DCB PAS v2 Manuale utente

PAS v2

Priority Audio Switch

User’s Guide

Version 2, Revision C

Revised Nov 25, 2019

Version 2.0c

TABLE OF CONTENTS

Certifications..............................................................2

FCC Statement...............................................................2

RoHS..............................................................................2

Chapter 1 Introduction..............................................3

Package Contents...........................................................3

P S Hardware Specifications........................................4

Chapter 2 Installation and Confi uration................5

Overview........................................................................5

Chapter 3 Connectors................................................6

Power Connector............................................................6

RJ-45 E&M Connection Pin-outs..................................7

Revision &B RJ45 Pin ssignments...........................8

Connection details..........................................................8

Chapter 4 Operation..................................................10

Common Uses................................................................10

Operation Details............................................................10

Cascaded P S................................................................11

Indicator LED's..............................................................11

Chapter 5 Troubleshootin ........................................12

Hardware Problems........................................................12

Appendix A Specifications.........................................13

P S Specification...........................................................13

Appendix B Warranty................................................14

DCB Product Two Year Limited Warranty..................14

Appendix C Schematic...............................................15

Revision C Reference Schematic...................................15

Appendix D Accessories.............................................16

Mounting Options..........................................................16

Certifications

FCC Statement

This device complies with the limits for a Class digital device, pursuant to Part 15 of the FCC rules.

This equipment has been tested and found to comply with the limits for a Class digital device pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and if not installed and used in accordance with the instruction

manual may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the

user will be required to correct the interference at the user's own expense.

ll trademarks and trade names are the properties of their respective owners.

RoHS

Some models of this product are available in RoHS versions.

Chapter 1

Introduction

This chapter provides an overview of the PAS features and capabilities.

The Priority udio Switch (P S) is designed to be installed between a transmitter site and

two control operator positions so they can share a single transmitter. The P S takes in two

4-wire audio lines each with a Push-to-Talk (PTT) lead where PTT is activated by shorting

this lead to ground. The ports are designated as Priority and Secondary. The Priority port

will seize control of the audio channel when its PTT lead is shorted to ground, otherwise the

Secondary ports audio channel and PTT state are passed through to the output port.

The P S contains two completely isolated instances of the priority switching function.

The standard P S is powered by 48VDC, which matches most telco systems. External

power supplies are available for C or other DC power operations.

Receive audio and other return leads from the transmitter are always passed back to both

controllers.

Input Ports Power and Output Ports

Package Contents

You should find the following items packaged with your P S product:

The P S unit

Optional power supply (if ordered)

If any of the above are missing, contact your dealer immediately.

PAS Hardware Speci ications

Connectors

•One 48 VDC power port

•Four RJ-45 audio input ports

•Two RJ-45 audio output ports

•Two audio input ports are paired with each audio output port

Controls

• There are no user software controls. The unit is operational upon power application.

Environmental

•Operation: -25° C to +65° C, non condensing humidity

Physical / Electrical

•5 ¼ x 5 ½ x 1 ¾ Inches

•Power requirements: 48 VDC, which may be supplied by a 120 V C power adapter

•One pound unit weight

Chapter 2

Installation and Configuration

Overview

The P S is connected between two audio sources and a single audio receiving device. There are two

instances of this operation, and they may be cascaded to allow for three inputs to a single transmitter, or

used independently with two inputs to each of two transmitters. It is usually installed at a transmitter site to

allow automatic operation by multiple control operators of the transmitter.

ll connections to the P S use RJ-45 connectors or the power connector screw terminals.

udio Source Connections:

Switched Transmit Audio Flow

Received audio from the transmitter is always passed to pins 3 & 6 of both priority and secondary devices.

Chapter 3

Connectors

Power Connector

Green screw connector (numbered right to left)

Pin 1 -48 VDC

Pin 2 Chassis ground

Pin 3 +48 VDC

RJ-45 E&M Connection Pin-outs

The following table shows the PRIMARY, SECONDARY and OUTPUT po t pin assignments. The

OUTPUT po t Audio Out signals on pins 1 and 2 a e switched between PRIMARY and

SECONDARY po t based on the PRIMARY po t PTT (E1) input on pin 4. The two ight most

columns show the OUTPUT signals when PRIMARY PTT input is OPEN and SHORTED to GND.

