Danfoss RET2000B-RF + RX1-S Manuale utente

RET2000B-RF + RX1-S

Electronic digital RF thermostat with LCD

User Guide

Danfoss Heating

RET2000

For a large print version of these instructions

please call Marketing on 0845 121 7400.

Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other

printed material. All trademarks in this material are property of the respective companies.

Danfoss Heating 3

Thank you for buying a Danfoss product GB

Vielen Dank für den Kauf eines Produkts von Danfoss

Tak, fordi du valgte et produkt fra Danfoss

Le agradecemos que haya comprado un producto de

Danfoss

Merci d’avoir choisi un produit Danfoss

Hartelijk dank voor de aanschaf van een Danfoss-product

     Danfoss

Br Danfoss ürünü satın aldığınız çn teşekkür ederz

RET2000

What is a room thermostat?

... an explanation for householders. A room thermostat simply switches

the heating system on and o as necessary. It works by sensing the

air temperature, switching on the heating when the air temperature

falls below the thermostat setting, and switching it o once this set

temperature has been reached.

Turning a room thermostat to a higher setting will not make the

room heat up any faster. How quickly the room heats up depends on

the design of the heating system, for example, the size of boiler and

radiators.

Neither does the setting aect how quickly the room cools down.

Turning a room thermostat to a lower setting will result in the room

being controlled at a lower temperature, and saves energy.

Danfoss Heating 5

The heating system will not work if a timeswitch or programmer has

switched it o.

The way to set and use your room thermostat is to nd the lowest

temperature setting that you are comfortable with, and then leave it

alone to do its job.The best way to do this is to set the room thermostat

to a low temperature – say 18°C – and then turn it up by one degree

each day until you are comfortable with the temperature. You won’t

have to adjust the thermostat further. Any adjustment above this

setting will waste energy and cost you more money.

If your heating system is a boiler with radiators, there will usually

be only one room thermostat to control the whole house. But you

can have dierent temperatures in individual rooms by installing

thermostatic radiator valves (TRVs) on individual radiators. If you don’t

haveTRVs, you should choose a temperature that is reasonable for the

whole house. If you do have TRVs, you can choose a slightly higher

setting to make sure that even the coldest room is comfortable, then

prevent any overheating in other rooms by adjusting the TRVs.

Room thermostats need a free ow of air to sense the temperature,

so they must not be covered by curtains or blocked by furniture.

Nearby electric res, televisions, wall or table lamps may prevent the

thermostat from working properly.

RET2000

Display

The LCD displays actual room temperature until the Λ or V button

is pressed more than once. To activate the unit’s backlight press

the Λ or V button once, if no further buttons are pressed the

backlight will remain on for 6 seconds.

Temperature

Danfoss Heating 7

Flame: shows when heating output is on

(in heating mode only)

Standby: shows when unit is manual set to standby

Snowake: shows when cooling output is on

(in cooling mode only)

Battery: ashes when battery is low (battery units only)

Padlock: indicates keyboard lock has been set at

installation

Antenna: indicates a paired link is active between the

thermostat and receiver

External Sensor Alarm:

E5 = Sensor short circuit

E6 = Sensor open circuit / missing

RET2000

Thermostat status (heat mode only)

A ame symbol will be lit whenever the thermostat is calling for

heat.

Setting the temperature

Press either the Λ or V buttons, the product backlight will come

on.

Press either the Λ or V button again within 6 seconds, the display

will ash with the current set temperature. While the display is

ashing press the Λ arrow to increase the set temperature to the

required setting or the V arrow to decrease the set temperature.

If no buttons are pressed the display will return to actual

temperature after 4 seconds and the backlight will go out after

6 seconds.

Danfoss Heating 9

Thermostat status (cool mode only)

A snowake symbol will be lit whenever the thermostat is calling

for cooling. If this is seen to ash, the thermostat output is

delayed for a short period to prevent compressor damage.

Thermostat standby

To place the thermostat into standby (o), press the V arrow

twice to enter the temperature setting mode. When in heating

mode press and hold the V arrow until the set temperature

disappears and the standby symbol appears. In cooling mode

press and hold the Λ arrow until the standby symbol appears.

When in standby the thermostat will have no control of the

heating or cooling system.

To exit standby press and hold the Λ arrow (V arrow in cooling

mode) until the required set temperature is ashing on the

display.

RET2000

Manual Override

During normal Thermostat operation the CH button on the

receiver will light when the device is calling for heat (or cooling

depending on mode). Should communication between the

thermostat and receiver fail, manual override is possible by

pressing the CH button once; the heating/cooling system will

remain on during manual override as indicated by the lit CH

button. Press CH button again to cancel manual override. When

communication is re-established the thermostat and receiver

will return to automatic control.

Warning – Leaving the system in manual override will result in

the boiler heating continually and will result in higher energy

usage.

Altri manuali per RET2000B-RF + RX1-S

Indice

Altri manuali Danfoss Termostato

Danfoss

Danfoss TPOne-M Manuale utente

Danfoss

Danfoss TP9000 Manuale utente

Danfoss

Danfoss TP5001 series Manuale utente

Danfoss

Danfoss TP9000 Manuale utente

Danfoss

Danfoss ECL Comfort 210 Manuale utente

Danfoss

Danfoss Devireg 535 Istruzioni utente

Danfoss

Danfoss LX205T Manuale utente

Danfoss

Danfoss RAS-D2 Combi Manuale utente

Danfoss

Danfoss ECtemp 531 Manuale utente

Danfoss

Danfoss Link FT Manuale utente

Danfoss

Danfoss RET 230 HC-1 Manuale utente

Danfoss

Danfoss TP5001 series Manuale utente

Danfoss

Danfoss HC8000 Series Manuale utente

Danfoss

Danfoss ECtemp Smart Manuale utente

Danfoss

Danfoss REP24CO1 Manuale utente

Danfoss

Danfoss RET 230 HCW-3 Manuale utente

Danfoss

Danfoss CET B-RF Istruzioni operative

Danfoss

Danfoss ECL Comfort 310 Manuale utente

Danfoss

Danfoss HC75-1 Manuale operativo

Danfoss

Danfoss RET1000 MD Manuale utente

Danfoss

Danfoss EFET 130 Manuale utente

Danfoss

Danfoss Icon Master Manuale utente

Danfoss

Danfoss RT 14L Manuale utente

Danfoss

Danfoss Icon Master Controller 24 V Manuale utente

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente