Datalogic DS2400A Manuale utente

DS2400A QUICK GUIDE

DS2400A

General View: Laser Safety:

The scanner is classified as a Class 2 laser

product according to EN 60825-1 regulations

and as a Class II laser product according to

CDRH regulations.

Disconnect the power supply when opening the

device during maintenance or installation to

avoid exposure to hazardous laser light.

There is a safety device which allows the laser to

be switched on only if the motor is rotating above

the threshold for its correct scanning speed.

The motor and laser beam can be switched off

through a software command (see also the

WinHost Help On Line).

CAUTION-CLASS 3B LASER LIGHT

WHEN OPEN AVOID EXPOSURE TO BEAM

This product conforms to the applicable

requirements of 21CFR1040 at the date

of manufacture.

LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

MAX. OUTPUT RADIATION 1 mW

EMITTED WAVE LENGTH 630~680 nm

TO EN 60825-1:2001

CUS

218441

N246

Figure A

4 8

Power On / Data TX LED

External Trigger LED

Good Read LED

Laser On LED

Warning and Device Class Label

Laser Beam Output Window

ccessory Mounting Holes

Mounting Holes

For further details on product installation, see the

complete Reference Manual on the installation CD-ROM.

DS2400A can be configured through the WinHost

Windows-based software program available on the

installation CD-ROM.

For configuration it is necessary to create a cable

connecting the scanner to the PC as indicated in the

“How To Build A Simple Interface Test Cable” section of

this guide, otherwise you can use the C-Box 100.

Power Supply:

- This product is intended to be installed by Qualified

Personnel only.

- All Models:

This accessory device is intended to be supplied by a UL

Listed or CSA Certified Power Unit with «Class 2» or LPS

power source which supplies power directly to the

scanner via the 25-pin connector.

Warning and Device Class Labels

The laser diode used in this device is classified

as a class 3B laser product according to EN

60825-1 regulations and as a Class IIIb laser

product according to CDRH regulations. As it is

not possible to apply a classification label on

the laser diode used in this device, the following

label is reproduced below.

LASER LIGHT

AVOID EXPOSURE TO BEAM

CLASS 3B LASER PRODUCT

MAX. OUTPUT RADIATION 7 mW

EMITTED WAVE LENGTH 630~680 nm

TO EN 60825-1 (2001)

Laser Diode Class Label

Any violation of the optic parts in particular can

cause radiation up to the maximum level of the

laser diode (7 mW at 630 to 680 nm).

WEEE Compliance:

DS2400A QUICK GUIDE

Model Description:

DS2400A - X X X 0

Reading Range

0 = Short range

1 = Medium range

2 = Long range

Communication Interface

2 = RS232/RS485 main + RS232 aux

Optic Version

0 = Linear

1 = Raster

Reading Performance:

Version Reading Distance Max Code Resolution

mm (mils)

Speed

scans/s

0XX0 75 mm (3 in) - 340 mm (13.4 in) on 0.35 mm (14 mils) codes 0.20 (8) 600 to 1000

1XX0 100 mm (3.9 in) - 440 mm (17.3 in) on 0.50 mm (20 mils) codes 0.25 (10) 600 to 1000

2XX0 190 mm (7.5 in) - 600 mm (23.6 in) on 0.50 mm (20 mils) codes 0.35 (14) 600 to 1000

Technical Features:

ELECTRICAL FEATURES SOFTWARE FEATURES

Power Supply 10 –30 Vdc Readable Codes

Power Consumption 5 W maximum

Main Serial Interface Programmable:

RS232;

RS485 Full-Duplex/Half-

Duplex;

Auxiliary Interface RS232

EAN/UPC

(including Add-on 2 and Add-on 5)

Code 39

2/5 Interleaved

Code 128

EAN 128

Codabar

Code 93

Baudrates 150 to 115200 * = ACB readable ISBT 128

Inputs Pharmacode

External Trigger (optocoupled NPN or PNP) Headers and Up to four header and four

Voltage max. 30 Vdc Terminators terminator characters

Current Consumption 25 mA Operating Modes On-Line, Automatic,

max. Serial-On-Line, Test

Outputs)Configuration Modes Through menus using:

OUT1, OUT2 (optocoupled) WinHost utility

Host Mode (commands from

CE max. 40 Vdc one of the serial ports)

Collector Current 40 mA continuous; Code Selection Up to six different codes

max. 130 mA pulsed during one reading phase

CE Saturation 1V at 10 mA max. Decoding Safety Can enable multiple good

Power Dissipation 90 mW at 40 °C reads of the same code

max. (Ambient temp.) Special Functions ACB (Advanced Code Builder)

Motor Off

OPTICAL FEATURES Parameter Storage Non-volatile internal EEPROM

Light Source semiconductor laser diode ENVIRONMENTAL FEATURES

Wavelength In the range 630 to 680 nm Operating 0° to +40 °C (+32° to +104 °F)

Safety Class Class 2 - EN 60825-1; CDRH Temperature

Storage -20° to +70 °C (-4° to +158 °F)

USER INTERFACE Temperature

LED Indicators Laser ON, Good Read, Humidity max 90% non condensing

External Trigger, Vibration Resistance 14 mm @ 2 to 10 Hz;

Data TX / Power ON IEC 68-2-6 test FC 1.5 mm @ 13 to 55 Hz;

2 G @ 70 to 200 Hz;

PHYSICAL FEATURES 2 hours on each axis

Dimensions 68x83.6x34 mm (2.7x3.29x1.3 in) Shock Resistance 30 G;

Weight 330 g. (11.64 oz) IEC 68-2-27 test EA 11 ms; 3 shocks on each axis

Protection Class IP65

DS2400A QUICK GUIDE

Accessories:

Name Description Part Number

GFC-2100 90° Reading Device 93A201000

GFC-2000 105° Reading Device 93A201080

OM2000 Oscillating Mirror 93A251031

INT-30 (for C-Box 100) 20 mA Current Loop Interface Board 93A151022

C-BOX 100/200 Connection Box 93ACC1510, 93ACC1520

C-BOX 300/310 Connection Box Profibus 93A301000, 93A301030

C-BOX 400/410 Connection Box DeviceNet 93A301010, 93A301040

MEP-542/543 Photocell Kit NPN/PNP 93ACC1727, 93ACC1728

Electrical Connections:

DS2400A is equipped with a cable terminated by a 25-pin female D-sub connector for connection to the power

supply, communication interface and input/output signals. You can bring system cables directly to the 25-pin

connector or you can connect the scanner directly to one of the various C-Box models and bring system wiring to

it (see the relative C-Box Installation Manual).

CAUTION

Do not connect GND and SGND to different (external) ground references. GND and SGND

are internally connected through filtering circuitry which can be permanently damaged if

subjected to voltage drops over 0.8 Vdc.

The details of the connector pins are indicated in the following table:

25-pin D-sub female connector pinout

Pin Name Function

13 VS Power supply input voltage +

25 GND Power supply input voltage -

1 CHASSIS Chassis Ground

9 VS External Trigger supply voltage +

18 EXT TRIG+ External Trigger +

19 EXT TRIG- External Trigger -

8 OUT1 + Output 1 +

11 OUT2 + Output 2 +

12, 22 OUT REF Output reference

20 RXAUX Auxiliary RS232

21 TXAUX Auxiliary RS232

23 CTSAUX Auxiliary handshake RS232

24 RTSAUX Auxiliary handshake RS232

6, 10, 14,

15, 16, 17

NC Not Connected

25-pin female connector

Pin RS232 RS485

Full-Duplex

RS485

Half-Duplex

2 TX232 TX485+ RTX485+

3 RX232 RX485+

4 RTS232 TX485- RTX485-

5 CTS232 RX485-

7 SGND SGND SGND

DS2400A QUICK GUIDE

Mechanical Installation:

23.3*

0.92

0.55

3.31

0.16

10.3

0.41

1.57

0.41

10.3

1.57

14.7

0.58

M 4 n° 4

1.29

32.7

inch

2.68

1.81

DS2100A

4.2

7.8

20°

2.5

R40

4.2

90°

13.8

17.5

2.5

4.2n°2

1 x 45° n° 2

* The quote refers to the scan line

Input/Output Connections:

INPUT NPN INPUT NPN MEP-543

EXT TRIG+

+ 5V

DS2400A EXTERNAL TRIGGER

Signal

Vext 30 Vdc max.

EXT TRIG-

Input NPN command using external power

MEP-543 Connector

DS2400A

+ 5V

25 GND

EXT TRIG+

EXT TRIG-

2 1

(brown)

(white)

(blue)

Input NPN command using MEP-543 Photocell

OUTPUT

EXTERNAL TRIGGER

DS2400A

Signal

+ 5V

25 GND Ground

EXT TRIG+

EXT TRIG-

Input NPN command using DS2400A power

USER INTERFACE

8/11

12/22 OUT REF

DS2400A Vext 40 Vdc max.

Output open collector connections

INPUT PNP

+ 5V

DS2400A EXTERNAL TRIGGER

Signal

Ground

EXT TRIG+

EXT TRIG-

Vext 30 Vdc max.

Input PNP command using external power

CE max = 40 Vdc

max = 40 mA continuous

EXTERNAL TRIGGER

DS2400A

+ 5V

25 GND Ground

Signal

EXT TRIG+

EXT TRIG-

Input PNP command using DS2400A power

DS2400A

DS2400A QUICK GUIDE

Connectivity:

RS232 Main Interface Connections RS485 Main Interface Connections

RS232 Point-to-point layout RS485 Point-to-point layout

cMain Serial Interface (RS232) cMain Serial Interface (RS485 Full Duplex)

dAuxiliary Serial Interface (Local Echo) (RS232) dAuxiliary Serial Interface (Local Echo) (RS232)

eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode)

Pass-through layout Multiplexer layout

cMain Serial Interface (RS232) cMain Serial Interface (RS485 Half-Duplex)

dAuxiliary Serial Interface (RS232) dAuxiliary Serial Interface (Local Echo) (RS232)

eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode)

RS232 Master/slave layout RS485 Master/slave layout

cMain Serial Interface (Slaves RS232 only) cAuxiliary Serial Interface (RS232)

dAuxiliary Serial Interface (RS232) dMain Serial Interface (RS485 Half-Duplex)

eExternal Trigger (for On-Line Mode) eExternal Trigger

Host

MX4000

Host

DS2400

Terminal Host

DS2400

Terminal

Host

DS2400

Host

DS2400

Slave

DS2400

Slave

DS2400

Maste

Host

DS2400

Slave

DS2400

Slave

DS2400

Maste

DS2400A QUICK GUIDE

Reading Diagrams:

DS2400A-0200 (Short Reading Range)

CONDITIONS

Optic Version = Linear

Code = Interleaved 2/5 or Code 39

PCS = 0.90

Pitch angle = 0°

Skew angle = 10°

Tilt angle = 0°

* Code Resolution = High

* Code Reading Condition = Standard

* Scanning Speed = Speed_3 (800 scans/s)

* Parameters selectable in WinHost.

7,5

2,5

7,5

2,5

51015

20 25 30 35 cm

264 12

810 14 in

≥0.35 mm

(14 mils)

0.20 mm

(8 mils)

0.25 mm

(10 mils)

DS2400A-1200 (Medium Reading Range)

CONDITIONS

Optic Version = Linear

Code = Interleaved 2/5 or Code 39

PCS = 0.90

Pitch angle = 0°

Skew angle = 10°

Tilt angle = 0°

* Code Resolution:

High – for 0.25 mm (10 mils) codes

Std – for 0.35 mm (14 mils) codes and

greater

* Code Reading Condition = Standard

* Scanning Speed = Speed_3 (800 scans/s)

* Parameters selectable in WinHost.

10 20 30 40 50 cm

412816 20

≥0.50 mm

(20 mils)

0.25 mm

(10 mils)

0.35 mm

(14 mils)

DS2400A QUICK GUIDE

DS2400A-2200 (Long Reading Range)

CONDITIONS

Optic Version = Linear

Code = Interleaved 2/5 or Code 39

PCS = 0.90

Pitch angle = 0°

Skew angle = 10°

Tilt angle = 0°

* Code Resolution:

High – for 0.35 mm (14 mils) codes

Std – for 0.50 mm (20 mils) codes and

greater

* Code Reading Condition = Standard

* Scanning Speed = Speed_3 (800 scans/s)

* Parameters selectable in WinHost.

