Danfoss RET2001RF Manuale utente
Installation Guide
RET2001RF & TP5001RF
RF Room & Programmable Room Thermostats
www.danfoss.com
AN30483490055001-000103 RET2001RF & TP5001RF2
Installation Guide
Full product instructions can be be found at www.danfoss.
com
SIMPLIFIED EU DECLARATION OF CONFORMITY
The simplied EU declaration of conformity referred to in
Article 10(9)
shall be provided as follows:
Hereby, Danfoss A/S declares that the radio equipment type
RET2001RF and TP5001RF are in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address:
https://assets.danfoss.com/approvals/latest/200388/
ID365935467494-0301.pdf
Danfoss Climate Solutions AN30483490055001-000103 3
Installation Guide ...................................4 EN
Manuel d’installation...............................10 FR
Installationsanleitung ..............................16 DE
Installatiehandleiding ..............................22 NL
Installationsvejledning .............................28 DK
Guía de instalación.................................34 ES
Guida all’installazione ..............................40 IT
Kurulum Kılavuzu ..................................46 TR
Montavimo vadovas ...............................52 LT
........................58 RU
Illustrations ...................................64
Installation Guide
AN30483490055001-000103 RET2001RF & TP5001RF4
1. Installation Steps
User Guide can be downloaded from: heating.danfoss.com.
1. Installation must be done by an authorised
electrician.
2. The room thermostat should be installed at approx.
1.5 m above oor and where the eects of sunlight,
draught or other heat sources (eg. TV’s) are avoided,
see g. 1 on page 64.
3. Decide location of RX1-S V2 receiver, ensuring a
minimum space of 30cm from boiler housing. There
must be no large metal objects, such as boiler cases
or other large appliances, in line of sight between
the thermostat and the receiver as this will prevent
RF communication, see g. 1 on page 64.
4. Remove and mount RX1-S V2 back plate direct
to wall or on wall box, and wire as required for
application, see g. 2 on page 64.
5. Locate hooks at top of RX1-S V2 into top of back
plate and lower into position and tighten retaining
screw. Switch on mains power to start RF pairing.
6. Loosen lower retaining screw of thermostat and
carefully remove back plate, see g. 3 on page 64.
7. Insert 2 x AA Alkaline batteries to front part taking
care to insert correctly as indicated. Check RF
connection between Thermostat and RX1-S V2
Receiver before xing in nal position, see RF Pairing
below.
Installation Guide
EN
Danfoss Climate Solutions AN30483490055001-000103 5
Installation Guide
8. Mount back plate direct to wall or on wall box. The
backplate included within the product packaging
should be used for the installation.
9. Locate hooks at top of front part into top of back
plate and lower into position and tighten retaining
screw.
2. Dimensions and Wiring
See g. 4 for dimensions and g. 5 for wiring diagram
on page 65.
EN
AN30483490055001-000103 RET2001RF & TP5001RF6
3.1 RF Pairing
1. Ensure power to RX1-S V2 receiver is switched on
and batteries are inserted into thermostat.
2. Ensure the display is illuminated. If not, press any
button once to illuminate.
3. Press and hold M button on thermostat for 6
seconds until display changes to show setting
options.
4. Release and press M button to navigate through
menu until setting option 10 is shown.
5. Press > button to change setting to 01.
6. Press the upper part of the setting ring for
RET2001RF and for TP5001RF to accept
the setting. RF aerial icon will ash to indicate
thermostat is in learn mode.
7. Press both PROG and CH buttons on RX1-S V2 until
button LEDs ash.
8. If pairing is successful RF icon on thermostat will
stop ashing and remain on.
9. If pairing is not successful, try moving thermostat to
alternative position and retry.
Installation Guide
EN
Danfoss Climate Solutions AN30483490055001-000103 7
Installation Guide
EN
3.2 Legacy - RF Pairing
Use this guide when replacing the RF thermostat only,
existing RX1-S (087N7774) is used for receiver. If both
products are changed follow normal pairing procedure,
see 3.1 RF Pairing, page 6.
• RET2001RF (087N6473)
• TP5001RF (087N7933)
1. Ensure power to the RX1-S receiver is switched on
and batteries are inserted into the thermostat.
2. Ensure the display is illuminated, if not, press any
button once to illuminate it.
3. Press and hold <and Mfor 5 seconds, the RF aerial
icon will start ashing on the thermostat until
paired.
4. Press both PROG and CH buttons on RX1-S until
button LEDS ash.
5. If pairing is successful RF icon on thermostat will
stop ashing and remain on.
6. If pairing is not successful, try moving thermostat to
alternative position and retry.
AN30483490055001-000103 RET2001RF & TP5001RF8
EN 4. Error codes
Display Description
E1 Sensor Failure
EE EEPROM Failure
Lo Measured temperature below 0 °C
Hi Measure temperature above 50 °C
E3 RF Pairing Failed
E4 RF Signal Lost
E5 RF Hardware Failure
E6 Real Time Clock Failure(TP5001RF Only)
5. Technical Specications
Specications RET2001RF /
TP5001RF RX1-S V2
Operating Product is designed
forcontinuoususe
Operating Voltage 2.5–3VDC
(2 x AA alkaline
batteries)
230Vac
50/60Hz
Output - Volt free
Setting temperature
range 5 °C to 35 °C -
Operating temperature
range 0 °C to 40 °C
Installation Guide
Danfoss Climate Solutions AN30483490055001-000103 9
Specications RET2001RF /
TP5001RF RX1-S V2
Battery life 2 years -
Switch rating - 3A (1) at
250Vac
Switch type - 1x SPDT Type
1B
Terminals 1 to 2.5 mm wires
IP rating IP30 (installed)
Load compensation
control Yes -
On/o control Yes -
ErP class Class IV, ef-
ciency gain
2% -
Construction EN60730-2-9 EN60730-1
Pollution degree rating Degree 2
Rated impulse voltage - 4kV
Ball pressure test 75 °C
Dimensions H86 x W86 x
D30 H84 x W84 x
D30
Software classication A
Operating Frequency 433.100-434.750MHz
Maximum radio-
frequency power
transmitted 10dBm
Running and setting
accuracy (forthermostats
with build in timer)
Setting resolution 1 minute.
Accuracy +/- 1 minute per
month.
Installation Guide
AN30483490055001-000103 RET2001RF & TP5001RF10
1. Étapes d’installation
Le guide de l’utilisateur peut être téléchargé sur: heating.danfoss.com.
1. L’installation doit être réalisée par un électricien
agréé.
2. Le thermostat d’ambiance doit être installé à environ
1,50m au-dessus du sol et à l’écart du rayonnement
solaire, des courants d’air et d’autres sources
dechaleur ( téléviseurs, etc.) (voir g. 1 à la page 64).
3. Choisissez l’emplacement du récepteur RX1-S V2,
enassurant un espace minimum de 30cm par rapport
aucapot métalliquede la chaudière. Il ne peut y avoir
de gros objets métalliques, tels que des enveloppes
de chaudière ou d’autres gros appareils, dans la
ligne de visée du thermostat et du récepteur, car ils
risquent d’empêcher la communication radio (RF)
(voir g. 1 à la page 64).
4. Retirez et montez la plaque arrière RX1-S V2
directement au mur ou sur le boîtier mural et câblez
selon les besoins de l’application.
5. Repérez les crochets au sommet du RX1-S V2 dans
lehaut de la plaque arrière, abaissez-les pour
lespositionner et serrez la vis de retenue. Activez
l’alimentation secteur pour démarrer l’appairage RF.
6. Desserrez la vis de retenue inférieure du thermostat
etretirez soigneusement la plaque arrière (voir g. 2
à la page 64).
Manuel d’installation
FR
Altri manuali per RET2001RF
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Lingue:
Altri manuali Danfoss Termostato
Danfoss
Danfoss RT1 Istruzioni di montaggio
Danfoss
Danfoss HC6110-3 Manuale utente
Danfoss
Danfoss Icon Master Manuale utente
Danfoss
Danfoss living connect Manuale utente
Danfoss
Danfoss RESD Series Manuale utente
Danfoss
Danfoss TP5001 series Manuale utente
Danfoss
Danfoss BasicPlus2 WT-D Manuale utente
Danfoss
Danfoss 088L5130 Manuale utente
Danfoss
Danfoss SH-E01 Manuale utente
Danfoss
Danfoss living connect Manuale utente
Danfoss
Danfoss FP715Si Manuale utente
Danfoss
Danfoss REP24 Manuale utente
Danfoss
Danfoss Icon Master Controller 24 V Manuale utente
Danfoss
Danfoss RET-B Manuale utente
Danfoss
Danfoss RET2000 B Manuale utente
Danfoss
Danfoss Icon Master Manuale utente
Danfoss
Danfoss RET2000 B Manuale utente
Danfoss
Danfoss ECL Comfort 210 Manuale utente
Danfoss
Danfoss TP4000 Range Manuale utente
Danfoss
Danfoss DEVIreg Smart Manuale utente
