rapida alla configurazione

TGM

TGM CTV14CN018A Manuale utente

Carrier

Carrier 38MGQ Series Manuale utente

Kokido

Kokido K2O K880BX/EU Guida alla risoluzione dei problemi

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guida rapida

Carrier

Carrier 48EZN Manuale utente

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Istruzioni operative

Ariston

Ariston NIMBUS Manuale utente

Weishaupt

Weishaupt WWP L 7 Guida utente

GE

GE Zoneline AZ85H09EAC Manuale utente