10 20 30 40 50 60 70 cm

12 16 20 24 28 in

≥ 0.50 mm

0.35 mm (20 mils)

(14 mils)

User Interface:

The following table contains the pinout for standard RS232 PC Host interface. For other user interface types

please refer to their own manual.

RS232 PC-side connections

9-pin male connector

2514

25-pin male connector

Pin Name Pin Name

2 RX 3 RX

3 TX 2 TX

5 GND 7 GND

7 RTS 4 RTS

8 CTS 5 CTS

How To Build A Simple Interface Test Cable:

The following wiring diagram shows a simple test cable including power, external (push-button) trigger and PC

RS232 COM port connections.

DS2400A

25-pin D-sub male

SGND

RXAUX

TXAUX

GND

9-pin D-sub female

GND

EXT TRIG+

Power Supply

VS (10 – 30 Vdc)

Power GND

Trigger

EXT TRIG-19

Test Cable for DS2400A

DATALOGIC S.p.A.,

Via Candini, 2

40012 - Lippo di Calderara

Bologna - Italy 05

dichiara che

declares that the

déclare que le

bescheinigt, daß das Gerät

declare que el

DS2400A-XXXX Laser Scanner e tutti i suoi modelli

and all its models

et tous ses modèles

und seine modelle

y todos sus modelos

sono conformi alle Direttive del Consiglio Europeo sottoelencate:

are in conformity with the requirements of the European Council Directives listed below:

sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:

der nachstehend angeführten Direktiven des Europäischen Rats:

cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:

89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi

and further amendments

et ses successifs amendements

und späteren Abänderungen

y succesivas enmiendas

Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti.

On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.

Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des produits.

Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit

entsprechen.

Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas

de seguridad relativas al producto.

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:

This declaration is based upon compliance of the products to the following standards:

Cette déclaration repose sur la conformité des produits aux normes suivantes:

Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:

Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:

EN 55022 (Class A ITE), August 1994:

Amendment A1 (Class A ITE), October 2000:

LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE

CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENT

EN 61000-6-2, October 2001: ELECTROMAGNETIC COMPATIBILITY (EMC)

PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL

ENVIRONMENTS

Lippo di Calderara, 08/09/2005

Ruggero Cacioppo

Quality Assurance Supervisor

821000923 (Rev. C1)

Indice

Altri manuali Datalogic Lettore di codici a barre

Datalogic

Datalogic Touch 65 pro Manuale utente

Datalogic

Datalogic PowerScan RF Istruzioni operative

Datalogic

Datalogic PowerScan BT8300 Family Manuale utente

Datalogic

Datalogic Gryphon I GBT4500 Manuale utente

Datalogic

Datalogic Formula 8500 Manuale utente

Datalogic

Datalogic DX6400 Manuale utente

Datalogic

Datalogic Magellan 800i Manuale utente

Datalogic

Datalogic Matrix 300 Manuale utente

Datalogic

Datalogic BC-80X0 Cradle Manuale utente

Datalogic

Datalogic DS8110 Manuale utente

Datalogic

Datalogic DS6300 Manuale utente

Datalogic

Datalogic TC1200 Manuale utente

Datalogic

Datalogic S5N-PH Series Manuale utente

Datalogic

Datalogic PowerScan PD8530 Manuale utente

Datalogic

Datalogic QuickScan I QM21X1 Manuale di installazione e funzionamento

Datalogic

Datalogic PowerScan D8330 Manuale utente

Datalogic

Datalogic Dragon M101 Manuale utente

Datalogic

Datalogic QuickScan I QM2131 Manuale di installazione e funzionamento

Datalogic

Datalogic Gryphon I GBT4100 Manuale utente

Datalogic

Datalogic QuickScan QS2500 Manuale di installazione e funzionamento

Datalogic

Datalogic Gryphon I GD44XX Manuale utente

Datalogic

Datalogic Gryphon GFE4400 Guida rapida alla configurazione

Datalogic

Datalogic QLM500 Manuale utente

Datalogic

Datalogic Magellan 1100i OEM Manuale per l'uso e la cura

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente

Atid

Atid AT188N Plus Manuale utente