Datexel DAT8016 Guida utente
Modbus TCP ermocouple input module DAT8016.
Set Up the DAT8016.
1. Open your web browser.
2. Type 192.168.1.100 into the address bar.
3. Click enter and the following page
should be seen.
Entering the User-name and Pass-
word.
1. e password is Fact_user.
2. e Password is Fact_pwd.
3. Click Enter, Run to run the soware.
DATEXEL LLC
www.datexel.com
Call 561 779 5660 for technical support. 1 of 4
To congure the DAT8016.
It is extremely important to use
a Cat 5 Crossover cable unless a
router is used.
1. Connect 24 Vdc to O and P.
2. Connect CAT5 crossover cable to PC and
Ethernet RJ45 Port on the DAT8016.
3. Connect a Calibrator or short the input to
1 and 2.
4. Power up the DAT8016 Modbus TCP
ermocouple Module.
Select the Language.
1. Click English.
2. Click enter.
How to read the Analog Input
Signal.
1. Click the Analog Input at the bottom of the
page.
2. Select the type of input being measured.
3. Select Tc K for K type thermocouple.
4. Click Save to save to the DAT8016.
5. Click Read to measure the Input.
6. Adjust the calibrator to check the range.
2 of 4
2
o
f
4
e device name should appear in the center
of the page. You are also able to “Logout” of the
DAT8016, go “home”, or go “back” to the page
before, by clicking the icons on the page.
e input selection can be seen below.
250mV, J type thermocouples, K type ther-
mocouples, R type thermocouples, S type
thermocouples, T type thermocouples, B type
thermocouples, E type thermocouples, N type
thermocouples.
Each input can be dierent and they are all iso-
lated from each other.
e red indication under Break means the input
is open circuit. By clicking the “Set Same Input”
button you enable all the inputs to be the same as
Analog Input 0.
3 of 4
Network Settings.
1. Modify the network settings.
2. Click Save to save the new Network settings.
System Conguration Settings.
1. To change the name from DAT8016 type the
new name and click enter.
2. To change the Modbus Address for the er-
mocouple to Modbus TCP, change it under
the ModBus Address label and click save.
3. You can enable the Watchdog timer and set a
time.
4. Set up the watchdog event and the power-up
event register.
3
o
f 4
Soware Update.
1. Obtain new soware from Datexel and save
to the local machine.
2. Enter the User_name and the password.
3. Click upgrade and follow the prompts.
4. e rmware version of the DAT8016 is dis-
played on this page.
e IP address must be unique to the network.
4 of 4
e User_name and Password
page.
1. Enter the new User_name click save.
2. Enter the new Password click save.
Indice
Altri manuali Datexel Sistema I/O
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
