Danfoss REP24CO1 Manuale utente
REP24 CO1
GB Installation Instructions
User Instructions
Electronic Proportional Heat / Cool Thermostat
2
Index
INDEX
Installation Instructions 3-6
User Instructions 8
GB
3
Please note
This product should only be installed by a suitably qualied
electrician or heating installer. The installation must comply
with local Building Regulations and wiring Regulations,
including any competent person requirements that may exist.
Installation Instructions
Installation Instructions
Specication
GB
Thermostat features
Temperature Range 10-30°C
Thermostat Heat, Standby, Cool
Selector
Yes
Power Supply 24 Vac ± 15%, 50/60Hz
Fan Output 3 (1) A, 10-230Vac, Type 1B
Control Method P+I, 2k Proportional Band
Dimensions (mm) 110 wide x 90 high x 40 high
Design Standard EN60730-2-9
Rated Impulse Voltage 2.5Kv
Ball Hardness Test 75°C
Control Pollution Situation Degree 2
Temperature Accuracy ±1°C
Control Output 0-10 Vdc
Common Supply 10 - 230 Vac
4
Installation
First remove the wallplate from the back of the unit.
Fix at a height of approximately 1.5m from the oor, away
from draughts or heat sources such as fan-coil outlets,
sunlight or oce equipment.
Installation Instructions
GB
Wiring
Product overview
This thermostat is designed for fan coil and chilled beam
applications alongside proportional valves and actuator systems
where a 0-10v proportional control output is required.
The thermostat also has a single speed fan output.
The operational mode of the fan (auto or continuous) is selected
at time of installation via DIL switches accessible on the rear of
the unit.
When the unit is in standby the fans are switched o.
5
Connection Diagram
Fan 1
COM
0V/
return
1 Speed
Fan
Electronics
Common In
Heating
24 Vac
N
Cool Heat
Cooling
0-10V outputs
or
0V 24V
AB
Installation Instructions
GB
Commissioning
Prior to re-tting the thermostat to the wallplate, the DIL switches
on the rear of the unit must be set to the desired setting.
6
Installation Instructions
GB
Fan Con Fan Auto
Sw On
1
MOT WAX
2
DIL Switch options, shown in factory set position.
DIL Switch Descriptions
Switch 1: Fan Con - Fan will run whenever thermostat is in
heating or cooling mode.
Fan Auto - Fan will run whenever temperature is
0.2°C or more above/below (depending on heat/cool
mode) setpoint. When temperature reaches setpoint,
the fan will switch o.
Switch 2: MOT - Motorised valve actuator selection.
WAX - Wax valve actuator selection.
Mounting thermostat to the wallplate
To mount the thermostat to the wallplate, align the tabs on
the top of the thermostat with the apertures in the wallplate
and hinge the thermostat down, pressing rmly to engage
the securing clip in the wallplate.
7
Locking & limiting
To lock or limit the setting range turn the setting dial to 3 and
remove knob.
Position the locking springs on the rear of the dial to the
desired position and re-mount the knob ensuring that
number 3 on the dial aligns with the reference mark on the
case.
Installation Instructions
GB
8
User Instructions
GB User Instructions
Setting the temperature
Turn the setting dial to the required temperature.
Frost Protection
To activate frost protection, turn the dial below 10°C. Frost
protection becomes active at 8°C. If the temperature in the room
drops below 8°C then the output will activate.
When frost protection is activated the right LED will turn orange.
Standby Mode
In cooling mode, the standard frost protection is not available;
instead there is standby mode. When the dial is turned past 10°C
the unit enters standby mode and cooling will be inactive until the
dial is turned up past 10°C.
9
User Instructions
GB
Heat Mode
Standby Mode
Cool Mode
LED lit green when
thermostat is powered
and fan is in continuous
mode
LED lit orange when fan
is running in auto mode
LED o when setpoint reached
LED red when heating
LED green when cooling
LED orange when frost
protection activated
Temperature setting dial
Frost protection mode
10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Danfoss Termostato
Danfoss
Danfoss RT1 Istruzioni di montaggio
Danfoss
Danfoss ECL Comfort 210 Manuale utente
Danfoss
Danfoss Icon Master Manuale utente
Danfoss
Danfoss ECtemp 550 Manuale utente
Danfoss
Danfoss RESD Series Manuale utente
Danfoss
Danfoss HC8000 Series Manuale utente
Danfoss
Danfoss Icon Master Manuale utente
Danfoss
Danfoss ECtemp 316 Manuale utente
Danfoss
Danfoss KP61 Manuale utente
Danfoss
Danfoss HC75-3 Manuale operativo
Danfoss
Danfoss 060L2150 Manuale utente
Danfoss
Danfoss DEVIreg Touch Manuale utente
Danfoss
Danfoss LX 420 Manuale utente
Danfoss
Danfoss TP4000 Range Manuale utente
Danfoss
Danfoss MTD Istruzioni per il montaggio
Danfoss
Danfoss 140F1080 Manuale utente
Danfoss
Danfoss FP715Si Manuale utente
Danfoss
Danfoss LX205T Manuale utente
Danfoss
Danfoss 100064 Manuale utente
Danfoss
Danfoss DEVI DEVIreg Touch Manuale utente