PRIMARY RJ45 RJ45

OUTPUT

PRI PTT (E1) Open

OUTPUT

PRI PTT (E1) GND

Audio In (R1) 1 1 Audio Out (R2) Audio Out (R1)

Audio In (T1) 2 2 Audio Out (T2) Audio Out (T1)

Audio Out (R) 3 3 Audio In (R) Audio In (R)

PTT In (E1) 4 4 PTT Out (E2) PTT Out (E1) GND

SG/EB (GND) 5 5 SG/EB (GND) SG/EB (GND)

Audio Out (T) 6 6 Audio In (T) Audio In (T)

M 7 7 M M

SB/MB 8 8 SB/MB SB/MB

SECONDARY RJ45

Audio In (R2) 1

Audio In (T2) 2

Audio Out (R) 3

PTT In (E2) 4

SG/EB (GND) 5

Audio Out (T) 6

M 7

SB/MB 8

Revision A&B RJ45 Pin Assignments

This table shows the cu ent RJ45 pin numbe s in the left hand column and the olde Rev B pin

numbe s in the fa ight column. The signal di ections a e noted in the PRI/SEC and OUTPUT

columns. This table is included only or re erence with products produced prior to

Revision C. Do not use this table unless you are replacing a previous version and

connecting the older PAS cables to a Revision C unit.

Rev C

RJ45 Signal PRI/SEC OUTPUT

Rev B

RJ45

1 Audio In (R1) IN OUT 6

2 Audio In (T1) IN OUT 3

3 Audio Out (R) OUT IN 5

4 PTT (E) IN OUT 7

5 SG/EB (GND) GND GND 8

6 Audio Out (T) OUT IN 4

7 M OUT IN 2

8 SB/MB OUT IN 1

Connection details

The P S was originally designed to be placed in between a Loop channel bank and a transmitter connected

to it via an E&M Card.

Loop Telecom channel banks (V4200, AM3440, O9500, O9550, IP6704A) with 8EM, 8EMA or

QEMA cards

To connect a Loop channel bank E&M card (LEM) to the priority and/or secondary ports of the P S,

configure the LEM to operate in B-Side mode and connect with the proper RJ45 cable.

To connect to a LEM on the output side port of the P S, configure the LEM card to operate in -Side

mode and connect with the proper RJ45 cable.

Since the P S always uses the “E lead” for PTT indicator and E-Lead PTT is always done via connection

to ground, all E&M types are supported in LEM and will pass through the P S when the LEM cards are

properly configured for -side and B-side.

Charles Industries channel banks with 3652-80 and 3652-81 E&M Cards

To connect to a Charles channel Bank E&M card (CIEM), build an RJ45 cable that connects to the specific

pins on the 50 pin Telco connector (or connectors for 3252-80) for the channels that you wish to use.

To connect a CIEM to the priority and secondary ports of the P S connect the following pins to the pins in

a straight-through fashion. That is M to M, R to R, etc. The pattern is:

Pin 8 to MB, Pin 7 to M, Pin 2 to T1, Pin 6 to T, Pin 3 to R, Pin 1 to R1, Pin 4 to E and Pin 5 to EB

If you are connecting a CIEM to the output side ports of the P S, then you must cross over the signals and

you can only use E&M Types 4 & 5. This is because CIEM can only accept PTT input on the M-Lead, the

P S only can only signal PTT by closure to ground, and E&M types 4 & 5 are the only E&M types where

PTT is signaled by closure to ground on the M lead. The pattern is:

Pin 8 to EB, Pin 7 to E, Pin 2 to T, Pin 6 to T1, Pin 3 to R1, Pin 1 to R, Pin 4 to M and Pin 5 to MB

Other channel banks

Connections to other channel banks and E&M devices can be made by following the directions of the

signals in the chart above to connect to your device. Remember that the P S input ports can only use

closure to ground to detect PTT and the unit passes the PTT state out only via closure to ground. This

required that choose an appropriate E&M type that signals PTT or accepts PTT based on closure to ground.

Groundin

Remember that grounding is critical with E&M signaling, so you must either connect the P S using the

center pin of the power supply terminal to the same ground plane as your other equipment (when using

E&M type 1 or E&M type 5) or you must connect pin 5 of the RJ45 (SG or EB lead) to the ground plane of

your equipment (When using E&M type 2-4).

Indice

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente