Datacom Systems DURAstream DS-4000 Guida
July 2014
© 2014 Datacom Systems Inc
541-0152-R.01
DURAstream™1 Gigabit DS-4000
FASTStart Guide
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
What is included?
(1) Model:DS-4000 series Bypass Switch
(1) Console Cable (DB9 to RJ45)
(1) Management Cable (RJ45 to RJ45)
(2) Switching AC Adapters
(2) AC Line Cords
Summary:
Datacom Systems Inc. DURAstream™DS-4000 Bypass Switch is a 1Gbps
intelligent external active bypass that enables plug and play connectivity which
includes an auto heartbeat and requires no additional drivers to be installed on
any connected appliance.
The DS-4000 consists of four 1Gbps segments which can support four network
segments and four appliances. In our example below, we show two network
segments being connected with two systems (typically IPS) using a DS-4000.
If one of the links connected to an appliance segment goes down, the DS-4000
will directly connect the network ports on the segment and bypass the appliance.
This will ensure that the network segment will remain connected even if the
appliance on the segment goes down.
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
Port Layout:
Ports are designated as Network or Appliance Ports as shown below:
Network and Appliance Ports
Default Settings:
SSH
Port: 22
Serial Terminal Settings
Bits per second: 115200
Data bits: 8
Parity: None
Stop: 1
Flow Control: None
Management Port Settings
IP Address: 192.168.0.111
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
User Settings
Username: admin
Password: admin
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
CLI Installation Commands:
Changing Management Port Settings
1. Show the current management port settings
datacom>show management-if
2. Enter configuration mode for management interface.
datacom>configure management-if
3. To configure static IP settings:
datacom(configure-management-if)>ip static <ip address> mask <network mask>
gateway <gateway IP address>
Example:
datacom(configure-management-if)>ip static 10.10.10.10 mask
255.255.255.0 gateway 10.10.10.1
4. To assign the IP settings dynamically:
datacom(configure-management-if)>ip dhcp
Changing Network/Appliance Port Settings:
1. Show the current port settings:
datacom>show links configuration
2. Enter configuration mode for a network or appliance Port:
datacom>configure port portid S3.N2
portid S3.N2
S3 indicates segment 3.
N2 indicates network port 2.
A1 would indicate appliance
port 1.
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
3. To change the port status between up and down:
datacom ports portid S3.N2>link <auto/down>
4. To modify the speed/duplex on the port:
datacom ports portid S3.N2>speed <auto/10M/100M/1G> <auto/full/half>
Example:
datacom ports portid S3.N2>speed 100M full
Changing Segment Settings:
1. Show the current bypass settings:
datacom>show bypass mode
datacom>show bypass status
datacom>show bypass heartbeat
2. Enter configuration mode for a segment:
datacom>configure segment 1
3. Enable/Disable link fault detection:
datacom(segment[1])>lfd <enabled/disabled>
4. Set segment boot-mode:
datacom(segment[1])> boot-mode heartbeat <normal-active-bypass/normal-active-
inline/manual-active-inline/manual-active-bypass-plus/manual-active-bypass/manual-
passive-bypass/auto>
Example:
datacom ports portid S3.N2>bypass boot-mode heartbeat normal-active-bypass
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
GUI Tutorial:
By clicking on the “Management Port” tab on the left side of the page, you can view
the management port fields. Clicking on the blue “Management Port” title at the top will
enter configuration mode.
Page to view Management port settings
Page to edit Management port settings
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
Clicking on the “Ports” section on the left side of the page and then selecting the
“Links” tab will bring up a page that shows the settings for all network and appliance ports
on the DS-4000. To configure the link settings, click on the blue “Links” title at the top of
the page.
Showing statistics for all Network/Appliance ports.
Edit the attributes of Network/Appliance ports.
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
Clicking on the “Segments” tab at the top left of the page will present information on
all of the configurable attributes of segments. To configure a specific segment, click on
one of the blue “Segment #” titles at the top of the screen.
Showing all of the configurable attributes for segments.
Configure the various attributes of a segment.
DS-4000 FASTstart Guide
© 2014 Datacom Systems Inc DURAstream™
Clicking on the “Authentication” tab on the left side of the page and then selecting
“Users” show the admin user. To configure password for admin, click on one of the blue
“admin” title at the top of the screen.
Showing the admin account.
Modifying the password for the admin account.
Indice
Altri manuali Datacom Systems Interruttore
Datacom Systems
Datacom Systems VS-1200-S Series Manuale utente
Datacom Systems
Datacom Systems VS-1212-F Istruzioni per l’uso
Datacom Systems
Datacom Systems DURAstream DS-1010 Manuale utente
Datacom Systems
Datacom Systems DS-1404 Guida
Datacom Systems
Datacom Systems 4X16SP-1000BT Manuale utente
Datacom Systems
Datacom Systems 4X16SP-1000BT Manuale utente
Datacom Systems
Datacom Systems 2X8SP-1000BT Manuale utente
Datacom Systems
Datacom Systems VS-1200 Series Manuale utente
